NAVY MIL-DTL-24231 10 E-2013 CONNECTORS SINGLE CABLE TYPE III 14- 24- 30- OR 40-CONDUCTOR.pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/10E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/10D(SH) w/AMENDMENT 1 2 March 1992 MIL-C-24231/10D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTORS, SINGLE CABLE, TYPE III, 14-, 24-, 30-, OR 40-CONDUCTOR This specification is approved for use by the Nava

2、l Sea Systems Command and is available for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 2

3、5. 2. The gland nut shall be tightened until the packing tightens against the wires and cables. This can be determined by moving the wires or cables gently back and forth until the wire or cable is seized by the packing. The gland nut shall be turned approximately one-fourth of a turn more to hold t

4、he wires and cables in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as this can damage the wires and cables. 3. Full or partial threads shall not extend more than 0.083 inch beyond the -inch thread length. 4. Refer to MIL-DTL-24231/5 for alternate method of manu

5、facturing connector body and installing guide pin M24231/5-071. 5. The retainer plates and the retainer plate assemblies shall be manufactured from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281, with a minimum yield strength of 40,000 lbf/in2 at 0.2 perce

6、nt offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of QQ-N-281 with a minimum yield strength of 50,000 lbf/in2 at 0.2 percent offset. 6. For welding the pin, item 35, see MIL-DTL-24231/5. 7. Unless more stringent requirements are specified, retainer plate, pac

7、king and retainer plate assembly for other special conductor arrangements (for example, LS2SWU-1 and B-16 wire combinations) shall meet the following minimum requirements: a. Positional tolerancing for all holes shall be . b. Holes shall not be located closer than 0.010 from the minimum gland nut in

8、side diameter of part number M24231/10-044 and the retainer plate position pin holes of part number M24231/10-080. c. Minimum material between holes shall be 0.031. d. Protective sleeving shall be sized to suit the number of cables required where use of the specified sleeving, item 12 or 13, is inad

9、equate. FIGURE 3. Plug sleeve - M24231/3-010.5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/10E(SH) 2 8. All dimensions are in inches. 9. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c.

10、Angular dimensions degree. d. Tolerances for rubber packing should follow the guidance provided in table XLI (RMA Drawing Designation A2 Precision) of MIL-HDBK-149. 10. The flange outside diameter is intended to coincide with commonly available 3-inch bar stock. The dimension may vary after machine

11、clean-up. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/10E(SH) 3 FIGURE 1. Connector, single cable, 14-, 24-, 30-, or 40-conductor. HARDNE SS REA DING TO BE TAKEN A T THESE P OI NT S.HARDNE SS REA DING TO BE TAKEN A T THIS F AC E AT1

12、 20-DE GREE INTERV AL S.1212 13GASK ET, O- RING,SAE- AS287 75 - 33 417PIN,M2423 1/5- 07 1SEE RE QT. 4 see figure 1. 15 Gasket, O-ring 1 1 1 1 1 SAE-AS28775-329 4/ See item 14. 16 Gasket, O-ring 1 1 1 1 1 SAE-AS28775-332 4/ See item 14. 17 Gasket, O-ring 1 1 1 1 1 SAE-AS28775-334 4/ See item 14. 18 P

13、late identification 1 1 1 1 1 CRES or Al, MIL-DTL-15024 See figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/10E(SH)27 TABLE I. Parts list Continued. Item no. 1/ Description 2/ Quantity for M24231/10- 3/ Material/specification

14、Remarks 001 002 003 004 005 19 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 13 and requirement 5. 20 Plate, retainer 1 See item 19. See figure 16 and requirement 5. 21 Plate, retainer 1 See item 19. See figure 11 and requirement 5. 22 Plate, retainer 1 See item 19. See figure 20 and require

15、ment 5. 23 Plate, retainer 1 See item 19. See figure 23 and requirement 5. 24 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 14. 25 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 17. 26 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 12. 27 Packing, Class

16、A, durometer 555 1 Rubber, ZZ-R-768 See figure 21. 28 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 24. 29 Ring, retaining 1 1 1 1 1 SPIROLOX RR-165-S, or equal See figure 1. 30 Ring, retaining 1 1 1 1 1 TRUARC 5100-225-W, or equal See figure 1. 31 Nut 1 1 1 1 1 Ni-Cu-Al, QQ-N-286 Se

17、e figure 9. 32 Nut, gland 1 1 1 1 1 Ni-Al-BRZ, ASTM B150/B150M See figure 4 and requirement 2. 33 Washer, 438 od by 2.385 id by 0.162 thick 1 1 1 1 1 Ni-Cu-Al, QQ-N-286 See figure 1; finish shall be 63 microinches. 34 Pin, positioning 2 2 2 2 2 M24231/5-054 See figure 10, figure 15, figure 18, figur

18、e 19, and figure 22. 35 Pin, guide 1 1 1 1 1 M24231/5-071 See requirements 4 and 6. 36 Insert 1 1 1 1 1 M24231/5-077 See figure 1. 37 Screw 1 1 1 1 1 M24231/5-083 See figure 1. 38 Cap, pressure-proof 1 1 1 1 1 M24231/14-011 See figure 1. 39 Wire, 15 feet As required MIL-DTL-16878/36 BJE0 See figure

19、1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/10E(SH)28 TABLE I. Parts list Continued. Item no. 1/ Description 2/ Quantity for M24231/10- 3/ Material/specification Remarks 001 002 003 004 005 40 Pin, contact 14 24 30 40 40 MIL-DTL-

20、24231 See figure 3. 50 Cable, Type LS2SWU-1, 15 ft MIL-DTL-24643/33 See figure 25. 51 Assembly, retainer plate 1 Ni-Cu, Class A, QQ-N-281 See figure 15 and requirement 5. 52 Assembly, retainer plate 1 Ni-Cu, Class A, QQ-N-281 See figure 18 and requirement 5. 53 Assembly, retainer plate 1 Ni-Cu, Clas

21、s A, QQ-N-281 See figure 10 and requirement 5. 54 Assembly, retainer plate 1 Ni-Cu, Class A, QQ-N-281 See figure 19 and requirement 5. 55 Assembly, retainer plate 1 Ni-Cu, Class A, QQ-N-281 See figure 22 and requirement 5. 56 Epoxy, resin, molded As required Cast epoxy resin, compound 5/ See figure

22、3. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-

23、ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. 5/ Arco Set 200, M.M. Reif and Co., Ivyland, PA PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

24、se from IHS-,-,-MIL-DTL-24231/10E(SH) 29 CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-059) NOTE: The activities listed above were i

25、nterested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-