NAVY MIL-DTL-24231 7 F-2013 CONNECTOR SINGLE CABLE TYPE III SEVEN-CONDUCTOR.pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/7F(SH) 26 April 2013 SUPERSEDING MIL-C-24231/7E(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, SINGLE CABLE, TYPE III, SEVEN-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use by all Departments

2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 7. 2. Full or partial threads shall not extend more than 0.083 inc

3、h beyond the -inch thread length. 3. The gland nut shall be tightened until the packing tightens against the wires. This can be determined by moving the wires gently back and forth until the wire is seized by the packing. The gland nut shall then be turned approximately one-fourth of a turn more to

4、hold the wires in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as this can damage the wires. 4. Refer to MIL-DTL-24231/5 for alternate method of manufacturing connector body and installing guide pin M24231/5-071. 5. The retainer plates and the retainer plate ass

5、emblies shall be manufactured from nickel-copper alloy in accordance with Class A, Form 1, hot-finished condition of QQ-N-281 with a minimum yield strength of 40,000 lbf/in2 at 0.2 percent offset, or nickel-copper alloy in accordance with Class A, Form 1, cold-drawn condition of QQ-N-281 with a mini

6、mum yield strength of 50,000 lbf/in2 at 0.2 percent offset. 6. For welding of the pin, see MIL-DTL-24231/5. 7. Retainer plate, packing, and retainer plate assembly for other special conductor arrangements (for example, LS2SWU-1 and B-16 wire combinations) shall meet the following requirements: a. Wh

7、ere LS2SWU-1 cable is required, the hole size shall be 1764 diameter. b. Positional tolerancing for all holes shall be . c. Holes shall not be located closer than 0.010 from the minimum gland nut inside diameter of part number M24231/5-072 and the retainer plate position pin holes of part number M24

8、231/7-030. d. Minimum material between holes shall be 0.031. e. Protective sleeving shall be sized to suit the number of cables required where use of the specified sleeving, item 18, is inadequate. 8. All dimensions are in inches. FIGURE 3. Plug sleeve - M24231/3-010.5Provided by IHSNot for ResaleNo

9、 reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 2 9. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. d. Tolerances for rubber packing should follow the guidance provided in table XLI (R

10、MA Drawing Designation A2 Precision) of MIL-HDBK-149. 10. The flange outside diameter is intended to coincide with commonly available 2-inch bar stock. The dimension may vary after machine clean-up. FIGURE 1. Connector, seven-conductor M24231/7-001, symbol no. 517.1. 18221411 24202211110284637919122

11、11523513161HARD NESS READING T O B E TAKEN AT T H ESE POIN T S.HARD NESS READING T O B E TAKEN AT T H IS F AC E AT120- DEGR EE INT ER VAL S.12NUT, GLA N DM24 231/5- 07 2SEE R EQT 3.WASH ER,M24 231/5- 07 5GASKET , O-R IN G,SAE- AS28 775- 32 7WIREPLATE, ID EN TM24 231/7- 05 1PIN, M 24 231/5- 07 1SEE R

12、EQ T 4 AN D 6.SCREW ,M24 231/5- 08 3RING, RETAININ GM24 231/7- 04 1I N SERT , NYL ONRING, RETAININ GM24 231/5- 07 6SLEEVIN G - 1 4 FT . LG0.430 I.D. X 0.030 T H K.NU T, M 24231/5- 07 4ASSY, RE TAIN ER PLAT E,M24 231/7- 03 0PAC KING, M2 4231 /7-0 32PLATE , R ETA INER , M24 231/7 - 03 1ASSY, S IN GLE

13、CABLE C ONN ECT ORBODY , M242 31/7- 04 0ASSY, I N SER T , MOLD ED ,M24 231/7- 01 0CAP , M 24 231/13- 01 1GASKET , O-R IN G,SAE- AS28 775- 32 9GASKET , O-R IN G,SAE- AS28 775- 21 3GASKET , O-R IN G,SAE- AS28 775- 22 0FIGUR E 1 . C onne ctor , sev en- co nduc tor - M2 4231 /7-00 1, sy mbo l n o . 5 1

14、7 . 1 .1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 3 0.0 590.0 49R18UN DE RCUT .0.8 900.8 6018*32*0.0 510.0 4163116R300.0 670.0 570.0 270.0 23301.1 891.1 851.3 021.2 92180.0 660.0 620.7 860.7 7629322.2 242.2 14323162-1 2U N

15、-2 A1.2 091.1 991.4 051.4 01321.6 171.6 13234SEE NOTE 3.* PI N, WELD.* 0.0 510.0 41R30132R32732125ALL OVER E XCE PTAS SHOWN .6311161. 250 -12UNF- 2BSEE REQT. 2.0.0 720.0 680.1 900.1 801. 750 -12UN-2 A1.1 301.1 201.5 551.5 451.6 301.6 201.7 501.7 452.0 051.9 9563FIGU R E 2. As se mbl y, s i ngl e ca

16、bl e co nduc tor bo dy - M2 42 31 /7- 04 0 . 20.5 050.4 950.4 420.4 3213323415161.7 551.7 452.2 242.2 145.8 805.8 7072332630.120 HOL E,0.1 87 DEEP, D O NOTPENETRATE .+0. 00 0-0. 00 5FIGURE 2. Assembly, single cable connector body M24231/7-040. 2 Provided by IHSNot for ResaleNo reproduction or networ

17、king permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 4 FIGURE 2. Assembly, si ngle cable connector body - M 24231/7- 040 - C ontinued .20.0520.050R964R1.38-32N C-2B, (2) HO LES, 316D EEP.(LO CATE TO SUIT IDE N T IF IC AT IO N P LA T E. )0.0720.068R, 2 GRO OVES 1116 LG.FIGURE 2. Assembly,

18、 single cable connector body M24231/7-040 Continued. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 5 12345670.233 (T YP)0.135 (T YP)CL0.270 (T YP)FIGU RE 3. Assembly, insert, m olded - M24231/7-010 .8171 .17 31516PIN, CONTACT

19、 , (7 R EQD )0.05338141332+132-1323161.50015 FEE T0.9670.963MOLD ED EPOXY R ESIN1414132R116WIRE , SOLD ERTO PIN C ONTA CT .0.0 55 R2325FIGURE 3. Assembly, insert, molded - M24231/7-010. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/

20、7F(SH) 6 FIG U R E 4. P lat e, ret aine r - M242 31 /7- 03 1 . 103161 .10 90.1 35 (TYP)63764, 7 HOLES132X 45 BEVELBOTH SIDE S.0.2 33 (TYP)0.2 70 (TYP)FIGURE 4. Plate, retainer - M24231/7-031. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL

21、-24231/7F(SH) 7 FIG U R E 5. P ac ki ng - M 2423 1/7 -03 2 . 20341 .10 97 H OLES, SIZE A NDLOCAT ION SA ME ASRET AINER PLATE.BEVELS NOT RE QD.FIGURE 5. Packing - M24231/7-032. 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 8

22、FIGURE 6 . Pla te, identific ation - M 24 23 1/7 -05 1 . 210.156, 2 HOLES .51658CURRENT REV. LE T T ER A TTIME O F MANU F AC T U R E.18H IGH LTRS (MI N) .3163MANUFACTUR ER SIDENTIFIC AT IO NHULL H OLE NO.REVM24 231/7-00 1138R116FIGURE 6. Plate, identification M24231/7-051. 21 Provided by IHSNot for

23、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 9 FIGURE 7. Assembly, retainer plate M24231/7-030. 1.2551.245332316PIN, POSIT IONI NG, M24231 /5-054 ( FORC E FI T )0.0670.057RSAME AS R ETA IN ER PLAT EEXCEPT AS SH OWN .24FIGURE 7 . As se mbly, re taine

24、r plate - M24 23 1/7 -03 0 . 1111 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 10 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/7- 3/ Material/specification Remarks 001 1 Connector assembly, single cable,

25、 symbol no. 517.1 1 - See figure 1. 2 Connector, body assembly, single cable 1 Ni-Cu-Al, QQ-N-286 See figure 2 and continuation of figure 2. 3 Gasket, O-ring 1 SAE-AS28775-220 4/ Lubricate with silicone compound, SAE-AS8660. 4 Gasket, O-ring 1 SAE-AS28775-329 4/ See item 3. 5 Gasket, O-ring 1 SAE-AS

26、28775-327 4/ See item 3. 6 Gasket, O-ring 1 SAE-AS28775-213 4/ See item 3. 7 Cap, pressure-proof 1 M24231/13-011 See figure 1. 8 Insert, assembly, molded 1 See items 17, 23, and 25 See figure 3. 9 Insert 1 M24231/5-077 See figure 1. 10 Plate, retainer 1 Ni-Cu, Class A, QQ-N-281 See figure 4 and requ

27、irement 5. 11 Assembly, retainer plate 1 Ni-Cu, Class A, QQ-N-281 See figure 7 and requirement 5. 12 Screw 2 M24231/5-083 See figure 1. 13 Washer 1 M24231/5-075 See figure 1. 14 Nut 1 M24231/5-074 See figure 1. 15 Pin, guide 1 M24231/5-071 See figure 1. 16 Nut, gland 1 M24231/5-072 See figure 1. 17

28、Pin, contact 7 MIL-DTL-24231 See figure 3. 18 Sleeving, 0.430 id, 0.030 thick 14 Type F, Form U, Category 1, color clear, MIL-I-631 See figure 1. 19 Ring, retaining 1 SPIROLOX PRB-131-M, or equal See figure 1. 20 Packing, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 5. 21 Plate, identificati

29、on 1 CRES or Al, Type I, MIL-DTL-15024 See figure 6. 22 Ring, retaining 1 M24231/5-076 See figure 1. 23 Wire, 15 7 MIL-DTL-16878/36 BJE0 See figure 1 and figure 3. 24 Pin, positioning 1 M24231/5-054 See figure 7. 25 Epoxy resin, molded As required Cast epoxy resin compound 5/ See figure 3. Provided

30、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/7F(SH) 11 TABLE I. Parts list Continued. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and d

31、imensions. 3/ Quantity is for one complete assembly of each size. 4/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. 5/ Arco Set 200, M.M. Reif and Co., Ivyland, PA, or PR610-TCF (Chockfast Orange),

32、 ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Navy SH (Project 5935-2011-056) NOTE: The activiti

33、es listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-