NAVY MIL-E-24269 B (1)-1990 EXTINGUISHER FIRE CARBON DIOXIDE 15 POUND PORTABLE PERMANENT SHUTOFF NAVY SHIPBOARD USE《海军军舰用途15英镑便携式持久栓二氧化碳灭火器》.pdf

1、MILWARY SPECIFICATION EXTINGUISHER, FIRE, CARBON DIOXIDE, 15 POW, PORTABLE, PERMANENT SHUTOFF, NAVY SHIPBOARD USE This amendment forins a part of ML-E-24269B(SH), dated 14 June 19B, and kv approved for use by the Naval Sea Systems Command, Deparhnent of the Navy and iS available for use by all Depar

2、tments and Agencies of the Deparhnent of Defense. PAGE 1 1.2 Delete and substitute: “1.2 Classification. The fire extinguishers covered by this specification shall be of the following classes, as specEec (see 6.2.1): Class 1 - Alloy steel Class2 - Aluminum Class 3 - Stainless steel“ PAGE 4 3.1: Dele

3、te and substitute: “ 3.1 First article. When specified (see 6.21), a sample shall be subjected .o first article inspection (see 6.3) in accordance with 4.4.“ AMSC NIA. FSC 4210 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. c PAGE 1 of 4 Provided by IHSNot for Resa

4、leNo reproduction or networking permitted without license from IHS-,-,- MIL-E-242698 (1) LI2 799990b 0457533 MIL-E-24269B(SH) AMENDMENT1 3.3, Last sentence, delete and substitute: “The class 2 extinguishers shall be listed as marine type by ANSVUE, in accordance with ANSVUL 154.“ PAGE 7 3.5.3: Delet

5、e and substitute: “3.5.3 Discharge hose assemblv. The overall length of the discharge hose shall be 37 4 2 inches.“ I 3.5.3.3, Second sentence, delete and substitute: I “The discharge horn shall be fabricated of temperature, electric, and water-resistant material having 1/4-18 NPT (for classes 1 and

6、 3) interna or 1/4-18 NPT (for class 2) external thread bronze or brass connection molded or otherwise secured to the horn for attaching the handle.“ PAGE 8 3.5.5: Delete and substitute: “3.5.5 Mounting bracket. Unless otherwise specified (see 6.2.1), a mounting bracket shall be provided. The mounti

7、ng bracket shall be a heavy duty vehicle type. The bracket . . shall also be adjustable to retain cylinders at the diameter range specified in 3.5.1.“ PAGE 9 3.7.1, Add to the end of paragraph title, “(classes 1 and 3)“. PAGE 10 3.7.3: Add as new paragraph. “3.7.3 Namedate (class 2). A nameplate and

8、 other markings on class 2 extinguishers shall be provided as specified on ANSVUL 154.“ 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L 3.7.4 Add as new paragraph. “3.7.4 Weieht information. The empty weight of the extinguisher (cylinder and valv

9、e) shall be stamped on the cylinder dome i.e. curvature area. The marking shall be “W followed by the numerical weight to nearest tenth of a pound. For example, a empty extinguisher that weighs 34.5 pounds should be marked “W 34.5“. The letter size shall be 1/4 inch.“ 3.8 Delete in its entirety. 3.9

10、 Delete and substitute: “3.9 Drawines. (see 6.2.2)? 4.3: Delete in its entirety. . PAGE 11 4.4, Delete last sentence. PAGE 16 6.;Below “NOTESw, add the following “(This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.)“ PAGE 17 6.2.2: Delete

11、and substitute: “6.2.2 Consideration of data requirements. The following data requirements should be considered when this specification is applied on a contract. The applicable Data Item Descriptions (DIDS) should be reviewed in conjunction with the specific acquisition to ensure that oniy essential

12、 data are requested/provided and that the DIDS are tailored to reflect the requirements of the specific aquisition. To ensure correct contractual application of the data requirements, a Contract Data Requirements List (DD Form 1423) must be prepared to obtain the data, except where DOD FAR Supplemen

13、t 27.475-1 exempts the requirement for a DD Form 1423, L- , 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Reference ParavraDh DID Number DID Title Suevested Tailoring 3.9 DI-DRPR-81102 Developmental Design Drawings and Associated Lists - - - 4.5.

14、3 DI-T-2072 Reports, tests q-c- The above DIDs were those cleared as of the date of this specification. The current issue of DoD 5010.12-L, Acquisition Management Systems and Data Requirement Control List (AMSDL), must be researched to ensure that only current, cleared DIDs are cited on the DD Form

15、1423.“ , 6.2.2.1: Delete in its entirety- 6.2.3: Add as new paragraph “6.2.3 Technical manuals. The requirement for technical manuals should be considered when this specification is applied on a contract, If technical manuals are required, military specifications and standards that have been cleared

16、 and listed on DoD 5010.12-L, Acquisition Management Systems and Data Requirements Control List (AMSDL) must be listed on a separate Contract Data Requirements List (DD Form 14231, which is included as an exhibit to the contract. The technical manuals must be acquired under separate contract line item in the contract.“ . Preparing activity: Navy - SI3 (PrQject 421-N46 .4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-