NAVY MIL-DTL-24231 27 F-2013 CONNECTOR RECEPTACLE MULTI-PIN TYPE V FOR TYPE LS2SWU-1 CABLE.pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/27F(SH) 26 April 2013 SUPERSEDING MIL-C-24231/27E(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, MULTI-PIN, TYPE V, FOR TYPE LS2SWU-1 CABLE This specification is approved for use by the Naval Sea Systems Command and is available for use b

2、y all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figure 1. 2. All dimensions are in inches. 3. Tolerances shall be a

3、s follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/27F(SH) 2 FIGURE 1. Connector, multi-pin receptacle. 13257613810912411ASSEMB L YRECEPT

4、AC L EM24231/27- 001 FOR 2SWF- 3 CAB L E S Y M. NO . 1 2 7 1M24231/27- 002 FOR 2SWF- 4 CABL E S Y M. NO . 1 2 7 1 .1M24231/27- 003 FOR 2SWF- 7 CABL E S Y M. NO . 1 2 7 1 .2RI NG, RET A IN IN GM24231/10- 0 4 1GASKET, O -R IN GSAE-AS28775 -3 2 9GASKET, O -R IN GSAE-AS28775 -2 2 0NYLON I NS E RTM24231/

5、5- 0 7 7ASSEMBLY, I NSERT, MOLDED M2 4 2 3 1 /2 6 -0 2 0ASSEMBLY, I NSERT, MOLDED M2 4 2 3 1 /2 6 -0 3 0ASSEMBLY, I NSERT, MOLDED M2 4 2 3 1 /2 6 -0 4 0PIN,M24231/12- 0 1 2ASSEMBL Y ,RECEPTAC L EBODY ,M24231/14- 0 1 0CAP ,M24231/14- 0 1 1FIGURE 1 . Conn ector, multi -pin re ce p t a cle .Provided by

6、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/27F(SH) 3 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/27- 3/ Material/specification Remarks 001 002 003 1 Connector, receptacle, symbol no. 1271 1 - See figure 1. 2 Connector,

7、 receptacle, symbol no. 1271.1 1 - See figure 1. 3 Connector, receptacle, symbol no. 1271.2 1 - See figure 1. 4 Body, receptacle 1 1 1 M24231/14-010 See figure 1. 5 Insert, molded 1 M24231/26-020 See figure 1. 6 Insert, molded 1 M24231/26-030 See figure 1. 7 Insert, molded 1 M24231/26-040 See figure

8、 1. 8 Gasket, O-ring 1 1 1 SAE-AS28775-329 4/ Lubricate with silicone compound, SAE-AS8660; see figure 1. 9 Gasket, O-ring 1 1 1 SAE-AS28775-220 4/ See item 8. 10 Insert 1 1 1 M24231/5-077 See figure 1. 11 Pin, guide 1 1 1 M24231/12-012 See figure 1. 12 Cap, pressure-proof 1 1 1 M24231/14-011 See fi

9、gure 1. 13 Ring, retaining 1 1 1 M24231/10-041 See figure 1. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensions. 3/ Quantity is for one complete assembly of each size. 4/ Nitrile (Buna

10、N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the change

11、s. Preparing activity: Navy SH (Project 5935-2011-076) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-