NAVY MIL-J-82299 C-1988 JACKET EXTREME COLD WEATHER IMPERMEABLE《用于极冷环境的防渗夹克》.pdf

1、- SUPERSEDING MIL-J-82299B(NU) 7 August 1981 MILITARY SPECIFICATION JACKET, EXTREME COLD WEATHER, IMPERMEABLE sbq This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Departments and Agencies of the Departm

2、ent of Defense. a 1. SCOPE This specification covers the requirements for an impermeable extreme l*l -opa* col weather insulated jacket constructed of a coated nylon twill and lined with uncoated nylon taffeta covered plastic foam. 1.2 Classification, The jacket shall be of one type only and in the

3、following sizes (see 6.2). * 1.2.1 Sizes. Small, Medium, Large, X-Large,-XX-Large 2. APPLICABLE DOCUMENTS O * 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified h

4、erein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any perti

5、nent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of

6、this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. THIS DOCUMENT CONTAINS 39 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL V-B-87 1 V-F-106 V

7、-T-280 V-T-295 NN-P-71 DDD-L- 20 MILITARY MIL-B-37 1 MIL-F-495 MIL-C-3735 MIL-F-10884 MIL-P-12420 MIL-P-15011 MIL-G-16491 MIL-B-17757 MIL-C-19699 MIL-C-19759 MIL-C-21852 MIL-B-41826 STANDARDS FEDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 - Button, Sewing Hole, and Button, Staple (

8、Plastic) - Fasteners, Slide, Interlocking - Thread, Cotton Gimp, Buttonhole - Thread, Nylon - Pallet, Material Handling, Wood, Stringer - Label; for Clothing, Equipage and Tentage (General Construction, 2 Way and 4 Way (Partial) Use) - Braid, Textile, Tubular - Finish, Chemical, Black, for Copper Al

9、loys - Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted - Fasteners, Snap - Plastic Material, Cellular, Elastomeric - Pallet, Material Handling, Wood, Post Construction, 4 Way Entry - Grommet, Metallic - Boxes, Shipping, Fiberboard (Modular Sizes) - Cloth, Coated (Nylon Taffeta) - Cloth, Coated, Twi

10、ll, Nylon (Low Count) - Cloth, Nylon, Taffeta - Batting, Synthetic Fibers: Polyester (Quilted and Unquilted) - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit Loads Attributes (Copies of specifications, standards

11、, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. ) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents,

12、 drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-822

13、99C(NU) LAWS AND REGULATIONS U.S. POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) * 2.2 Other publications. The following document(s) form a part of this specification to the extent specifi

14、ed herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents whic

15、h is current on the date of the solicitation, NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applicati Association, 20036-1404.) ons for copies should be addressed to the American Trucking ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC U

16、NIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606-5808.) THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades

17、for Buttons Department of Defense Standard Shades for Sewing Threads (Application for copies of color cards should be addressed to the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016.) * 2.3 Order of precedence. In the event of a conflict between the text of this spe

18、cification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are sole

19、ly for guidance and information to the contractor (see 6.3). Variations from this specification may appear-in the sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 an

20、d 6.2). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3 Material. * 3.3.1 Basic material. The basic material for the outer shell shall be chloroprene coated nylon twill conforming to type I of MIL-C-19759 (see 4.4.1). 3.3.1.1 Binding. The mater

21、ial used for the binding shall be of the basic material specified in 3.3.1, bias-cut on a 45 (+5) degree angle in strips 1-1/8 to 1-3/8 inches wide. The ends of the strrps shall be joined by seam type SSa-1, stitch type 301, with 8-10 stitches per inch. The seams shall finish 1/8 to 3/16 inch wide a

22、nd shall be spread open. 3.3.2 Taffeta, nylon, coated. The material for the pockets and lining gussets shall be chloroprene coated nylon taffeta conforming to type I of MIL-C-19699. * 3.3.3 Corduroy. The material for the topcollar and topcollar stand shall be 100% cotton or cotton/polyester blend of

23、 not less than 80% cotton. It shall have a minimum of eight wales per inch and weigh not less than 8.0 oz/sq yd. The cloth shall be fast dyed (no sulfur) dark green, black, or olive drab and after treated with a durable water repellent impregnant. As a limit of acceptability, the dyed and treated cl

24、oth shall show good colorfastness to crocking and perspiration (see 4.4.1). 3.3.4 Quilted lining and interlining assembly. The quilted lining and interlining assembly of the jacket shall consist of a middle layer of expanded plastic foam covered on both sides with an uncoated nylon taffeta, conformi

25、ng to the requirements of 3.3.4.1. 3.3.4.1 Plastic foam, cellular, elastomeric. The material for the middle layer shall be plastic foam, 5/32 inch thickness, conforming to type II, class 6 of MIL-P-12420, except as follows: a. The minimum density shall be 3.0 lbdcubic foot. b. The maximum compressio

26、n deflection shall be 3.5 psi. c, The temperature for pefforming the low temperature flexibility test shall be minus 30F + 2 F. d. The buoyancy shall not be less than 54.0 pounds per cubic foot when tested as specified in 4.4.1. NOTE: To form rolls of plastic foam for quilting when plastic foam is s

27、upplied in sheet form, the raw edges of each plastic foam piece shall be abutted and joined across the width with a 1 to 1-1/2 inch wide strip of pressure sensitive tape. * 3.3.4.2 Nylon, taffeta, uncoated. The material for the cover layer (top and bottom) shall be an uncoated nylon taffeta conformi

28、ng to MIL-C-21852, type III. The color shall match Green 3406, identified under piece Number 6-60. The material may be either dyed or undyed for the bottom ply of the back, front, and sleeve linings and for the top and bottom plies of the collar, back, and front interlinings. 3.3.4.3 Quilting, The t

29、hree layers of lining and interlining assemblies shall be quilted in accordance with the dumbbell quilt pattern shown in Figure 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-2277C LI M 7779906 OLIO7350 7 M t i MIL-J-82299C(NU) 1 of MIL-B-41

30、826 or Figure 2 of this specification. When the large dumbbell pattern in MIL-B-41826 is used, all raw edges shall be overedged (see operation 11). The quilting thread shall be nylon conforming to type I, size A, of V-T-295. . Colorfastness of thread shall be as specified in 3.3.5.1. The colok of th

31、e thread shall approximate the shade of the dyed nylon taffeta. Thread may be either natural shade or white for quilting the underside of the lininglinterlining assembly. The stitch type shall be 301 using 6 to 8 stitches per inch. * 3.3.5 Thread. The thread for seaming and stitching the jacket shal

32、l be nylon, conforming to type III, sizes B and E of V-T-295. The color shall be olive drab shade S-1, cable number 66022 in accordance with the Department of Defense Standard Shades for Sewing Threads. As an alternate, and where applicable, type II, size B and E may be used for the needle thread an

33、d type i, size B or E may be used for the bobbin thread. * 3.3.5.1 Colorfastness. The dyed thread shall show colorfastness to laundering equal to or better than the standard sample when tested as specified in V-T-295. As a limit of acceptability or when no standard sample is available, the dyed thre

34、ad shall show a minimum of Igood1l fastness to laundering when tested as specified in V-T-295. m 3.3.6 Gimp. The gimp for reinforcing the buttonhole shall be thread, cotton gimp conforming to type I or II, size No. 8 of V-T-280. The color shall approximate the shade of the basic material. * 3.3.6.1

35、Colorfastness. As a limit of acceptability, the dyed gimp shall show a minimum of “good“ fastness to laundering when tested as specified in V-T-280 * 3.3.7 Slide fastener. The slide fastener for the front closure shall be interlocking, long tab pull, natural brass chain, conforming to type IV, style

36、 8, size MH of V-F-106. As an alternate, the slide fastener shall be molded plastic individual element or continuous chain conforming to type I, style 15, size MHS, long tab pull of V-F-106. The color of the plastic slide fastener components shall be black. The slide fastener tape shall approximate

37、the shade of the basic material and shall be cotton, synthetic or a combination of both. When applicable, all brass components of the slide fastener shall be furnished by the same supplier. Lengths shall be such that the top stop of the slide fastener shall be set 1/4 to 1/2 inch from the finished n

38、eck seam. 3.3.8 Snap fastener. The snap fasteners for the pockets and hood attachment loop shall be regular wire spring clamp type conforming to style 2, 24-line, finish 2, conforming to MIL-P-10884, * 3.3,9 Buttons. The buttons for the front closure shall be 34-line and the buttons for the collar e

39、xtension tab closure shall be 24-line, plastic, conforming to type II, class D, style 20 and 21 with stud conforming to . V-B-871. The color shall be olive green BP, cable number 62016 in accordance with the Department of Defense Standard Shades for Buttons. 3.3.10 Cuffs. The cuffs shall be wool, kn

40、itted, dyed to approximate the shade of basic material, conforming to type I, class 2, size 1 of MIL-C-3735, except that the shrink resistant treatment and colorfastness to light and dry cleaning shall not apply. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

41、from IHS-,-,-_I -_ - MIL-J-82299C 84 W 7797906 0407353 7 MIL-J-82299C(NU) 3.3.11 Braid. The braid for the button loops and tie cord shall be solid tubular cotton conforming to type IV or V, class 1 of MIL-B-371, except that colorfastness to bleaching shall not apply. The color shall approximate the

42、shade of the basic material. 3,.3.12 Grommets. The grommets and washers for the jacket hem shall be brass conforming to type 1, size No. O, class 3 of MIL-G-16491, 3.3.13 Eyelet. The eyelet for the sleeve extension piece shall be 1/8 to 3/16 inch ID, brass, with a black chemical finish conforming to

43、 MIL-F-495 (see 4.4.1). As an alternate, a machine sewn eyelet may be used. * 3.3.14 Labels. Each jacket shall have a combination identification and instruction label and a separate size label, conforming to the requirements of 3.3.14.1 and 3.3.14.2. The printing shall show fastness to laundering. *

44、 3.3.14.1 Combination label. Each jacket shall have a combination identification/instruction label conforming to type VI, class 15 of DDD-L-20, and shall bear the following inscription: 1 JACKET, EXTREME COLD WEATHER, IMPERMEABLE BASIC FABRIC: 100% NYLON QUILTED LINING: PLASTIC FOAM AND NYLON NAME O

45、F CONTRACTOR: NAME OF MANUFACTURER: CONTRACT NO: DLA-100-00-0-0000 (EXAMPLE) (IF OTHER THAN CONTRACTOR) Cleaning Jacket should be laundered with water temperature below 140F Each jacket shall have a size label conforming to type (60C) and tumble dried below 160F (71C). * 3.3.14.2 Size label. VI, cla

46、ss 2 of DDD-L-20, and shall bear the following inscription: SIZE : MEDIUM (EXAMPLE) STOCK NUMBER: 8415-00-000-0000 (EXAMPLE) * 3.4 Design. The impermeable jacket shall have an outershell of coated nylon fabric with the coating on the underside. The body and sleeves shall be lined with a layer of buo

47、yant plastic foam quilted on both sides with uncoated nylon taffeta cloth. The back and chest shall have an additional layer of quilted material. The jacket shall be hip length with a front slide fastener closure covered with a buttoned extension flap. The collar shall be lined with corduroy and int

48、erlined with foam and secured by a buttoned collar tab closure. The sleeves shall have knitted cuffs. A tie-cord shall be threaded through grommets into a tunnel-hem at the bottom. A snap fastener flap welt pocket shall be positioned on each front. Four eyelets shall be inserted or machine sewn at i

49、nside bottom of each sleeve. A strap with snap fastener on one end shall be attached at outside center back of collarstand to attach cold weather hood. 3.4.1 Figures. Figures are furnished for information purposes only. When inconsistencies exist between the specification and the figures, the 6 P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-82299C q m 7979906 Og07352 O specification shall govern.