NAVY MIL-DTL-20271 E-1997 LACE GOLD - ORNAMENTAL《装饰带》.pdf

1、- MIL-DTL-2027LE 9999906 2051557 117 I INCH-POUND I MIL-DTL-20271E (MC) 28 July 1997 SUPERSEDING MIL-L-20271D (MC) 28 March 1994 DETAIL SPECIFICATION LACE, GOLD - ORNAMENTAL This specification is approved for use by U.S. Marine Corps, Department of the Navy, and is available for use by all Departmen

2、ts and Agencies of the Department of Defense. 1. SCOPE 1.1. Scope. This specification covers requirements for synthetic, tarnish-resistant gold lace with an interwoven scarlet center stripe. 1.2. Classification. following classes, as specified (see 6.2). The lace will be of one type in the Class 1 -

3、 3/8 inch wide Class 2 - 5/8 inch wide Class 3 - 1-1/4 inch wide Class 4 - 1-1/2 inch wide Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commander (PSE-D), Marine Corps Systems Command, Qua

4、ntico, VA 22134-5010 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I FSC 8315 AMSC N/A DISTRIBUTION STATEMENT A. distribution is unlimited. Approved for public release; Provided by IHSNot for ResaleNo reproduction or net

5、working permitted without license from IHS-,-,- WIL-DTL-20271E m 9999906 2051558 053 m 2. APPLICABLE DOCUMENTS 2.1. General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specifica

6、tion or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are list

7、ed. 2.2. Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department

8、 of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2) . SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-E-17568 - Embroidery Materials, Metallic and Synthetic Met al 1 ic STAN DARDS FE DERAL FED-STD-191 - Textile Test Methods (Unless otherwis

9、e indicated, copies of the above specifications, standards, handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3. Non-Government publications. The following document(s) form a part of this document to the extent spec

10、ified herein. otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2)

11、. Unless 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- KIL-DTL-20273E = 99999Ob 2053559 TT ANSI/ASQC 21.4- Sampling Procedures and Tables for Inspection by Attributes (Application for copies should be addressed to The American National Standards

12、 Institute, 11 West 42nd Street, New York, NY 10036) Department of Defense (DoD) Standard Shades for Heraldic Yarns 1993 (Application for copies should be addressed to The Color Association of the United States, Inc., 409 W. 44 Street, New York, New York 10016-0927.) 2.4. Order of precedence. In the

13、 event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1. Standard sample. Stand

14、ard samples are furnished solely for guidance and information to the contractor (see 6.2). Variation from this specification may appear in the sample, in which case the specification shall govern. 3.2. First article. When specified (see 6.2), a sample shall be subjected to first article inspection i

15、n accordance with 4.3. 3.3. Materials. 3.3.1 Gold svnthetic metallic yarn. The gold synthetic metallic embroidery material shall conform to type III, class 8 or class 11 of MIL-E-17568. The core yarn may be silk, nylon, or mercerized cotton and shall be gold shade, cable No. 67104 (see DoD Standard

16、Shades for Heraldic Yarns 1993). 3.3.2 Center stripe. interwoven (warpwise direction) with silk thread. The color of thread shall match scarlet, shade W, cable No. 67111 (see DoD Standard Shades for Heraldic Yarns 1993). The scarlet center stripe of lace shall be 3.3.3 Colorfastness. The combined co

17、re yarn and synthetic metallic ribbon shall show good colorfastness to dry cleaning, 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20273E m 0b 2053560 703 m Fancy weave, pattern, 5 MIL-DTL-20271E (MC) Picks Ribs Pattern width (inch) per i

18、nch per inch Gold Center Gold dry and wet heat, cracking, perspiration, bleaching, light and weathering. per inch 5 5 5 5 3.3.4 Labile sulfur content. The use of dyes and compounds containing elementary sulfur capable of oxidation to sulfuric acid is prohibited. that the dyed and finished thread sha

19、ll contain no more labile sulfur than shown by the standard sample. When a standard sample is not available, the dyed and finished thread shall show no more than a slight trace of labile sulfur. The dyestuff shall be chosen and applied so (min) (min) stripe 260 35 11/64 1/32 11/64 260 35 9/32 1/16 9

20、/32 260 21 16/32 1/4 16/32 260 21 21/32 3/16 21/32 3.4. Desiqn and construction. The lace shall be designed and constructed so as to conform to the physical requirements listed in Table I. inches I 1 I 3/8 I 4 I1-1/2 3.5. Lenath of rolls. Unless otherwise specified (see 6.2), the lace shall be put o

21、n rolls of not less than 25 continuous yards nor more than 35 yards total. allowed, but no spliced piece shall be less than five yards in length. The lace shall be wound on suitable cores of the same width as the lace. fastened with gummed tape to prevent slippage and unrolling of the roll. One spli

22、ce per roll shall be The ends of the rolls shall be securely 3.6. Identification. Each roll shall have an identification ticket attached. easy reading of printed, stamped or typed markings. handwritten entries is prohibited. shall be legibly printed on the ticket with water insoluble ink: The ticket

23、 shall be light in color to permit The use of The following information Nomenclature: Specification number: Yardage : 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-2027 1E (MC) I Contract number and date: Suppliers name: Name of contracti

24、ng agency: 3.7. Workmanship. The finished lace shall conform to the quality of product established by this specification. 3.8. Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible prov

25、ided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 4. VERIFICATION 4.1. Classification of inspection. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4

26、.3). b. Conformance inspection (see 4.4). 4.2. Inspection conditions. Unless otherwise specified, all inspections shall be performed in accordance with the provisions set forth in ANSI/ASQC 21.4 4.3. First article inspection. When first article is required, inspection shall be made of completely fab

27、ricated lace for all provisions of this specification. 4.4. Conformance inspection. 4.4.1 Component and material testinq. Testing of components shall be in accordance with the applicable subsidiary specifications and standards to the extent applicable, except that this specification shall govern in

28、the event of conflict. The method of testing listed in Table II shall be as specified in FED-STD-191, wherever applicable. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20271E m 9%9990b 20515b2 584 D 1 No. det. I Results Components 1 per

29、S/unit I reported as I Threads : (1 yard) 1 1 1 TABLE Excellent, good, fair, or poor Excellent , good, fair, or poor Pass or fail Characteristics Material ident if ica t ion MIL-DTL-2 02 7 1E (MC ) Ply color Colorfastness: - light Wet (dry) cleaning Libile sulfur 3.3.2 3.3.1 3.3.2 3.3.2.1 3.3.2.1 3.

30、3.2.2 st meth Test method 1110, 1200 or 1530 Visual 5560 - 2/ 5622 2020 - l/Cone or spool or sufficient number of bobbins to total a minimum of 360 yards of each thread used (in which form purchased). - 2/The test specimens shall be exposed for a minimum of 40 standard facing hours except no appreci

31、able change in color shall be evident before the first 20 hours. After the first 20 hours, an appreciable change in shade only shall be permitted. 4.4.2 Examination of the end item. The end item shall be examined for defects listed in 4.4.2.1. The defects listed shall be counted regardless of their

32、proximity to one another, except where two or more defects represent a single local condition of the lace, in which case only the more serious defects shall be counted as one defect for each warpwise yard or fraction thereof in which it occurs. shall be one yard of each class. The number of rolls to

33、 be examined shall be selected as follows: The unit of product for this examination Lot in size in yards Sample size in rolls Up to 3,200 3,201 to 10,000 10,001 to 35,000 35,001 and over 10 15 25 35 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-J

34、 MIL-DTL-2027LE . 0b 205L5b3 La10 MIL-DTL-20271E (MC) 4.4.2.1. General defects. General defects shall be as follows: Examine General (when applicable) Cleanness Color Design Constructior Defects a. Abrasion mark. b. Any cut, hole, or tear. c. Any delamination or separation of film. d. Broken or miss

35、ing yarn. e. Uneven tension, resulting in thick and thin places. f. Tight or loose yarn, causing distortion or loopiness. g. Broken or missing end or pick. h. Tight picks. i. Course or heavy picks. j . Fine or light picks. k. Knots, slubs. a. Any spot or stain. b. Not as specified. c. Variation of s

36、hade in same roll. a. Not as specified. b. Width less than specified, including color pattern stripes. a. Selvages curled, folded or rolled. b. More than one splice. 4.4.2.2. Examination for lenqth. Xassification Major 101 102 103 104 105 106 107 108 109 110 111 Minor 201 202 203 204 205 206 207 4.4

37、.2.2.1 Individual pieces. The pieces shall be examined for gross length. Any gross length found to be less than the specified minimum length or any gross length found to be more than one yard below the gross length marked on the piece ticket or any spliced piece less than five yards long shall be co

38、nsidered a defect with respect to length. The unit of product 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-20271E D 99%99Ob 20535b4 357 D Reqmt . Test Determinations Characteristic para. method per sample unit pattern Fancy weave Table I

39、 Visual 1 Picks per inch Table I Visual 5 Ribs per inch Table I Visual 1 Width or Table I Std (For each stripe) pat tern com 1 c c for this examination shall be one roll. The sample size shall be expressed in units of one roll. The inspection level shall be as noted in the contract or purchase order

40、. 4.4.2.2.2 Total yardaqe in sample. The lot sample shall be unacceptable if the total of the actual gross length of pieces in the sample is less than the total of the gross length marked on the piece tickets. 4.4.3 Testinq of the end item. Testing of the completely fabricated lace shall be performe

41、d in accordance with Table III for the characteristics shown herein. The sample unit shall be three continuous yards. The lot size shall be expressed in units of one yard. The inspection level shall be as noted in the contract or purchase order. The requirements are applicable to the individual unit

42、. Table III. End item testinq. Results reported as: Pass or fail Average to nearest No. 1/64 inch 5. PACKAGING 5.1. Packaqinq. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by Depart

43、ment of Defense (DoD) personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department of Defense Agency, or within the

44、Military Departments Systems Command. Packaging data retrieval is available from the managing Military Departments or Defense 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-DTL-2027LE 9997706 2053565 293 MIL-DTL-2027 1E (MC) Agencys automated

45、 packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1. Intended use. The gold lace covered by this specification is intended to be used on

46、clothing and accessory items as follows: Class 1 - Chin strap for Women Marine dress caps. Class 2 - Chin strap for Male Marine dress caps. Class 3 - Evening dress trousers. Class 4 - Full dress belt for Director and Assistant Director, U.S. Marine Corps Band. 6.2. Acquisition requirements. Acquisit

47、ion documents must specify the following: a. Title, number, and date of the specification. b. Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.2). c. Packaging requirements (see 5.1) . d. Class required (1.2). e. Whether f

48、irst article is required (3.2). f. Length required (3.5). 6.3. Standard sample. For information regarding the availability of standard samples of the lace, address inquiry to procuring activity issuing the invitation for bids. 6.4. Subject term (keyword) listinq. Center stripe Chin straps Trousers 9

49、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- BIk-DTb-2023LE R 0b 205L5bb L2T R MIL- DTL-2 O 2 7 1 E ( MC ) 6.5. Chanqes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing Activity: Navy - MC Project No.