NAVY MIL-F-29419-1985 FRAME SHIPPING (SIXCON)《运输结构》.pdf

1、I i MI LI TARY l MIL-F-29419 (MC) 2 May 1985 MILITARY SPECIFICATION FRAME, SHIPPING (SIXCON) This specification is approved for use by the U.S. Marine Corps, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specif

2、ication establishes the requirements for manufacture and acceptance of the SIXCON Shipping Frame. 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specification, standards and handbooks. Unless otherwise specified, the following specifications, standards, and handbooks of the issue listed in t

3、hat issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. SPECIFICATIONS MIL-P- 11 6 MIL-1-6866 MIL-1-6868 MIL-W-8611 -Preservation, Methods of -Inspection, Penetrant Method of

4、 -Inspection Process, Magnetic Particle -Welding, Metal Arc and Gas, Steels, and Corrosion and Heat Resistant Alloys, Process for MIL-T-27260 -Tiedown, Cargo, Aircraft MIL-N- 27 44 4 -Net, Cargo Tiedown, Pallet MIL-E-52798 -Enamel, Alkyd, Camouflage Beneficial comments (recommendations, additions, d

5、eletions) and any b pertinent data which may be of use in improving this document should be addressed to: Commandant of the Marine Corps, Code LMA-1, Washington, D.C. 20380, by using the self-addressed Standardization Document Improvement Proposal (DD Form 14,26) appearing at the end .of this docume

6、nt or bv letter. FSC 8145 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-29419 (MC) STANDARDS MI LI TARY MIL-STD-105 -Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 -Marking for Shipment and Storage MIL-STD-130 -Identi

7、fication Marking of U. S. Military Property MIL-STD-453 -Inspection, Radiographic MIL-STD-794 MIL-STD-810 -Parts and Equipment, Procedures for Packaging and Packing of -Environmental Test Methods and.Engineering Guidelines 2.1.2 Other Government documents, drawings and publications. The following ot

8、her Government documents, drawings, and publica- tions form a part of this specification to the extent specified herein. DRAWINGS U.S. Marine Corps 855001B0000 -SIXCON Shipping Frame CODE OF FEDERAL REGULATIONS (CFR) 4 9CFR4 5 1 -Testing and Approval of Cargo Containers (Copies of specifications, st

9、andards, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following documents form a part of this specification to the extent s

10、pecified herein. The issues of the documents which are indicated as DoD adopted should be the issue listed in the current DoDISS and the supplement thereto, if applicable. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-F-27437 83 779770b 042

11、2283 L 1 MIL-F- 29 41 9 (MC) AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) I IS0 668 -Freight Containers - External Dimensions and Ratings IS0 1161 -Series 1 Freight Containers -Corner Fittings -Specification IS0 1496/I -Series 1 Freight Containers - Specification and Testing - Part I: General Cargo

12、Containers (Applications for copies should be addressed to the American National Standards Institute, 1430 Broadway, New York, New York 10012. ) AMERICAN WELDING SOCIETY (AWS) , AWS D1.l -Structural Welding Code, Section 5, Qualification - Welding Inspection Manual 1 (Applications for copies should

13、be addressed to the American Welding Society, 2501 North West 7th Street, Miami Florida 33125.) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) Boiler and Pressure Vessel Code, Welding Qualification, Section IX ;. (Applications for copies should be addressed to the American Society of Mechanical Eng

14、ineers, 345 East 4th Stree, New York, 1 New York 10017.) 1 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) I ASTM D3951-82 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsy

15、lvania 19103.) text of this specification and the references cited herein, the text of this specification shall take precedence. 2.3 Order of precedence. In the event of a conflict between the 3 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F

16、-29 419 (MC) 3. REQUIREMENTS 3.1 First article. Unless otherwise specified (see 6.21, the contractor shall furnish three shipping frames for IS0 testing. The first article shall be manufactured using the same methods, procedures, and tooling proposed for production. Approval of the first article by

17、the procuring activity shall not relieve the contractor of the obligation to supply equipment conforming to this specification. Changes or deviations in production units from the approved first article baseline shall require written authorization by the procuring activity. 3.2 Materials. Material us

18、ed in fabrication of the shipping frame shall be as specified on Drawing No. 855001B0000. Materials shall be free of defects and imperfections that might affect the serviceability and appearance of the finished product. Substitute material shall not be utilized prior to written authorization by the

19、procuring activity. Materials not specified shall be selected by the contractor and.shall be subject to all provisions of this specification. 3.3 Design and construction. The shipping frame shall be fabri- cated and assembled in accordance with Drawing No. 855001B0000 and as specified herein, 3.3.1

20、Cargo netting tiedowns. One cargo net conforming to MIL-N-27444, type HCU-l5/C and four cargo tiedowns conforming to MIL-T-27260, type CGU-1/B, 6,000 pound capacity shall be pro- vided with each shipping frame. 3.3.2 Connectors. Three horizontal connectors and two vertical connectors shall be provid

21、ed with each shipping frame. 3.3.3 Safety approval plate. Necessary actions as prescribed in 49CER451 (see code of Federal Regulations) shall be accomplished to obtain approval of the containers by an appropriate Convention for Safe Containers (CSC) approval authority (see 49CFR451, Subpart B - “App

22、roval of New Containers“) and the required CSC safety approval plate shall be provided and affixed to the frame as prey scribed in 49CFR451, C - “Safety Approval Plate“. The notice of approval received from the approval authority which authorizes the attachment of CSC safety approval plates shall be

23、 furnished to the contracting officer within 30 days of receipt by the contractor. The contractor shall also provide a certificate to the contracting officer stating the serial number, model number, and any pertinent manufacturing identification numbers of the shipping frames that are covered under

24、a specific notice of approval. 3.3.4 Welding and welders. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-29419 (MC) 3.3.4.1 Weldinq. The shipping frame shall be welded in accordance with Drawing No. 855001B0000. Welding shall meet the requir

25、ements of MIL-W-8611. The surface of parts to be welded shall be free from rust, scale, paint, grease, or other foreign matter. Spot, tack, or intermittent welds shall not be permitted unless otherwise cited in Drawing No. 855001B0000. Weld penetration shall be such as to provide transference of max

26、imum design stress through the base metal juncture. Fillet welds shall be provided when necessary to reduce stress concentration. All finished weldments shall be straight and true in accordance with good shop practice. Faulty weld- ments shall be corrected by welding only. Peening shall not be utili

27、zed to correct faults. Weld spatters shall be removed. All parts shall be properly aligned and meshed and operable without interference, tight spots or other irregularities. 3.3.4.2 Welders. All welders shall be qualified for the types of welds required in the fabrication of shipping frames. Before

28、assigning any welder to welding work, the contractor shall provide the contracting officer with certification that the welder has passed qualification tests as prescribed by either of the following listed codes for the type of welding operation to be performed and that such qualification is effectiv

29、e as defined by that particular code. AWS D1.l, Structural Welding Code, Section 5. Qualification - Welding Inspection Manual Boiler and Pressure Vessel Code, Welding Qualifications, Section IX (ASME) 3.3.5 Castings and forgings. Castings and forgings shall be manufactured in accordance with Drawing

30、 No. 855001B0000. All castings shall be sound and free from patching, inclusions, misplaced coring, warping, or any other defect that reduces the castings ability to perform its intended function. Forgings shall be uni- form in quality and condition, and shall be free from tears, cracks, seams, laps

31、, internal ruptures, imbedded scale, segre- gation and other defects. 3.3.6 Bolted and pinned connections. Bolt and pin holes shall be accurately punched or drilled and shall have the burrs removed. Washers or lockwashers shall be provided in accordance with good commercial practice and all bolts, n

32、uts and screws shall be tight. 3.3.7 Machine work. Where machined surfaces are required to be heat treated, hardened, finish grounded, plated or coated, the part dimensions, as specified in Drawing No. 855001B0000, shall be main- tained. 5 Provided by IHSNot for ResaleNo reproduction or networking p

33、ermitted without license from IHS-,-,-MIL-F-29419 (MC) 3.3.8 Metal fabrication. Metal used in the fabrication of the shipping frames shall be free from kinks and sharp bends. The straightening of material shall be done by methods that will not cause injury to the metal. Flame cutting, using a tip su

34、itable for the thickness of the metal, may be employed instead of shear- ing or sawing. Reentrant cuts may be made with controlled means in order to ensure uniformity of size and shape. Heated metal shall be allowed to cool slowly. 3.3.9 Interchangeability. Shipping frames of the same classifi- cati

35、on, furnished under any specific contract, shall be physically and mechanically identical. They shall meet the applicable requirements specified in IS0 668, 1161, and 1496/I. 3.4 Environmental requirements. Shipping frames shall withstand, without cracking, corroding, peeling of paint, or loss of fu

36、nc- tionality, humidity resistance, low temperature (-25OF) and high temperature (160OF) when tested as specified in 4.5.9. 3.5 Painting. The shipping frame shall be painted as specified on Drawing No. 855001B0000 and MIL-E-52798. Color shall be as specified in 6.2. 3.6 Marking/serialization. 3.6.1

37、Shipping frame. The shipping frame shall be marked and serialized as specified on Drawing No. 855001B0000. 3.6.2 - Parts and components, Parts and components shall be marked in accordance with MIL-STD-130. 3.6.3 Identification plate. The shipping frame identification plate shall be in accordance wit

38、h Drawing No. 8550010000. 3.7 Workmanship. All parts, components, and assemblies of the shipping frame, including castings, forging, molded parts, stamp- ings, seals and sealing agents, machined surfaces, and welded parts shall be clean and free from any defects that will reduce the capability of th

39、e shipping frame to meet the requirements specified herein. Any components and assemblies which have been repaired or modified to overcome deficiencies shall not be used without prior approval of the contracting officer. External surfaces shall be free of burrs, slag, sharp edges and corners where s

40、harp edges and corners are required. 4, QUALITY ASSURANCE PROVISIONS 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-F-274L7 81 m 7797706 O422285 7 MIL-F-29419 (MC) 4.1 Responsibility for inspection. Unless otherwise specified in the contract

41、 or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suit- able for the performance of the inspection requireme

42、nts specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to the prescribed requirement. specified herein are class

43、ified as follows: 4.2 Classification of inspections. The inspection requirements (a) First article inspection (see 4.3) (b) Quality conformance inspection (see 4.4) (c) Packaging (see 4.6) 4.3 First article inspection and testing. First articleinspec- tion shall consist of the examinations and tests

44、 specified in Table I. Failure to pass any test shall be cause for rejection. Three SIXCON shipping frames shall be used for testing. TABLE I. Inspection and test requirements Inspection Requirement Test First Quality Paragraph Paragragh Article Conformance Material Certification 3.2 4.5.1 X X Const

45、ruction 3.3 4.5.2 X X Painting 3.5 4.5.3 -X X Marking/Serialization 3.6 4.5.4 X X Workmanship 3.7 4.5.5 X X Welds 3.3.4 4.5.6 X X Castings 3.3.5 4.5.7 X X Forgings 3.3.5 4.5.8 X X Environmental Test 3.4 4.5.9 X IS0 Testing 3.3.3 4.5.10 X Packaging 5 4.6 X 4.4 Quality conformance inspection. Quality

46、conformance inspection shall consist of the examinations and tests specified in Table I. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-29419 (MC) 4.4.1 oLot size. An inspection lot shall consist of all shipping frames produced during an ide

47、ntifiable production period and sub- mitted at one time for acceptance. Production period shall be 1 month, 4.4.2 Sampling for inspection. Sampling for inspection from each inspection lot shall be in accordance with inspection N-II-S of MIL-STD-105. The Acceptance Quality Level (AQL) shall be 0.65 p

48、ercent for critical defects, 1.0 percent for major defects and 2.5 percent for minor defects. 4.4.3 Inspection failure. Failure of a production shipping frame to meet any of the requirements specified herein during and as a result of the specified inspections and tests shall be cause for refusal by

49、the Government to continue the acceptance of production shipping frames until evidence has been provided by the contractor that corrective action has been taken to eliminate the deficiencies. Correction of such deficiencies in shipping frames previously accepted and produced under the contract shall be accomplished by the contractor at no cost to the Government. Any deficiencies found as a result of any production inspection will be consi