NAVY MIL-DTL-24231 24 E-2013 CONNECTOR SINGLE CABLE TYPE III THREE-CONDUCTOR FOR LSTHOF-9 CABLE.pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/24E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/24D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, SINGLE CABLE, TYPE III, THREE-CONDUCTOR, FOR LSTHOF-9 CABLE This specification is approved for use by the Naval Sea Systems Command and is available for

2、use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 3. 2. Pin contact shall be Amphenol Corporat

3、ion, Size 12, solder type, part number 10-33646, with silver plate followed by gold plate not less than 0.0001 thick; or equal. Any other pin contact submitted as equal shall be subject to review by NAVSEA. 3. All dimensions are in inches. 4. Tolerances shall be as follows, or as stated: a. Decimals

4、 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. 5. The gland nut shall be tightened until the packing tightens against the wires and cables. This can be determined by moving the wires and cables gently back and forth until the wire and cable is seized by the packing. The gland nut

5、shall be turned approximately one-fourth of a turn more to hold wires and cables in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as this can damage the wires and cables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

6、S-,-,-MIL-DTL-24231/24E(SH) 2 FIGURE 1. Connector, single cable. TIG HTE N DO WNM ETAL TO MET ALASSEM BL Y, INSE RT,M OLD ED M 2 4231/24-010325F IG URE 1. Co nn ec to r, s in gle cable .PL ATE ,IDENTIFICA T I ONM 24231/24- 020ASSEM BL Y, SIN G L E C AB LE CO NN ECT OR3 PIN, F O R THOF-9 CABLEM 24231

7、/24 -001 SY M . NO . 517.13RECEPT ACL E A SSEMBLY M 2423 1/24 -001 IS S IM ILAR TO RECE PTACL E A SSEMBLY M 24231/9-0 01,EXCEPT INSERT ASSEMBL Y M2 4231 /9-0 10 IS R EPLACED BY INSERT ASSEMBL Y M2 4231 /24-010.SINGL E CABLE CO NN ECT O R ASS EM BLY SAM E A S M 2423 1/9-001EXCEPT AS SHOWNCABLE, THOF-

8、911 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/24E(SH) 3 FIGURE 2. Assembly, insert, molded 3-pin M24231/24-010. FIGURE 2. Assembly, insert, m olded 3-pin - M242 31/24-010.2CONT ACT , P INM24 23 1/ 24 -0 113 REQD (S O F TSO LDE R T

9、 OCO ND UC TO RS )1. 17 315160.233CL0.1350.270CL140.053316141.500GR OO VE , 0. 05 5RCA BL ELENGTH A S R E Q DEPO XY RE S IN ,MO LDE D9161732132R140.9670.9631324652 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/24E(SH) 4 FIGURE 3. Plat

10、e, identification M24231/24-020. 0.1 5 62 HO LE S51658CURR EN T RE V. L ET TE R A TTI ME O F MA NUFA CT UR E .18H IG H LT RS (MI N)3163MA NUF A CTU RE RSID EN TI FI CA TI O NHULL HOLE NO .REVM242 31/2 4-00 1138R116FIG URE 3. Plate, identification - M2 42 31 /2 4- 02 0 . 33 Provided by IHSNot for Res

11、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/24E(SH) 5 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/24- 3/ Material/specification Remarks 001 1 Connector, single cable, symbol no. 517.13 1 Same as M24231/9-001; except as shown. See figu

12、re 1. 2 Insert, assembly, molded 1 See items 04, 05, and 06. See figure 2. 3 Plate, identification 1 CRES or Al, MIL-DTL-15024 See figure 3. 4 Pin, contact 3 MIL-DTL-24231 See figure 2 and requirement 2. 5 Cable, LSTHOF-9 As required MIL-DTL-24643/3 See figure 1 and figure 2. 6 Epoxy resin, molded A

13、s required Cast epoxy resin compound 4/ See figure 3. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Arco Set 200, M.M. Re

14、if and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing act

15、ivity: Navy SH (Project 5935-2011-073) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-