NAVY MIL-DTL-29469 A-1998 CHAPLAIN-S KIT - COMBAT《战斗牧师用具》.pdf

1、- MIL-DTL-29469A = 9999706 2064686 579 INCH-POUND MIL-DTL-29469A(MC) 2 April 1998 SUPERSEDING MIL-C-29469 (MC) 20 July 1994 DETAIL SPECIFICATION CHAPLAINS KIT - COMBAT This specification is approved for use by U.S. Marine Corps, Department of the Navy, and is available for use by all Departments and

2、 Agencies of the Department of Defense. 1. SCOPE 1.1. Scope. This document establishes the requirements for a Chaplains Combat Kit with carrying case. 2. APPLICABLE DOCUMENTS 2.1. General. in sections 3 and 4 of this specification. include documents cited in other sections of this specification or r

3、ecommended for additional information or as examples. every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. The documen

4、ts listed in this section are specified This section does not While Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commander (PSE-D), Marine Corps Systems Command, Quantico, VA 22134-5010 by

5、 using the Standardization Document Improvement Proposal Form 1426) appearing at the end of this document or by letter. (DD FSC 9925 AMSC N/A DISTRIBUTJON STATEMENT A. distribution is unlimited. Approved for public release; Licensed by Information Handling ServicesMIL-DTL-294bqA 999990b 20b4b87 405

6、2.2. Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of

7、Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPEC1 FICAT I ONS FEDERAL A-A-50199 - Thread, Polyester Core, Cotton or Polyester A-A-50356 - Handkerchief, Mens or Womens A-A-52106 - Cloth, Twill or Plain Weave, Polyester and Polyes

8、ter Blend V-T-285 - Thread, Polyester L-P-390 Covered - Plastic Molding and Extrusion Material, Polyethylene and Copolymers (Low, Medium, and High Density) DEPARTMENT OF DEFENSE MIL-C-508 - Cloth, Oxford, Nylon, 3 Ounce MIL-W-4088 - Webbing, Textile, Woven Nylon MIL-T-5038 - Tape, Textile and Webbin

9、g, Textile, Reinforcing, Nylon MIL-H-9890 - Hardware, Individual Load Carrying Equipment: and Hardware, Miscellaneous MIL-W-17337 - Webbing, Textile, Woven Nylon MIL-R-20092 - Rubber or Plastic Sheets and Assembled and Molded Shapes, Synthetic, Foam or Sponge, Open Cell MIL-T-31000 - Technical Data

10、Packages, General Specification for MIL-F-21840 - Fastener Tapes, Hook and Loop, Synthetic MIL-C-43734 - Cloth, Duck, Textured Nylon MIL-W-43668 - Webbing, Textile, Textured or Multifilament MIL-C-44031 - Cloth, Camouflage Pattern: Woodland, Cotton Nylon and Nylon STANDARDS 2 Licensed by Information

11、 Handling ServicesMIL-DTL-29YbA m 0b 2064688 341 m MIL-DTL-29469A (MC) FEDERAL FED-STD-4 - Glossary of Fabric Imperfections FED-STD-595 - Colors Used in Government Procurement FED-STD-751 - Stitches, Seams and Stitchings DEPARTMENT OF DEFENSE MIL-STD-100 - Engineering Drawing Practices MIL-STD-973 -

12、 Configuration Management MIL-STD-2219- Fusion Welding for Aerospace Applications (Unless otherwise indicated, copies of the above specifications, standards, handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Oth

13、er Government documents and publications. The following other Government documents and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS 14-1-164 - Chaplains Kit, Combat (Assault), Illustrati

14、on 14-1-165 - Carrying Case, Sheet 1 of 2 (spec notes) 14-1-165 - Carrying Case, Sheet 2 of 2 (parts) 14-1-167 - Carrying Strap Quick Release, (male) 14-1-181 - Carrying Strap Quick Release, (female) 14-1-166 - Accessory Case 14-1-168 - Cross/Crucifix Assembly with Base 14-1-169 - Cross/Crucifix Ada

15、pter Assembly 14-1-170 - Cross/Crucifix (dimensions) 14-1-171 - Cross/Crucifix Adapter (dimensions) 14-1-178 - Cross/Crucifix, Base Assembly 14-1-179 - Cross/Crucifix, Base (dimensions) 14-1-180 - Cross/Crucifix, Bushing 14-1-172 - Chalice Assembly 14-1-173 - Chalice Adapter Assembly 14-1-174 - Chal

16、ice Cup 14-1-175 - Chalice Adapter 14-1-176 - Chalice, Intinction Cup 14-1-177 - Chalice, Paten 14-1-178 - Chalice, Base Assembly 14-1-179 - Chalice, Base (dimensions) of Components Licensed by Information Handling Services MIL-DTL-29469A 9999906 2064689 288 14-1-180 - Chalice, Bushing 14-1-182 - Py

17、x Assembly 14-1-183 - Pyx, Base 14-1-184 - Pyx, Lid 14-1-185 - Pyx, Ring 14-1-186 - Pyx, Hinge Pin 14-1-187 - Card, Prayer 14-1-188 - Card, Absolution and Anointing 14-1-189 - Protective Insert, Bottom 14-1-190 - Protective Insert, Top 14-1-191 - Cloth, Corporal 14-1-192 - Cloth, Purificator and Fin

18、ger Towel 14-1-193 - Stole (Copies of the drawings are available from the U.S. Marine Corps Systems Command, SSC, Quantico, VA 22134-5010) 2.3. Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues o

19、f the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). ANSI/ASQC 21.4 - Sampling Procedures and Tabl

20、es for Inspection by Attributes (Application for copies should be addressed to The American National Standards Institute, 11 West 42nd Street, New York, NY 10036.) ASTM A 240 - Standard Specification for Heat-Resisting Chromium and Chromium - Nickel Stainless Steel Plate, Sheet, and Strip for Pressu

21、re Vessels ASTM D 1056-91 - Type II, Class A, Grade TBD, Suffix SCE- F2-TBD * (Application for copies should be addressed to American Society for Testing and Materials, 1916 Race St., Philadelphia, PA 19103.) 4 Licensed by Information Handling Servicest MIL-DTL-29469A 9999906 2064690 TTT MIL-DTL-294

22、69A (MC) 2.4. Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Nothing in this document, 3.

23、 REQUIREMENTS 3.1. First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.3. 3.2. Materials and components. The materials and components used in the construction shall be in accordance with the drawings and parts lists indexed in Section

24、 2.2.2 and this specification. 3.2.1 Material and material colors for carrier and accessory case. Material for construction of the carrier and accessory case shall conform to class 3 of MIL-C-43734, which is 1000 - denier type 440 cordura nylon material coated with water proofing substance to create

25、 finished weight of 12 oz., but not less than 11 oz. All material colors for the carrier and accessory case shall be in accordance with FED-STD-595. Acceptable colors chips are: 34082; 34083; 34084; 34086; 34088 or 34089. 3.2.2 Metal material. All metal material shall be type 304 corrosion resistant

26、 steel. When construction is complete, the chalice cup, intinction cup, paten, cup base, cross base, pyx base and pyx lid shall measure .O40 +O -.010. The cross material shall be stainless plate, type 304, .125 thick per ASTM A 240. 3.3. Desiqn and construction. The design and construction shall be

27、in accordance with the drawings listed in Section 2.2.2 and this specification. Tolerances for overall dimensions on components shall be in accordance with the manufacturers commercial practice unless otherwise specified herein. 3.3.1 Major components list. The components of the chaplains kit are de

28、signed to fit snugly in the carrying case in the quantities indicated: 5 Licensed by Information Handling ServicesMIL-DTL-29469A W 9979906 2064693 936 W MIL-DTL-29469A(MC) Nomenclature uant i t y Reference Bottle, wide mouth, plastic (2 oz.) Bottle, wide mouth, plastic (4 oz. ) Bottle, plastic, pres

29、s lock cap Card, absolution and anointing Card, prayer Chalice (cup, base, intinction 6 paten) Cloth, corporal Cloth, purif icator Cloth, finger towel Cross and crucifix Oil stock PYX Reconciliation stole Stole Carrying case Accessory case Container, priest bread Insert, protective List, parts 1 3.3

30、.2.1 1 3.3.2.1 1 3.3.2.2 1 3.3.2.3 1 3.3.2.4 1 3.3.2:s 1 3.3.2.6 1 3.3.2.7 1 3.3.2.7 1 3.3.2.8 1 3.3.2.9 1 3.3.2.10 1 3.3.2.11 1 3.3.2.12 2 3.3.2.13 1 3.3.2.14 1 3.3.2.15 1 3.3.2.16 1 3.3.2.17 3.3.2 Description of components. 3.3.2.1, Bottle, wide mouth, plastic. The wide mouth clear plastic bottles

31、 with screw caps shall be of two or four ounce capacity: 3.3.2.2. Bottle/tube, plastic, with cap. The bottle/tube with press lock cap shall be of flexible, yet sturdy plastic and be capable of holding between 50 and 70 communion host/wafers. 3.3.2.3. Card, absolution and anointinq. The absolution an

32、d anointing card shall measure 3-3/4 by 2-3/4 inches (21/8 inch tolerance) and shall be made from 50 or 60 pound, gray color or off white color stock, using 12-pitch bold print (reduced by 30 percent), laminated on both sides with 5-mil (minimum plastic). Laminated border edges shall be at least 1/8

33、 inch. The text for each side of this card shall be as shown on Drawing 14-1-188. 3.3.2.4. Card, prayer. The prayer card shall measure 5-3/16 by 4-3/16 (5 1/8 inch tolerance), with a 1/8 inch minimum border. Corners are to be rounded, and shall be made from 50 to 60 pound, gray or off white color st

34、ock, using 12 pitch bold print, laminated on both sides, with 5-mil (minimum) plastic. Laminated 6 Licensed by Information Handling Services MIL-DTL-29469A W 9999906 2064692 872 MIL-DTL-29469A (MC) border edges shall be at least 1/8 inch. The text shall be in accordance with Drawing 14-1-187. 3.3.2.

35、5. Chalice assemblv (CUP, base, intinction cup and paten)-. The chalice assembly shall be made from corrosion resistant steel per 3.2.2 that allows for field use without requiring special protection or cleaning. It shall be constructed in accordance with the Drawings 14-1-172, 14-1-173, 14-1-174, 14

36、-1-175, 14-1-176, 14-1-177, 14-1-178, 14-1-179, 14-1-180 (see Parts List 14-1-172 and 14-1-173). The exterior of the chalice shall be mill finished in a manner to prevent reflection, and the interior of the chalice cup, intinction cup and paten will be a polished finish. chalice cup to prevent forei

37、gn matter from entering in windy conditions. The paten shall fit securely over the opening of the The chalice and the paten shall have no markings. 3.3.2.6. Cloth, corporal. The cloth shall measure 17 inches square (i 1/16 inch), have hemmed edges, color per acceptable color chips in paragraph 3.2.1

38、, and conform to cotton material of A-A-50356. The cloth shall have a small black cross (1 inch high, 1/2 inch wide 2 1/16 inch), embroidered in the horizontal center, 6-1/4 inches from the bottom edge of the cloth using embroidery thread conforming to 150/2 denier rayon, bright luster, multifilamen

39、t, black color, No. 67111 in accordance with Drawing 14-1-191. 3.3.2.7. Cloths, purificator and finqer towel. The cloths, one for the purificator and one for the finger towel, shall be made from cotton material conforming to A-A-50356, color per acceptable color chips in 3.2.1, with a small black cr

40、oss (no larger than 1 inch by 1/2 inch) embroidered in the center 5 inches from the top edge of the cloth. All edges shall be hemmed. Construction and material requirements for the cloths shall be in accordance with Drawing 14-1-192. They shall measure approximately 17 inches in length by 8-1/2 inch

41、es in width. Thread will be in accordance with 3.3.2.6 for the corporal. 3.3.2.8. Cross and crucifix. The cross and crucifix shall be made from corrosion resistant steel, in accordance with 3.2.2,. that will allow for field use without requiring special protection or cleaning. It shall be constructe

42、d in accordance with Drawings 14-1-168, 14-1-169, 14-1-170, 14-1-171 and 14-1-180. The base shall be constructed in accordance with Drawings 14-1-178, 14-1-179 and Parts List 14-1-168. The cross will accommodate both Catholic and Protestant religious usage 7 Licensed by Information Handling Services

43、 MIL-DTL-29469A m 9999906 2064693 709 m MIL-DTL-29469A (MC) e (Catholic on one side and Protestant on the other side). When assembled, the cross and crucifix will measure approximately 6-1/2 inches (2 /4 inch) in height and consist of a base that allows display in an upright manner, and allow breaki

44、ng down for storage in carrying case. The cross crucifix will have a mill finish to inhibit reflection. Etching will be in accordance with 3.5.2. Welding will be in accordance with 3.3.3. 3.3.2.9. Oil stock. The oil stock shall be made of metal as noted in 3.2.2. Dimensions shall be 1 inch in diamet

45、er, 3/4 inch in height (+ 1/16 inch), with same material screw cap which includes a cork liner inside the cap. attached by a welded clip to the bottom of the oil stock so that when the ring is closed against the oil stock the periphery of the ring does not extend more than 1/16 inch from the outer f

46、ringe edge of the oil stock. The exterior shall be of mill finish. in accordance with 3.3.3. The finger ring shall be The oil stock shall have no markings. Welding shall be 3.3.2.1O1pYX. The pyx shall be of sufficient size to held between eight to 12 hosts, and be constructed of corrosion resistant

47、steel per 3.2.2 that will allow for field use and require minimum cleaning. Exterior shall be of mill finish and the interior of polished finish. It shall be in accordance with Drawings 14-1-182, 14-1-183, 14-1-184, 14-1-185, 14-1-186 and Parts List 14-1-182. Hinge may be welded. or secured by metal

48、 fabrication. If welded on the base or cover of the pyx, it is recommended that the hinge be centered on the base to allow for welding. Welding shall be in accordance with 3.3.3. The pyx shall have no markings. 3.3.2.11.Reconciliation stole. The reconciliation stole shall be white on one side and da

49、rk purple on the other with white trim on both sides. This can be accomplished by attaching a smaller piece of purple material upon a piece of larger whiter material. Material shall be of a durable, stain resistant polyester or nylon; white material is 1-3/4 inches wide; purple material is 1-1/2 inches wide; both purple and white pieces are 48 inches long. A gold cross shall be embroidered thru to include both sides on each end of the stole. The best side shall be purple. It is 1-1/2 inches long, with a cross bar of 1 inch, placed 1/2 inch from the top of th