NAVY MIL-DTL-17060 G-2009 MOTORS ALTERNATING CURRENT INTEGRAL-HORSEPOWER SHIPBOARD USE《船用整数马力交流电动机》.pdf

1、Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05M2, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. Since contact

2、 information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 6105 INCH-POUND MIL-DTL-17060G(SH) 8 January 2009 SUPERSEDING MIL-M-17060F(SH) 25 May 1995 DETAIL SPECIFICATION MOTORS, ALTERNATING CUR

3、RENT, INTEGRAL-HORSEPOWER, SHIPBOARD USE This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for three-ph

4、ase, alternating current (AC) motors for shipboard use in frame sizes not less than 182. 1.2 Classification. Motors furnished in accordance with this specification have the following services as specified (see 6.2): a. Service A - Heavy-duty, high impact, shock-resistant motors for driven auxiliarie

5、s including propulsion which are essential to the military effectiveness of a ship. b. Service C - Commercial marine motors for driven auxiliaries which are not essential to the military effectiveness of a ship. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified

6、in sections 3, 4, and 5 of this specification. This section does not include documents cited in other section of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that th

7、ey must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to th

8、e extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATIONS QQ-B-654 - Brazing Alloys, Silver FEDERAL STANDARDS FED-STD-H28 - Screw-Thread Standards for Federal Services Provided by IHSNot for ResaleNo r

9、eproduction or networking permitted without license from IHS-,-,-MIL-DTL-17060G(SH) 2 COMMERCIAL ITEM DESCRIPTIONS A-A-59581 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Bore Diameters under 10 mm A-A-59582 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension

10、Series 19 A-A-59583 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 10 A-A-59584 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 02 A-A-59585 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 03 A-A-5958

11、6 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Dimension Series 04 A-A-59587 - Bearing, Ball, Annular, Single Row, Radial, Filling Slot, Dimension Series 02 A-A-59589 - Bearing, Ball, Annular, Single Row, Radial, Filling Slot, Dimension Series 03 A-A-59595 - Bearing, Ball, Annular

12、, Single Row, Radial, Non-Filling Slot, Cartridge Type Without Grease Plug, Dimension Series 32 A-A-59596 - Bearing, Ball, Annular, Single Row, Radial, Non-Filling Slot, Cartridge Type Without Grease Plug, Dimension Series 33 A-A-59597 - Bearing, Ball, Annular, Double Row, Radial, Internal Self-Alig

13、ning, Dimension Series 02 A-A-59598 - Bearing, Ball, Annular, Double Row, Radial, Internal Self-Aligning, Dimension Series 03 A-A-59599 - Bearing, Ball, Annular, Double Row, Radial, Internal Self-Aligning, Dimension Series 22 A-A-59600 - Bearing, Ball, Annular, Double Row, Radial, Internal Self-Alig

14、ning, Dimension Series 23 A-A-59623 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 through 22, Dimension Series 19 A-A-59624 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 through 22, Dimension Series 10 A-A-59625 - Bearing, Ball, Annular, Single Row

15、, Angular Contact, Contact Angle 11 through 22, Dimension Series 02 A-A-59626 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 through 22, Dimension Series 03 A-A-59627 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 11 through 22, Dimension Series 04 A-A-

16、59628 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 through 32, Dimension Series 10 A-A-59629 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 through 32, Dimension Series 02 Provided by IHSNot for ResaleNo reproduction or networking permitted without

17、 license from IHS-,-,-MIL-DTL-17060G(SH) 3 A-A-59630 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 through 32, Dimension Series 03 A-A-59631 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 23 through 32, Dimension Series 04 A-A-59632 - Bearing, Ball, An

18、nular, Single Row, Angular Contact, Contact Angle 33 through 45, Dimension Series 10 A-A-59633 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 through 45, Dimension Series 02 A-A-59634 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 through 45, Dimensi

19、on Series 03 A-A-59635 - Bearing, Ball, Annular, Single Row, Angular Contact, Contact Angle 33 through 45, Dimension Series 04 A-A-59636 - Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Contact, Vertex of Contact Angles Outside Bearing Dimension Series 32 A-A-59637 - Bearing, Ball,

20、 Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 33 A-A-59638 - Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Inside Bearing, Dimension Series 32 A-A-59639 - Bearing, Ball, Annular, D

21、ouble Row, Angular Contact, Filling slot, Vertex of Contact Angles Inside Bearing, Dimension Series 33 A-A-59640 - Bearing, Ball, Annular, Double Row, Angular Contact, Filing Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 32 A-A-59641 - Bearings, Ball, Annular, Double Row, Angular

22、Contact, Filling Slot, Vertex of Contact Angles Outside Bearing, Dimension Series 33 A-A-59685 - Grease, Sealed Ball and Roller Bearing A-A-59720 - Sealing and Locking Compounds, Single-Component DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-S-901 - Shock Tests, H.I. (High-Impact) Shipboard Machinery, Eq

23、uipment, and Systems, Requirements for MIL-E-917 - Electric Power Equipment, Basic Requirements (Naval Shipboard Use) MIL-DTL-1222 - Studs, Bolts, Screws, and Nuts for Applications Where a High Degree of Reliability is Required; General Specification for MIL-E-2036 - Enclosures for Electric and Elec

24、tronic Equipment, Naval Shipboard MIL-DTL-15024 - Plates, Tags, and Bands for Identification of Equipment, General Specification for MIL-P-15024/5 - Plate, Identification MIL-E-16298 - Electric Machines Having Rotating Parts, Accessories and Associated Support Items: Packaging of MIL-T-16366 - Termi

25、nals, Electric Lug and Conductor Splices, Crimp-Style Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17060G(SH) 4 MIL-PRF-17331 - Lubricating Oil, Steam Turbine and Gear, Moderate Service MIL-B-17931 - Bearings, Ball, Annular, for Quiet Oper

26、ation MIL-DTL-18240 - Fastener Element, Self-Locking, Threaded Fastener, 250 F Maximum MIL-L-19140 - Lumber and Plywood, Fire-Retardant Treated MIL-R-21248 - Rings, Retaining (Tapered and Reduced Section Type) MIL-I-24092 - Insulating Varnishes and Solventless Resins for Application by the Dip Proce

27、ss MIL-I-24178 - Insulation Tape, Electrical, Semi-Cured Thermosetting Resin Treated Glass, Armature Banding, Naval Shipboard DOD-G-24508 - Grease, High Performance, Multi-Purpose (Metric) MIL-C-24707 - Castings, Ferrous, General Specification for MIL-C-24707/l - Castings, Ferrous, for Machinery and

28、 Structural Applications MIL-C-24707/5 - Castings, Ductile Iron and Austenitic Ductile Iron MIL-M-24738 - Monitors, High Temperature Motor Protection DEPARTMENT OF DEFENSE STANDARDS MIL-STD-108 - Definitions of and Basic Requirements for Enclosures for Electric and Electronic Equipment MIL-STD-461 -

29、 Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment MIL-STD-740-1 - Airborne Sound Measurements and Acceptance Criteria of Shipboard Equipment MIL-STD-740-2 - Structureborne Vibratory Acceleration Measurements and Acceptance Criteria of Shipboard

30、 Equipment MIL-STD-2037 - Procedure to Obtain Certification for Electric Motor Sealed Insulation Systems (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-

31、5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract. AMERICAN BEARING MANUFACTURERS ASSOCIATION (ABMA) ABMA 9 - Load Rating

32、s and Fatigue Life for Ball Bearings ABMA 20 - Radial Bearings of Ball, Cylindrical Roller and Spherical Roller Types, Metric Design (Copies of these documents are available from the American Bearing Manufacturers Association, 2025 M. Street, NW, Suite 800, Washington DC 20036 or online at www.abma-

33、dc.org.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17060G(SH) 5 AMERICAN WELDING SOCIETY (AWS) AWS A5.8 - Specification for Filler Metals for Brazing and Braze Welding (DoD adopted) (Copies of this document are available from the Americ

34、an Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126 or online at www.aws.org.) ASTM INTERNATIONAL ASTM A47/A47M - Standard Specification for Ferritic Malleable Iron Castings (DoD adopted) ASTM A153/A153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware (DoD adopt

35、ed) ASTM A216/A216M - Steel, Castings, Carbon, Suitable for Fusion Welding, for High Temperature Service (DoD adopted) ASTM A29/A29M - Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for ASTM A489 - Standard Specification for Carbon Steel Lifting Eyes (DoD

36、adopted) ASTM A677 - Standard Specification for Nonoriented Electrical Steel, Fully Processed Types ASTM A683 - Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types ASTM A757/A757M - Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing

37、and Other Applications, for Low-Temperature Service ASTM B21/B21M - Standard Specification for Naval Brass Rod, Bar, and Shapes (DoD adopted) ASTM B23 - Standard Specification for White Metal Bearing Alloys (Known Commercially as Babbitt Metal) ASTM B26/B26M - Standard Specification for Aluminum-All

38、oy Sand Castings (DoD adopted) ASTM B30 - Standard Specification for Copper-Base Alloys in Ingot Form ASTM B505/B505M - Standard Specification for Copper-Base Alloy Continuous Castings ASTM B633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel (DoD adopted) ASTM D4727

39、/D4727M - Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes ASTM D5948 - Standard Specification for Molding Compounds, Thermosetting (Copies of these documents are available from ASTM International, 100 Barr Harbor Dr., P.O. Box C700, West Consho

40、hocken, PA 19428-2959 or online at www.astm.org.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17060G(SH) 6 INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC) IEC 60034-18-41 - Qualification and Type Tests for Type 1 Electrical Insulation Sys

41、tems Used in Rotating Electrical Machines Fed From Voltage Converters IEC 61934 - Electrical Measurements of Partial Discharge (PD) During Short Rise Time and Repetitive Voltage Impulses (Copies of these documents are available from the IEC, 3 rue de Varemb, P.O. Box 131, CH-1211 Geneva 20, Switzerl

42、and or online at www.iec.ch.) NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) NEMA MW1000 - Magnet Wire (Copies of this document are available from the National Electrical Manufacturers Association, 1300 North 17thStreet, Suite 1847, Rosslyn, VA 22209 or online at www.nema.org.) SAE INTERNATION

43、AL SAE AMS2469 - Hard Anodic Coating on Aluminum and Aluminum Alloys SAE AMS7259 - Packing, Preformed - O-Ring Seal SAE AMS7276 - Packing, Preformed - O-Ring Seal (Copies of these documents are available from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or online at www.

44、sae.org.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations

45、 unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.4) in accordance with 4.2. 3.2 Reliability. Bearings shall be selected to provide a calculated B-10 life of not less than 10,000

46、 hours. Bearing life shall be calculated in accordance with ABMA 9 for single bearings and, unless otherwise specified (see 6.2), in accordance with MIL-B-17931 for duplex bearings. Bearing life extension factors, identified in ABMA 9, shall not be used in bearing life calculations. 3.3 Materials, p

47、arts, and processes. Unless otherwise specified herein, materials, parts, and processes shall be in accordance with MIL-E-917. 3.3.1 Hazardous material. Materials and parts containing asbestos, cadmium, lithium, mercury, radioactive materials, or materials giving off toxic fumes under operation shal

48、l not be used. 3.3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes econom

49、ically advantageous life cycle costs. 3.3.3 Material compatibility. Materials which (through outgassing or other physical phenomena) cause deterioration of other materials or degradation of equipment performance shall not be used. 3.4 Safety. Unless otherwise specified herein, safety shall be in accordance with MIL-E-917. The equipment shall provide protection for personnel against accidental contact with moving parts and volta