NAVY MIL-DTL-7793 14 A-2012 METER TIME TOTALIZING MINIATURE DIGITAL 28 VDC OR 26 VAC 50 TO 2400 Hz SQUARE.pdf

1、AMSC N/A FSC 6645 INCH-POUND MIL-DTL-7793/14A 19 October 2012 SUPERSEDING MIL-M-7793/14 15 December 1988 DETAIL SPECIFICATION SHEET METER, TIME TOTALIZING, MINIATURE, DIGITAL, 28 VDC OR 26 VAC, 50 TO 2400 Hz, SQUARE This specification is approved for use by all Departments and Agencies of the Depart

2、ment of Defense. Reactivated after 19 October 2012 and may be used for new and existing designs and acquisitions. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-7793. FIGURE 1. Meter dimensions. Provided by IHSNot for ResaleNo reprod

3、uction or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 2 REQUIREMENTS: 1. Dimensions. Dimensions are as specified in Figure 1. All dimensions are in inches. Unless otherwise specified, tolerances are 0.02 for two-place decimals and 0.015 for three-place decimals. 2. Mounting fl

4、ange. The mounting flange, threaded extension and threaded protection cap shall be constructed of aluminum alloy with an olive drab chromate coating over cadmium plating. 3. Protection cap. The protection cap shall be in accordance with MS25043-10DA per SAE-AS25043 except for the finish and means of

5、 attachment. The finish shall be in accordance with that for the mounting flange in Requirement 2 above. The metallic chain shall be replaced with a nylon lanyard. 4. Dielectric strength. The meter shall be capable of withstanding the application of 600 VRMS (room) and 350 VRMS (altitude) between th

6、e terminals and the case. 5. Life accuracy. Meter accuracy shall be 0.1 percent from -85 to 257 F (-65 to 125 C) and 10 to 34 VDC, or 20 to 30 VAC at 50 to 2400 Hz. Qualification tests shall be performed on 3 meters each, for DC and AC accuracy. 5. Power consumption. Power consumption at 28 volts VD

7、C shall not exceed 50 milliwatts and at 26 VAC, 400 Hz AC shall not exceed 25 milliwatts. 6. Ripple voltage. The meter shall continue to operate as specified in MIL-DTL-7793 when subjected to a cyclic peak of ripple voltage (see Note 3) of less than 2.0 VDC and the frequency-voltage coordinates on f

8、igure 2. 6.1 Ripple voltage measurement. The ripple voltage shall be measured with a peak reading voltmeter in series with a 4.0-microfarad capacitor. The higher of the two values measured when the voltmeter is successively connected to each of two polarities shall be considered the ripple voltage.

9、6.2 Frequency characteristics. The frequency components of the ripple voltage shall be within the limits on Figure 2 when measured as conducted interference. 7. Operating temperature range. The operating temperature range shall be from -85 to 257 F (-65 to 125 C). 8. Part Number. The part number is

10、M7793/14-1. 9. Time range. Total readout of the meters shall be 99999.99 hours. 10. Meter output. The output from the meter shall be in a serial binary coded decimal format. The output impedance shall be 100K 10%. A logical “zero” shall be between 0.0 to Provided by IHSNot for ResaleNo reproduction

11、or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 3 +0.2 volt. A logical “one” shall be between +3.3 and +6.6 volts. The output pin assignments are shown in Figure 3 and the output data format as shown on figure 4. 11. Transient protection. No temporary or permanent degradation s

12、hall be produced in the meter for the input voltage and time values shown on figure 5 and figure 6 (80V and 600V transient, respectively). 11.1 Transient voltage. Transient surge voltages shall be within the limits on figure 3 when converted to their equivalent step functions. Transient spike voltag

13、es shall be within the limits shown on figure 6. They shall be not greater than 600V nor depart from the normal wave form for more than 50 microseconds. 12. Durability of cap and threads. There shall be no mechanical or electrical degradation after 100 cycles in accordance with SAE-AS50151. 13. Volt

14、age range. The operating voltage shall be from 10 to 34 VDC or 20 to 30 VAC, 50 to 2400 Hz. 14. Durability of connectors and contacts. No mechanical or electrical degradation shall occur to connectors or contacts after 100 cycles in accordance with SAE-AS50151. Operational accuracy shall be checked

15、at the end of the test. 15. Weight. The weight shall be not greater than 1.0 ounce with the attached protection cap. 16. Tensile strength of lanyard. The lanyard shall withstand a tensile load of 25 pounds when applied to Axis “A” and Axis “B” as shown on figure 1. 17. Environmental thermal stress s

16、creening test profile. Temperature range: -65 C to +125 C Temperature rate of change: 2 C/Minute Minimum (Chamber air temperature) Temperature dwell duration: 30 minutes minimum Temperature cycles: 5 cycles minimum Power on/Equipment operating: Power at 10 VDC for DC Meter or 26 VAC/400 Hertz for AC

17、 Meter. The meter shall be turned on and off a minimum of three times at each temperature extreme (-65 C and +125 C) for each cycle. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 4 18. Qualification tests. Qualification tests shall

18、 be conducted in accordance with MIL-DTL-7793, except that the accuracy, voltage, temperature, and thermal shock or environmental stress screening shall be as specified herein. In lieu of Thermal Shock, 100% Environmental Thermal Stress Screening may be performed on 100% of meters supplied under thi

19、s specification sheet. Salt spray, moisture resistance, vibration, shock, electromagnetic compatibility and low temperature storage shall be conducted with the protective cap in place Hermetic seal test is not applicable. NOTES: 1. Elapsed time is read from the M7793/14-1 meter by mating the M7793/1

20、4-1 meters connector with the M7793/12-1 readers connector and operating the reader. 2. Digital readout and meter face plate per MIL-DTL-7793 are not applicable since the digital readout is provided by the separate M7793/12-1 reader. 3. AC operation may be from either sinusoidal or square wave sourc

21、es. 4. The meter is designed to have an electrical ground and a continuous EMI/RFI shield with the treaded protection cap in place. 5. Contacts shall meet all the requirements of silver plated solder contacts from SAE-AS50151. Provided by IHSNot for ResaleNo reproduction or networking permitted with

22、out license from IHS-,-,-MIL-DTL-7793/14A 5 FIGURE 2. Frequency characteristics of ripple in 28 VDC electric systems. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 6 FIGURE 3. Readout pin assignment. FIGURE 4. Output data format. P

23、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 7 DC Volts Time (Seconds) FIGURE 5. Transient surge step function loci limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-7

24、793/14A 8 FIGURE 6. Envelope of spike voltages for direct current equipment. 10-6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-7793/14A 9 Changes from previous issue. Marginal notations are not used in this revision to identify changes wit

25、h respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-7793, this specification sheet references SAE-AS25043 and SAE-AS50151. Custodians: Preparing activity: Army - MI Navy - AS Navy - AS (Project 6645-2012-016) Air Force - 99 Review activities

26、: Navy - OS, SH DLA - GS1 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-