NAVY MIL-F-17619 E-1981 FRAME SERVICE CAP (MAN-S)《男式军帽框》.pdf

1、-_ BIL-F-17bLSE 8LJ 777770b 0380633 T I f- e-23-/S - MIL-F-l7619E(NU) 28 October 1981 MIL-F-17619D (SA) . SUPERSEDING 7 January 1975. MILITARY SPEC IF ICATION FRAME, SERVICE CAP (MANS) This specification is approved for use by the Navy Clothing and Textile Research Facility, and is available for use

2、 by all Departments and Agencies of the Department of Defense. 1 . _- . .- ._ 1,- -.SCOPE. . .-. . . -_ - 1.1 Scope - This specification covers the requirements for cap frames, to. be worn by nuile personnel of the Navy and Coast Guard. *112 Classi?ication - The cap frames shall be procured in the f

3、ollowing types, classes, styles, and sizes as specified (see 6.2). Type I - Frame, with cloth top visor Class 1 - For Flag Rank Officers Class 2 - For Captains and Commanders Type II - Frame, with plastic top visor Class 1 - With 2 silver buttons (NAVY) Class 3 - With 2 gold buttons (CG) Class 4 - W

4、ith 2 gold buttons (NAVY) Style A - Front stand with removable crown support wire Style B - Front stand with non-removable crown support wire Schedule of sizes 6 112 7 114 6 518 7 318 6 314 7 112 6 718 7 518 7 7 314 7 118 7 718 8 Beneficial comments (recommendations, additions, deletions) and any pe

5、rtinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing For Clothing, Equipage, and Tentage (General Use) MILITARY MIL-B-3461 - Buttons, Insignia, Metal, Uniform and Cap MIL-S-3577 - Sweatband, Headwear, Leather MIL-C-16290 - Cloth, Melton

6、, Wool (Moth-Proofed) MIL-E-17568 - Embroidery Materials, Metallic and Synthetic Metallic MIL-L-43541 - Leather, Cattlehide, for Visors and Chinstraps MIL-T-43548 - Thread, Polyester, Cotton, Covered MIL-S-43993 - Sweatband, Headwear, Artificial Leather MIL-C-82252 - Cloth, Broadcloth, Wool, and Woo

7、l-Synthetic (Moth-Proof ed) STANDARDS FEDERAL FED-STD-151 - Metals, Test Methods FED-STD-191 - Textile Test Methods FED-STD-311 - Leather, Methods of Sampling and Testing FED-STD-595 - Colors FED-STD-751 - Stitches, Seams and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspe

8、ction MIL-STD-129 - Marking for Shipment and Storage by Attributes LAWS AND REGULATIONS U.S. POSTAL SERVICE MANAL (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, D. C. 20402.) 2 Provided by IHSNot for ResaleNo reproduction or n

9、etworking permitted without license from IHS-,-,-MIL-F-L7bLSE 8Li 7979706 0380633 3 II MIL-F-l7619E(NU) (Copies of specifications, standards, drawings, and publicatians required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as dire

10、cted by the contracting officer.) 2.2 Other publications - The following documents form a part of this specification to the extent specified herein, Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply: NATIONAL MOTOR FREIGHT T

11、RAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to American Trucking Association, Traffic Department, 1616 P Street, N.W., Washington, D. C. 20036.) Inc., ATm: UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Ap

12、plication for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606.) 3. REQUIREMENTS 3.1 Guide sample - Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). may appear in the sample,

13、 in which case this specification shall govern. Variations from this specification * 3.2 sample unit(s) for first article inspection and approval (See 4,2). First article - When specified (See 6.2), the contractor shall furnish 3.3 Materials - * 3,3.1 cap frame visor top and for covering the bottom

14、edge of the inner band on type I and II cap frames shall conform to type I, class 2 of MIL-C-16290 or type I, class III or type II, class 3 of MIL-C-82252. * 3.3.2 polyethylene plastic material, white, natural or black in color, conforming to type I, II or III, class H, grades 1 or 2 of L-P-390, exc

15、ept that the low temperature brittleness, dielectric constant, dissipation factor, and thermal stress cracking requirements shall not be applicable. molded into a shape similar to those shown in figure 3. of the plastic material shall be 0.050 inch. 4.3.1. Cloth, wool or wool/synthetic - The cloth u

16、sed for the type I Front stand - The front stand shall be made of a high density (linear) The front stand shall be The minimum thickness Testing shall be as specified in 3.3.2.1 Stiffness - The front stand material shall have a minimum stiffness scale rating of 55 when tested as specified in 4.3.1.

17、3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- - -_I_ ._ MIL-F-L76LSE 4 7777706 0380634 5 I MIL-F-176193 (NU) 3.3.2.2 Bending - The front stand material shall show no evidence of cracking when tested as specified in 4.3.1. 3.3.3 Cloth, cotton t

18、will - The cloth, unbleached, shall be suitable for laminating to the wool broadcloth or melton as specified in 3.3.1, and shall be used on the type I cloth visor top. The cloth shall have a minimum of 72 ends and 60 picks per inch, weigh 6 to 8 ounces per square yard, and shall have a maximum of 15

19、 percent starch and protein content including chloroform and water-soluble material when tested as specified in 4.3.1. * 3.3.4 Plumper paper - A suitable commercial plumper paper shall be used for laminating to the plastic sheeting in the fabrication of the type II plastic visor top. The plumper pap

20、er shall be 0.020 2 0.002 inch thick and properly treated so that it retains its original shape after being subjected to the immersion test specified in 4.3.1. 3.3.5 Plastic sheeting (non-rigid) - The plastic sheeting shall be used on the type II plastic visor top and for the visor binding on types

21、I and II cap frames in accordance with the requirements specified in 3.3.5.1 and 3.3.5.2. The plastic sheeting shall be of a non-rigid porperly plasticized polyvinyl chloride or copolymer of vinyl-chloride-acetate, pigmented black approximating shade No. 17038 of FED-STD-595, and shall show no stiff

22、ening; tackiness; cracking; or flaking when tested as specified in 4.3.1. 3.3.5.1 Visor top - The plastic sheeting shall be press-polished on one side, and shall be 0.020 (+ - 0.002) inch in thickness when tested as specified in 4.3.1. Visor binding - The binding shall be fabricated from plastic 3.3

23、.5.2 sheeting, 0.012 (+ 0.003) inch in thickness and 3/4 to 7/8 inch in width when tested as specified in 4.3.1. * 3.3.6 II cap frame visors, shall conform to type II of MIL-L-43541; 6 to 7 ounces in thickness; vegetable and chrome combination tanned; except that the finish shall be of a boxed, dice

24、d, or pin-seal pattern. As an alternate, the visor bottom may be constructed of reconstituted leather (commercially referred to as PARLON). When reconstituted leather is used, the thickness shall be 6 to 7 ounces. The color of the visor bottom may be black or Hatters green. * 3.3.7 visor shall be wa

25、ter resistant and made from either natural or synthetic rubber. Testing shall be as specified in 4.3.1. Leather - The leather used in fabricating the visor bottom of types I and Adhesive - The adhesive used for bonding the component parts of the 3.3.8 Embroidered visors (Type I frame) - When cloth t

26、op visors are to be embroidered, the embroidery materials shall conform to types I, II, or III of MIL-E-17568 (see figure 2). * 3.3.9 polyethylene in flat stock or molded form conforming to the requirements specified in 3.3.9.1 and 3.3.9.2. Inner band - The inner band shall be made from a high densi

27、ty (linear) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.9.1 Standard inner band - The high density (linear) polyethylene plastic material shall be either opaque white, natural, or black, in color conforming to types I, II, or III, class H,

28、grades 1 or 2, of L-P-390, . except that the low temperature brittleness, dielectric constant, dissipation factor, and thermal stress cracking resistance requirements shall not be applicable. been extruded, stripped, slit, or cut 2 (5 1/16) inches in width, 0.050 to 0.060 inch in thickness, and shal

29、l be perforated to match the Navys reference sample (see 6.3). edges of the band material shall be unperforated. specified in 4.3.1. The standard inner band shall be made from flat stock that has A margin of 3/8 inch at the top and bottom Testing shall be as 3.3.9.1.1 Stiffness - The standard inner

30、band material shall have a stiffness (scale reading) between 11 and 27 inclusive when tested as specified in 4.3.1. 3.3.9.1.2 Bending - The standard inner band material shall show no evidence of cracking after the bending test specified in 4.3.1. 3.3.9.2 Alternate inner band - The alternate inner ba

31、nd shall be made from the material specified in 3*3.9.1, meet the requirements of 3.3.9.1.1 and 3.3.9.1.2, and shall. be molded in a cane interlaced chair seat design on one or both sides. width and shall be 0.050 to 0.075 inch in thickness. The thickness of the material in the chair seat design are

32、a shall be approximately 0.010 inch less than that in the margins. The finished width of the inner band shall be The top and bottom margins shall finish 3/16 to 1/4 inch in 2 ( ticket no. 30/3, type IB3 (glazed) 4 ply, ticket no. 24; type IC1 (mercerized) 3 ply, ticket no. A and type IC2 (mercerized

33、) 3 ply, ticket no. A and O0 of V-T-276. The color of the thread shall be bleached white or dyed black or brown to approximately match the material to which it is sewn. The dyed thread shall show good fastness to laundering, perspiration, wet-dry cleaning, and light. Thread, cotton - The cotton thre

34、ad used for seaming and stitching Note: Cotton covered polyester threads conforming to MIL-T-43548, in equivalent sizes, niay be substituted for the cotton threads. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-L7bLSE q m 9799906 O380637 O

35、m * 3.3.16.2 sweatband assembly to the cap frame shall conform to class A, type I, II or III, size E or type IV, size C of V-T-295. or brown to approximate the shade of the sweatband and shall show good colorfastness to wet-dry cleaning and perspiration. Thread, nylon - The nylonthread for seaming a

36、nd stitching the The thread shall be dyed black 3.3.17 Labels - Each cap frame shall have a combination identification-size label, a separate size label, and an instruction label conforming to the requirements specified in 3.3.17.1, 3.3.17.2, and 3.3.17.3. * 3.3.17.1 Identification-size label - The

37、combination identification and size label shall conform to type III or IV, class 4 of DDD-L-20; except that the label shall bear the following inscription: FRAME, SERVICE CAP (MANS) CONTRACT NO. : DLA100-00-0-0000 (EXAMPLE) =- STOCK NO,: 8405-00-000-0000 (EXAMPLE) SIZE: 7 (-LE) NAME OF CONTRACTOR: T

38、he printing on the label shall show fastness to dry cleaning only. 3.3.17.2 Size label, stamped or paper - The stamped size label shall conform to type IV, class 2, of DDD-L-20; except that only the size shall be designated and shall show fastness to dry cleaning only. The paper label shall be of a

39、pressure-sensitive adhesive type, with the size number printed in black with numerals not less than 5/16 inch in height. 3.3.17.3 Special instruction label - A special instruction label shall be packaged with the cap frame as specified in 5.1.1. not less than 2 inches by 3 inches. only, in letters n

40、ot less than 3/32 inch in height. follows : The label shall measure The text shall be printed on one side Inscription shall be as SPECIAL INSTRUCTIONS IF THE CIRCUMFERENCE OF THE FRAME WIRE REQUIRES LOOSENED AND RE-SECURED TO THE PROPER SIZE. ADJWIMENT TO FIT THE CAP COVER, THE CLAMP SHALL BE * 3.4

41、Design - The cap frame shall have a circular inner band made of plastic, a molded plastic front stand and a crescent shaped visor made from combinations of wool, plastic and leather. vinyl crown protector shall be used to support the cap cover. frames shall have screw type metal button fastened to e

42、ach side of frame. cap frames are supplied without buttons. removable cap covers of corresponding sizes may fit snugly over them (see figure 1 thru 4). A circular adjustable steel wire with attached Type II cap Type I The frames shall be so constructed that 3.5 Figures - Figures 1 thru 4 are furnish

43、ed for information purposes only. When inconsistencies exist between the written specification and the figures, the written specification shall govern (see 6 4). 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ - MIL-F-L76LSE 4 M 9999906 0380b38

44、2 MIL-F-17619E (NU) 3.6 Patterns - The patterns for cutting all parts of the cap frame shall be furnished by the contractor, and shall be of the proper proportions to provide good fitting cap frames conforming to the finished dimensions in Table II. 3.7 Construction - 3.7.1 Stitches, seams and stitc

45、hing - Stitch, seam, and stitching types specified in Table I shall conform to FED-STD-751. Whenever two or more methods, seams, or stitches are given for the same operation, any one of them may be used. (underthread) shall be on the inside of the cap frame. Where stitch type 101 or 401 is used, the

46、 chain or looper 3.7.2 Stitches per inch - The minimum and maximum number of stitches per inch shall be as specified in Table I. 3.7.3 Thread breaks and ends of seams - Unless otherwise specified in Table I, ends of all seams and stitching, when not caught in other seams or stitching, shall be backt

47、acked not less than 1/4 inch. The ends of a continuous line of stitching shall be overlapped not less than 1/2 inch. types) shall be secured by starting the repair stitch not less than 1/2 inch in front of break. overlap 3/8 to 5/8 inch beyond the starting point or if necessary backstitched to preve

48、nt ravelling. shall not be used unless the ends are caught in other seams or rows of stitching. * 3.8 Manufacturing operations - The cap frames shall be manufactured in accordance with operation requirements specified in Table I. not required to follow the exact sequence of operations, provided the

49、finished cap frames are identical to those produced by following the exact sequence as shown. Thread breaks (all stitch Stitchlines used on the circular sections of the cap frame must When stitch type 101 or 401 is permitted as an option, it The contractor is . t 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I H a n “I - ri al. “ +I incorrect; illegible; of improper size, and interior) locati