NAVY MIL-G-82242 D-1987 GLOVE SHELLS RADIOACTIVE CONTAMINANTS PROTECTIVE《防止放射污染的嵌入式手套》.pdf

1、MIL-G-2242D 4 06 O4Ob78 2 MIL-G-82242D 4 February 1987 - SUPERSEDING MIL-G-82242C 12 .June L978 MILITARY SPECIFICATION GLOVE SHELLS, RADIOACTIVE CONTAMINANTS, PROTECTIVE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This spec

2、ification covers the requirements for unsupported dipped rubber gloves, made of natural latex. * 1.2 Classification. The gloves shall be of one type and shall be procured in the following sizes and lengths as specified (see 6.2): Schedule of sizes Lengths 8-9-10-11 12 and 18 inch 2. APPLICABLE DOCUM

3、ENTS * 2.1 Government, documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those .listed in the issue o

4、f the Department of. Defense Index of Sp.ecif ications and Standards (DODISS) and supplement thereto , cited inthe solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge

5、, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC/NA FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release

6、; distribution is unlimited. K THIS DOCUMENT CONTAINS PAGES. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-G-Z242D 84 9999906 0906799 4 MI i, -G-8 2 2 4 2 D b SPECIPICATIONS FEDERAL XN-P-7 1 - Pallet, Ma

7、terial Handling, Wood Stringer PP P-B-6 36 - Boxes, Shipping, Fiberboard Construction, 2-Way and I TARY MIL-P-15011 - Pallet, Material Handling, Wood, Post Construction incorrect; illegible; of improper size, location, sequence, or method of application. Preservation shall he level- A or C as specif

8、ied (see 11 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-G-822LI2D 8LI m 7779706 OLIO6807 3 W MIL-G-82242D 5.1.1.1 Unit packaging. Each pair of gloves shall be inserted. in a flat style, polyethylene film bag, of 0.00125 inch thick (+ 25 per

9、cent tolerance). The polyethylene bag shall be formed with heat sealed Seams that are straight, continuous, and parallel to each other and the formed edges of the bag. The bag may be fabricated from polyethylene film tubing or sheeting. The final closure of the bag shall be heat sealed, with the sea

10、l made as close as possible to the open end. Prior to or during the closure operation excess air within the bag shall be expelled. f 5.1.1.2 Intermediate packaging. Six (6) pairs of gloves of one size and length only, unit packaged as specified in 5.1.1, shall be packaged in a paperboard box of suff

11、icient size to meet the requirements of 5.2 without excessive voids in the shipping container. 5.1.2 Level C, Gloves shall be preserved to afford adequate protection against physical damage during shipment from the supply source to the first receiving activity. The contractor may use his standard pr

12、actice when it meets this requirement. 5.2 Packing. Packing shall be level A, , or C as specified (see 6.2). * 5.2.1 Level A. Six (6) intermediate boxes (thirty-six (36) pairs of gloves) of one size and length only and preserved-packaged as specified in 5.1, shall be packed in a fiberboard shipping

13、container conforming to type CF, class weather resistant, variety DW, style RSC, grade V15C of PPP-B-636. Level A boxed gloves shall be packed flat three in length, one in width, and two in depth within the shipping container. Inside dimensions of each shipping container shall approximate 16-1/4 inc

14、hes in length, 12-3/4 inches in width, and 7-1/8 inches in depth. Approximate dimensions are Eurnished as a guide only. Each shipping container shall be closed in accordance with method III, waterproofed in accordance with method V, and reinforced as specified in the appendix of PPP-B-636. Toward th

15、e end of the contract, or when there are less than the required amount per container of the same size, mixed sizes may be packed within the same shipping container. * 5.2.2 Level B. Six (6) intermediate boxes (thirty-six (36) pairs of gloves) of one size and length only and preserved-packaged as spe

16、ciied in 5.1, shall be packed in a fiberboard shipping container conforming to type CF, class domestic, variety DW, style RSC, grade 275 of PPP-B-636. Level A boxed gloves shall be packed flat, three in length, one in width, and two in depth within the shipping container. Inside dimensions of the fi

17、berboard shipping container shall approximate 16-1/4 inches in length, 12-3/4 inches in width, and 7-1/5 inches in depth. Approximate dimensions are furnished as a guide only. Each shipping container shall be closed in accordance with method II as specified in the appendix of PPP-B-636. Toward the e

18、nd of the contract, or when there are less than the required amount per container of the same size, mixed sizes may be packed within the same shipping container. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. .- MIL-G-Z242D 4 99999Oh 040h8LO T

19、5.2.3 Level C. Gloves, packaged as specified in 5.L, shall be packed in a manner to insure carrier acceptance and safe delivery at destination at the lowest transportation rate or such supplies. The quantity per shipping container shall be the same as that normally used by the contractor for retail

20、distribution. Containers shall comply with the US Postal Service Manuai, Uniform Freight Classification Rules, or National Motor Freight ClassiEication Rules as applicable. 5.3 Marking. In addition to any special marking required by the contract or order, shipping containers shaLl be marked in accor

21、dance with MIL-STD-129. 5.361 Labels, mixed sizes. Each shipping container, packed with mixed sizes only, shall have securely attached to the ends and side, directly under the printing or stenciling, a white paper label 5 by 4 inches with the words “MIXED SIZES“ plainly stamped or printed thereon an

22、d under these words shall be legibly stamped or printed the correct quantity and sizes contained therein. * 5.4 Palletization. When specified (see 6.2) item packed as specified shall be palletized on a 4-way entry pallet in accordance with load type 1A of MIL-STD-147. Each prepared load shall be bon

23、ded with primary and secondary straps in accordance with bonding means Cy K, and L or O OK P. Pallet pattern shall be in accordance with the appendix of MIL-STD-147. The pallet shall be 4-way, Type IV, V or VIII, Class 1, Style A, Size 2, wood group I, II, III, or IV, Grade A of NN-P-71, or 4-way, S

24、tyle 1, Size A, Type I, Class 1 of wood group I, II, III, or IV, Grade A of MIL-P-15011. Interlocking of loads shall be effected by reversing the pattern o each course. If the container is of a size which does not conform to any of the patterns specified in MIL-STD-147, the pallet pattern used shall

25、 be approved by the contracting officer. 6. NOTES 6.1 Intended use. The gloves covered by this specification are intended to be used by-military personnel for their protection when working in the presence of low level radioactive contamination. This glove is required to be worn over a cotton insert

26、along with the other applicable items of protective clot hing * 6.2 Ordering - data. Procurement documents should specify the following: a, Title, number, and date of this specification. b, Sizes and lengths required (see 1.2). c. Selection of applicable levels of packaging and packing (see 5.1 and

27、5.2). * d, When first article inspection is required (see 3.2), the item will be tested and should be a first article sample. The contracting officer should include specific instructions in acquisition documents regarding arrangement for examinations, quantity, and testing and approval. When palleti

28、zation is required (see 5.4). e, 6-3 Samples and molds. For access to samples and the standard molds, address the procuring office issuing the invitation OK bids. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-2242D 84 777770b 04068LL L MIL-G-

29、82242D * 6.4 Die C. Dies conforming to BNSIIASTM TM 412 may be obtained rom the following suggested sources: a. Boston Cutting Die CO., 50-52 Preeport St., Boston, MA 02122 b. Philadelphia Consolidated Die, 327 Race St., Philadelphia, PA 19103 In case of dispute, dumbell specimens shall be cut from

30、paper or oil board and measured to determine conformance to the Die C measurements listed in ANSI/ASTM TM 412. * 6.5 Changes from previous issue. The margins of this specification are marked with an asterisk to indtcate where changes (additions, modifications, corrections, deletions) from the previo

31、us issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of tne marginal notations a

32、nd relationship to the last preview issue. * 6.6 Subject term (key words) listing. Color, orange yellow Latex, natural Radioactive contaminants protective Rolled bottom edge Style, four finger and thumb Utility Custodian: Navy - NU Review Activity: Navy - SHY MS DLA - CT User Activity: Navy -AS, OS,

33、 My CG Preparing activity : Navy - NU Project No. 8415-0395 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-G-82242D 4 779790b 0406832 3 MIL-G-82242D 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

34、m IHS-,-,-r MIL-G-82242D 4 7777706 0406813 5 0“ 3“ 64 - 1 Figure 3, - RADIATION SYMBOL 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-82242D FIGURE 3 APPARATUS FOR POROSITY TEST 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-