NAVY MIL-L-1130 E-1990 LANTERN ELECTRIC STORAGE BATTERY FLOODLIGHTING HAND CARRIED《手抬式带电的蓄电池泛光灯照明航标灯》.pdf

1、MIL-L-LL3OE 62 = 9979406 0366280 3 M IINC“D1 MIL-L-113OE 26 Januarv 1990 SUPERSEDING 14 August 1963 MIL-L-1130D MILITARY SPECIFICATION LA“, ELECTRIC, STORAGE BATERY, FLOODLIGHTING, HAND CARRIED This specification is approved for use by all Department and Agencies of the Department of Defense. 1. SCO

2、PE 1.1 Scope. This specification covers hand carried, flood lighting, storage battery powered electric lanterns, 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified

3、herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MUIITARY MIL-E-917 MIL-E-2036 Electric Power Equipment, B

4、asic Requirements (Naval Shipboard Use) Enclosures for Electric and Electronic Equipment, Naval Shipboard I 1 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed tm Commanding Officer, Naval Sea Systems

5、 Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document improvement Proposal (DD Form 14%) appearing at the end of this document or by letter. I 1 AMSC NIA FSC 6230 DISTRIBUTION STATEMENT A. Approved for public release; distribution

6、is unlimited. Licensed by Information Handling ServicesMIL-L-LL30E b2 377970b 0366281 5 MIGG1130E MIL-F-3222 MIGP-15024 MIGP-15024/5 MIGM-15071 DOD-B-15072 DOD-B-15072B MIL-F- 16377 Floodlights and Lanterns, Packaging of Plates, Tags and Bands for Identification of Equipment Plates, Identification M

7、anuals, Technical; Equipment and Systems Content Requirements for Batteries, Storage, Lead-Acid, Portable; General Specification for (Metric) Battery, Storage, Lead-Acid, Portable, Type 2V - 20 - AH - 4D - A (Metric) Fixtures, Lighting; and Associated Parts; Shipboard Use, General Specification for

8、STANDARD FEDERAL FED-STD-HB Screw-Thread Standards for Federal Services MILITARY MIL-STD-105 MS 15607 MS 16656 Sampling Procedures and Tables for Inspection by Attributes Lamps, Incandescent PAR-46, Screw Terminal Switch, Toggle, Single Pole, Single Throw (Copies of specifications and standards requ

9、ired by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 23 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for as

10、sociated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When

11、specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3 and 6.4). 2 Licensed by Information Handling ServicesMIL-Gl130E 3.2 General requirements. 3.2.1 Materials and design. The materials and configuration of the lantern shall be as specified her

12、ein and on figures 1 and 2. Materials not definitely specified shall be of the quality best suited for the purpose intended. Steel parts, where used, shall be protected against corrosion. 3.2.2 Construction. The complete lantern shall be compact, simple in construction, and as rugged as practicable.

13、 3.23 Finishing. 3.23.1 Cleaning. Cleaning shall be in accordance with MIL-E-917. 3.23.2 Priming. All metal parts shall be primed in accordance with the best commercial practice. (This operation may be combined with the cleaning specified in 3.2.3.1.) 3.233 Enamel. All exterior metal surfaces of lan

14、tern shall be given a final finish of a high temperature baked-on gray enamel of a good commercial grade which will not chip, scratch or mar (see 3.3.3.5). 33 Detail requirements, 33.1 Metal parts. Except for associated fastening hardware, all metal parts shall be made of aluminum and of a thickness

15、 as will assure the required strength and stiffness to withstand rough handling. The battery case cover shall have a minimum thickness of 0.080 inch. Grade of aluminum used shall be the manufacturers choice. 33.2 Size. The lantern shall not exceed the dimensions shown on figure 1. 333 Battery ase. T

16、he case shall be constructed to receive four battery cells (see 3.3.13). 333.1 The interior shall be subdivided into four compartments, each of which shall accommodate one battery cell. Clearance shall be provided between the battery cell and surrounding walls in order that the cells may be easily r

17、emoved. 333.2 Means for ventilation shall be provided in the case (see 3.3.4). 3333 Two drain holes approximately 1/4 inch in diameter shall be provided in the bottom of the case, one near each end. 333.4 The case shall be provided with four windows of sufficient area and so located that the positio

18、n of the indicating balls of each battery cell may be observed when within 1 inch of the water level line of the cell. The windows shall be made of a clear plastic material of adequate strength and shall be secured to the case. 3 Licensed by Information Handling Services MIL-L-LL30E b2 m 77777Ob 036

19、6283 7 m MILL-1 130E 333.5 All interior surfaces of the battery case, including dividers and cover shall be coated with a black acid-resisting paint of a good commercial grade. 33.4 Battery case cover. The cover shall be s constructed that when secured to the battery case, it will provide the drip-p

20、roofness specified in 3.3.8, yet permit gases to escape through eight breather holes (5/16 inch diameter minimum) protected by a 3/4 inch flange. 33.4.1 The interior of the cover shall be provided with a filler block, adequately attached thereto to prevent movement of the battery cells and consequen

21、tly short-circuiting of the terminals against the cover. This filler block shall be made of 2 plastic material suitable for the purpose intended. 33.4.2 The cover shall be simply and positively attached to the battery case (see figure 1). 33.5 Threads. Threads shall conform to FED-STD-HZ. 33.6 Handl

22、e. The lantern shall be provided with a carrying handle, arranged so that the complete unit may be conveniently carried with the lamp housing clamped in any position. The handle may be secured to the cover as shown on figures 1 and 2. 33.7 Quadrant. The quadrant and associated parts shall be so cons

23、tructed as to provide vertical adjustment of the light beam axis from approximately 30 degrees below to approximately 60 degrees above the horizontal. A simple device shall assure positive clamping in any position. 33.8 Degree of enclosure. The complete lantern shall be drip-proof. This degree of en

24、closure requires that solid or liquid material falling from any direction up to a maximum angle of 45 degrees from the vertical shall be effectively excluded from the interior of the case and the lamp housing assembly. 33.9 Bolts, nuts, screws, washers and so forth. Unless othenirise specified in th

25、e contract or order (see 6.2), all hardware shall be of a good cornmercial grade. Steel (CRES excepted) shall be zinc plated. 33.10 Plating. Zinc plating shall be used on unpainted parts, such as fastening hardware, to prevent corrosion. 33.11 Identification and information. 33.11.1 Identification p

26、late. An identification plate in accordance with MIL-P-15024 and MIL-P-15024/5 shall be attached to the battery case. This plate shall include the name of the item, symbol number, specification number, federal stock number and the contractors name or trademark. 4 a r 4 a e a Licensed by Information

27、Handling ServicesMIL-L-113OE 33.11.2 Label. A label, containing a wiring diagram as shown in figure 3 and in accordance with MILF-16377, shall be attached to the inner surface of the cover. 33.12 Lamp housing. The lamp housing shall be of a size that will accommodate the sealed beam lamp specified i

28、n 3.3.14. The thickness of material shall provide protection of the lamp against rough handling. The lamp, cushioned by a rubber gasket, shall be securely held to the lamp housing by a retaining ring. A device such as a screw and captive nut may be used for tightening the retaining ring. The gasket

29、shall be a good commercial grade rubber tape at least 1 inch wide and shall completely encircle the lamp to provide a drip-proof seal and to protect the lamp against excessive vibration and rough handling. 33.13 Battery. When batteries are specified (see 6.2), they shall be comprised of four cells,

30、type 2V-20AH-4D-A, in accordance with DOD-B-i5072 and DOD-B-15072/3. 33.14 Lamp. Unless otherwise specified in the contract or order (see 6.2), lamps, industry number 4524 in accordance with MS 15607 shall be furnished. 33.15 Cable. Unless otherwise specified (see 6.2), the cable interconnecting the

31、 lamp housing and battery case shall be SJO(or Ssr)-18/2, UL, approved. Rubber grommets of a good commercial grade shall be used to prevent the entrance of moisture where cable enters lamp housing and battery case cover. 33.16 Connecting wires. The connecting wires shall be a good commercial type, U

32、L approved, of not less than 950 circular mils. All connecting wires liable to chafiig and grounding shall be suitably insulated and coated with a black acid-resisting paint. 33.16.1 Wire terminals. Closed lead coated wire terminals, UL approved, shall be provided for connecting to the battery termi

33、nals and to the lamp. 33.17 Switch. The toggle switch shall be a UL approved type conforming to MS 16656. A rubber boot shall be used to prevent the entrance of moisture into the switch. 33.18 Dielectric strength. There shall be no evidence of breakdown (see 4.6.2). 33.19 Insulation resistance, The

34、insulation resistance between all current-carrying and non- current-carrying parts shall be not less than 100 megohms (see 4.6.3). 33.20 Salt spray, Equipment made of steel or aluminum, subject to weather deck usage, shall satisfactorily withstand the salt spray test (see 4.6.4). 33.21 Weight- The t

35、otal weight of the lantern, complete with batteries, ready for operation, shall not exceed 30 pounds. 5- Licensed by Information Handling ServicesMIL-L-LL30E 62 W 9979906 03bb25 2 W MILL1 130E 3.4 Repair parts. When specified (see 6.2), repair parts shall consist of two lamps for each complete lante

36、rn. 3.5 Manuals. A manual in accordance with type I of MIL-M-15071 shall be furnished with each lantern. 3.6 Workmanship. Workmanship shall be first class in every respect. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order

37、 (see 6.2), the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specif

38、ied herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. Ai

39、l items must me& all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsib

40、ility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accepta

41、nce of defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: (a) First article inspection (see 4.3) (b) Quality conformance inspection (see 4.4). 43 First article inspection. First article inspection shall consist of the examin

42、ation and tests specified in 4.5 and 4.6. Production shall not be started until the preproduction inspection report has been approved by the command or agency concerned. 4.4 Quality conformance inspection, 4.4.1 Lot A lot shall consist of all lanterns offered for delivery at one time. 4.4.2 Sampling

43、 for examination. Sample lanterns shall be selected at random in accordance with MIL-STD-105, at inspection level I, for the examination specified in 4.5. The AQL shall be 2.5 defective. Any lantern in the sample containing one or more defects shall not be offered for delivery and if the number of n

44、onconforming lanterns in any sample exceeds the acceptance number for that sample, the lot represented by the sample shall not be offered for delivery. 6 Licensed by Information Handling ServicesMIL-L- 1 130E 4.43 Sampling quality conformance tests, Sample lanterns shall be selected at random in acc

45、ordance with M&-STD-lOS at inspection level U for the tests specified in 4.6.1 through 4.6.3. If any sample fails to comply with these tests, the lantern and the lot represented thereby shall not be offered for delivery. 4.4.4 Acceptable commercial parts, For component parts, such as cable, wire, co

46、nnectors, lamps, switches, wire terminals, tape and so forth the contractor shall certify that the material affered conforms to the following as applicable: (a) UL approved (b) Conforms to ASA standards (c) Complies with specification requirements (d) Conforms to known acceptable commercial standard

47、s. 4.5 Examination, Each sample selected in accordance with 4.4.2 shall be subjected to a surface examination to ascertain that shape, material, dimensions, marking, weight and workmanship conform to the requirements of this specification. 4.6 Tests. 4.6.1 Operation, The lantern, with batteries inst

48、alled, shall be operated by actuating the switch ten times. The lamp housing shall operate smoothly throughout its arc. The tightening device shall assure positive locking in any desired position. 4.6.2 Dielectric strength. Each sample selected shall be subjected, for 1 minute, to a di- electric tes

49、t voltage, the effective potential of which is loo0 volts, applied between points of polarity and also between live parts and ground. The frequency of the test voltage shall be 60 Hertz root mean square, alternating current and shali approximate a true sine wave. 4.63 Insulation resistance. Insulation resistance shall be measured between all current- carrying parts and non-current-carrying parts with a megometer at a voltage not less than 500 volts direct current at normal room temperature. This test shall follow the dielectric test. 4.6.4 Salt spray, Salt spray test shall be conducte