NAVY MIL-DTL-24231 9 E-2013 CONNECTOR SINGLE CABLE TYPE III SEVEN- AND NINE-CONDUCTOR.pdf

1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-24231/9E(SH) 26 April 2013 SUPERSEDING MIL-C-24231/9D(SH) 15 May 1987 DETAIL SPECIFICATION SHEET CONNECTOR, SINGLE CABLE, TYPE III, SEVEN- AND NINE-CONDUCTOR This specification is approved for use by the Naval Sea Systems Command and is available for use by all D

2、epartments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24231. REQUIREMENTS: 1. Dimensions and configuration: see figures 1 through 8. 2. The spring lockwasher, part number M24231/9-023, s

3、hall be in accordance with NASM35338-126 except that the inside diameter (id) shall be 0.796. 3. Refer to MIL-DTL-24231/5 for alternate method of manufacturing connector body and installing guide pin M24231/5-071. 4. For welding of the pin, item 23, see MIL-DTL-24231/5. 5. Unless otherwise specified

4、 (see figure 8), all dimensions are in inches. 6. Tolerances shall be as follows, or as stated: a. Decimals 0.005 inch. b. Fractions 164 inch. c. Angular dimensions degree. d. Tolerances for rubber packing should follow the guidance provided in table XLI (RMA Drawing Designation A2 Precision) of MIL

5、-HDBK-149. 7. The flange outside diameter is intended to coincide with commonly available 2 inch bar stock. The dimension may vary after machine clean-up. 8. The gland nut shall be tightened until the packing tightens against the wires and cables. This can be determined by moving the wires and cable

6、s gently back and forth until the wire and cable is seized by the packing. The gland nut shall be turned approximately one-fourth of a turn more to hold wires and cables in place. Do not overtighten the gland nut or attempt to tighten down metal to metal, as this can damage the wires and cables. Pro

7、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 2 FIGURE 1. Connector, single cable, seven- and nine-conductor. FIGURE 1. Con nec tor, singl e cable, seven- and nine- condu ctor.262887 PIN FOR MS S- 6 CABL E, 7SS-2, M24231 /9 - 00 1

8、SYM NO . 5 17 .59 PIN FOR RG -26 4A/U CA BLE, M242 31 /9 - 00 2SYM NO . 5 17.129 PIN FOR RG -26 4C/U CA BLE, M242 31 /9 - 00 312HARDNE SS REA DING TO BE TAKEN A T THESE P OI NT S.HARDNE SS REA DING TO BE TAKEN A T THIS F AC E AT1 20-DE GREE INTERV AL S.12CABLE, M2 4231 /9-0 15 , O RM2423 1/9-025, O

9、RM2423 1/9- 02 6NUT, GLAND ,M2423 1/9-01 4 ORM2423 1/9- 02 4WASH ER, SPRING L OCK ,M2423 1/9-01 3 ORM2423 1/9- 02 3SEE RE QUIREM ENT 2 .GASK ET, O- RING,SAE- AS287 75 - 32 7RING, GLAN D,M2423 1/9- 01 2OR M242 31/9- 02 2ASSY , SINGL E CAB L E CON NEC TO RBODY , M2 4231 /9-0 30 OR M242 31 /9 - 04 0ASS

10、Y , INSERT, MOLDED ,M2423 1/9-01 0 ORM2423 1/9- 02 0GASK ET, O- RING,SAE- AS287 75 - 21 3RING, RETA ININGM2423 1/7- 04 1GASK ET, O- RING,SAE- AS287 75 - 22 0CAP, M242 31/13 - 01 1 2722NUT,M2423 1/5- 07 4RING, RETA ININGM2423 1/5- 07 6WASH ER,M2423 1/5- 07 5PACK ING,M2423 1/9- 01 1OR M242 31/9- 02 1P

11、IN,M2423 1/5- 07 1SEE RE QT 3 AN D 4GASK ET, O- RING,SAE- AS287 75 - 32 9SCREW,M2423 1/5- 08 3PLATE, IDE NT ,M2423 1/9-05 1 ORM2423 1/9-05 2 ORM2423 1/9- 05 3INSERT, NYLON ,M2423 1/5- 07 731111722186 74 510 142011 1512 1630 31 322125249132319Provided by IHSNot for ResaleNo reproduction or networking

12、 permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 3 FIGURE 2. Assembly, single cable connector body M24231/9-030, M24231/9-040. FIGU RE 2. Ass embly, s ingle c able conduct or body - M24231/9-030,M24231/9-040 .+0.000-0.00572332630.120 HOLE ,0.187 DEEP, DO N O TPENET RAT E.*630.0970.087LG.

13、 TO SUIT M24231/5-0 71*PIN , 4 51.1990.0670.0571.4051.4011.6171.6130.0270.0230.0660.0622.2242.214+0.015-0.0150.7860.7760.0590.0490.0720.0680.1900.1802.0051.9955.8805.8702.0051.9951.7501.7451.6301.6201.5551.5451.1141.1041.1891.1851.3021.2920.5050.4952.2242.2140.0510.0410.4420.4320.79518*32*116R303018

14、2932323162-1 2UN-2A1.20932234SEE NOT E 3* WEL D.*0.0510.041R30132R3273213321516125ALL OV ER EXCE PTAS S HOWN.6313161.250-1 2UNF- 2B1.750-1 2UN-2A63R18UNDERCUT.4 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 4 FIGURE 2. Assemb

15、ly, single cable connector body M24231/9-030, M24231/9-040 Continued. R964R0.138-3 2NC-2B, 316DEEP, 2 HOLE S(LOCATE TO SUIT IDENTIFI CA TI O NPLATE .)4 50.0520.050FIGU RE 3. Ass embly, s ingle c able connect or body - M24231/9-030,M2423 1/9-040 - Con tin ued .4 5 Provided by IHSNot for ResaleNo repr

16、oduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 5 FIGURE 3. Assembly, insert, molded M24231/9-020. 0.0580.048FIGURE 4 . Assemb ly, inse rt, molde d - M2 4 2 3 1 / 9 -0 2 0 .714132RCABL E, M 242 31 /9 - 02 5 O RM 242 31/ 9- 02 6CL6589412311612GR OO VE R33CL1.1781.16

17、8291.5051.4950.9670.9630.0600.05031 3270.2500.2501516PIN, C ON TAC T141332+132-132316M O LDED EPO XY R ESI N7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 6 FIGURE 4. Packing M24231/9-011 (A=0.600), M24231/9-021 (A=0.782). FIG

18、URE 5. Plate, identification - M24231/9-051 (for M24231/9-001), M24231/9-052 (for M24231/9-002), M24231/9-053 (for M24231/9-003). 0.156 , 2 H O LE S51658CU RR ENT REV. LE T T E R A TTIME OF MANUF A C T U R E .18H IGH LT RS (M IN ).3163MANU FAC TUR E R SIDENT IFIC A T IO NHULL HOLE NO.REVM24231/9-001

19、, OR 9-002, O R 9 -0 03138R116FIG U RE 6. Plate, identifi cation - M24231/9-051 (for M24231/9-001), M24 231/9-052 (fo rM24231/9-002), M24 231/9-053 (for M24231/9-003 ) .28FIG URE 5. Pac king - M2 4231 / 9-0 11 (A= 0.60 0)- M2 4231 / 9-0 21 (A= 0.78 2)913MOL D OR MAR K WITH INDELIBLE I NKTHE PAR T NO

20、 . ON THIS S URFACE.DIA“A “ DIA1.2551.2451.0981.0889 13 28 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 7 FIGURE 6. Ring, gland M24231/9-012 (C=0.671), M24231/9-022 (C=0.796). FIG URE 7. Rin g, gl an d - M2 4231 / 9-0 12 (C=0.

21、6 71 )- M2 4231 / 9-0 22 (C=0.7 96 )1014 “C “63ALL OVE R164X 45 CHAMF ER, B OT H SID ES.1.0981.0880.1610.15110 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 8 FIGURE 7. Nut, gland M24231/9-014 (B=0.671), M24231/9-024 (B=0.79

22、6). F IG UR E 8. N ut , gland - M 24 23 1/ 9- 01 4 (B=0.671)- M 24 23 1/ 9- 02 4 (B=0.796)121663ALL O VER18R138316316781. 25 0- 12U NF -2A “B“12 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 9 FIGURE 8. Assembly, insert, mol

23、ded (7-conductor) M24231/9-010. FIGURE 9. Assembly , i nsert, molded (7-conduct er) - M 24231/9-010 .612345670.2330.135CL0.2701516PIN, C ON TAC T0.0580.0481.5051.49538141332+132-13231615 F EETMO LDED EPO XY R ESI N1414132R116CABLE ,M242 31/ 9- 01 5GR OO VECL12RSOLD ER1.1781.168290.0600.0500.9670.963

24、30336 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 10 TABLE I. Parts list. Item no. 1/ Description 2/ Quantity for M24231/9- 3/ Material/specification Remarks 001 002 003 1 Connector assembly, single cable, symbol no. 517.5 1

25、- 7-pin for cable MSS-6 or 7SS-2, see figure 1. 2 Connector assembly, single cable, symbol no. 517.12 1 - 9-pin for cable RG-264 A/U, see figure 1. 3 Connector assembly, single cable 1 - 9-pin for cable RG-264 C/U, see figure 1. 4 Connector body, single cable 1 Ni-Cu-Al, QQ-N-286 See figure 2 and co

26、ntinuation of figure 2 and requirement 3. 5 Connector body, single cable 1 1 Ni-Cu-Al, QQ-N-286 See figure 2 and continuation of figure 2 and requirement 3. 6 Insert assembly, molded 7-conductor 1 See items 29, 30, and 33. See figure 8. 7 Insert assembly, molded 9-conductor 1 1 See items 29, 31 or 3

27、2, and 33. See figure 3. 8 Insert 1 1 1 M24231/5-077 See figure 1. 9 Packing, M24231/9-011, Class A, durometer 555 1 Rubber, ZZ-R-768 See figure 4. 10 Ring, gland, M24231/9-012 1 Ni-Al-BRZ, ASTM B150/B150M See figure 6. 11 Washer, lock, M24231/9-013 1 MS35338-126 See figure 1. 12 Nut, gland M24231/9

28、-014 1 Ni-Al-BRZ, ASTM B150/B150M See figure 7. 13 Packing, Class A, durometer 555, M24231/9-021 1 1 Rubber, ZZ-R-768 See figure 4. 14 Ring, gland, M24231/9-022 1 1 Ni-Al-BRZ, ASTM B150/B150M See figure 6. 15 Washer, spring-lock, M24231/9-023 1 1 MS35338-126 See figure 1 and requirement 2. 16 Nut, g

29、land, M24231/9-024 1 1 Ni-Al-BRZ, ASTM B150/B150M See figure 7. 17 Gasket, O-ring 1 1 1 SAE-AS28775-220 4/ Lubricate with silicone compound, SAE-AS8660, see figure 1. 18 Gasket, O-ring 1 1 1 SAE-AS28775-213 4/ See item 17. 19 Gasket, O-ring 1 1 1 SAE-AS28775-329 4/ See item 17. 20 Gasket, O-ring 1 1

30、 1 SAE-AS28775-327 4/ See item 17. 21 Ring, retaining 1 1 1 M24231/5-076 See figure 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24231/9E(SH) 11 TABLE I. Parts list Continued. Item no. 1/ Description 2/ Quantity for M24231/9- 3/ Materia

31、l/Specification Remarks 001 002 003 22 Ring, retaining 1 1 1 M24231/7-041 See figure 1. 23 Pin, guide 1 1 1 M24231/5-071 See requirement 3. 24 Washer 1 1 1 M24231/5-075 See figure 1. 25 Nut 1 1 1 M24231/5-074 See figure 1. 26 Screw 1 1 1 M24231/5-083 See figure 1. 27 Cap, pressure-proof 1 1 1 M24231

32、/13-011 See figure 1. 28 Plate, identification 1 1 1 Corrosion-resistant steel or aluminum, MIL-DTL-15024 See figure 5. 29 Pin, contact 7 9 9 MIL-DTL-24231 See figure 8. 30 Cable, 7SS-2 15 ft MIL-DTL-915/8 See figure 1. 31 Cable, RG-264 A/U As required 5/ See figure 1 and figure 3. 32 Cable, RG-264

33、C/U As required 5/ See figure 1 and figure 3. 33 Epoxy resin, molded As required Cast epoxy resin compound 6/ See figure 3 and figure 8. NOTES: 1/ Item numbers are the same as encircled numbers shown on figures. 2/ See applicable figure or table listed in remarks column for part numbers and dimensio

34、ns. 3/ Quantity is for one complete assembly of each size. 4/ Nitrile (Buna N); Parker Hannifin Corporation (part number N0756-75), O-ring Division, 2360 Palumbo Drive, Lexington, KY 40509, CAGE 02697, or equal. 5/ Formerly shown in MIL-DTL-23020 and MIL-C-23020/4. 6/ Arco Set 200, M.M. Reif and Co.

35、, Ivyland, PA, or PR610-TCF (Chockfast Orange), ITW Philadelphia Resins Corp., Montgomeryville, PA, or equal. CHANGES FROM PREVIOUS ISSUE. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing activity: Nav

36、y SH (Project 5935-2011-058) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-