NAVY MIL-L-24282-1968 LIGHT SIGNAL MULTIPURPOSE KIT NONMAGNETIC SYMBOL 106 1《符号106 1的多用途非磁性光信号装置》.pdf

1、MIL-L-24282 58 777770b 0152982 b W 3 July 1968 SUPERSEDING MS 19106 (SHIPS) 16 November 1961 MILITARY SPECIFICATION LIGHT, SIGNAL, MULTIPURPOSE, KIT, NONMAGNETIC, SYMBOL 106.1 1. SCOPE 1.1 This specification covers a nonmagnetic, portable, multipurpose light, Symbol 106.1, complete with red, green,

2、and yellow lenses and a stowage box for signaling, visual communications, and limited lighting for shipboard use. It can be operated by 115-volt, alternating current (a. c. ) or by self-contained dry cell batteries. 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date

3、of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL TT- C-490 TT-P-664 - Cleaning Methods and Pretratment of Ferrous Surfaces for OrganicCoatings. - Primer Coating, Synthetic, Rust Inhibiting, Lacquer-Resisting. MIL

4、ITARY MIL-R-11 MIL-M-14 MIL-B-18/1 MIL-R-900 MIL-S-901 MIL-E-917 MIL-D-1000/2 MIL-R-2726/50 MIL-T-7928 MIL-P-8585 MIL-M-10578 MIL- P- 15024 MIL- P- 15037 MIL-E-15090 MIL- P- 15328 MIL-1-17214 MIL-E-17555 MIL-S-19622 MIL-L-19896 MIL-1-45208 STANDARDS - Resistors, Fixed, Composition (Insulated) Genera

5、l Specification. - Molding Plastics and Molded Plastic Parts, Thermosetting. - Batteries, Dry, BA-2. - Rubber Gasket Material, 45 Durometer Hardness For Moderately Low Tem- perature Service. - Shock Tests, H. I. (High Impact); Shipboard Machinery, Equipment, and Systems, Requirements for - Electric

6、Power Equipment, Basic Requirements for (Naval Shipboard). - Drawings, Engineering and Associated Lists. - Receptacle, Plug, Electrical, 15 Ampere, 125/250 Volts, 2 Pole Grounded - Terminals, Lug Splices, Conductor: Crimp Style, Copper. - Primer Coating, Zinc Chromate, Low-Moisture-Sensitivity. - Me

7、tal Conditioner and Rust Remover (Phosphorus Acid Base). - Plates, Identification-Information and Marking for Identification of Electri- - Plastic Sheet, Laminated, Thermosetting, Glass Cloth, Melamine Resin. - Enamel, Equipment, Light Gray (Formula No. 111). - Primer, Pretreatment (Formula No. 117

8、For Metals). - Indicator, Permeability; Low-Mu (Go-No-Go). - Electronic and Electrical Equipment and Associated Repair Parts, Pre- - Stuffing Tubes (Nylon), General Specification. - Labels and Label Tape, Pressure Sensitive Adhesive, Paper, Water Resist- - Inspection System Requirements. (Symbol No.

9、 720.3). cal, Electronic and Mechanical Equipment, paration for Delivery of. ant. MILITARY MIL-STD-167 MIL-STD-202 MS3102 - Connector, Receptacle, Electric, Box Mounting. - Mechanical Vibrations of Shipboard Equipment. - Test.Methods for Electronic and Electrical Component Parts. THIS DOWMENT clsNTA

10、iNis 15 PAGES, K FSC 5850 * r . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ . MIL-L-p4ZF5- W 79F9b -0152?83p B fi MIL-L-24282(SHIPS) - Connector, Plug, Electric, Straight. - Lampholder for Two-Prong Sealed Beam Lamp. - Lamp, Incandescent, PAR

11、46, Mogul End Prong, Stippled Cover, Multi- purpose Signal. - Switches, Toggle, Double Pole, One-Hole Mounting (Sealed Toggle Bushing) (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the

12、procuring activity or as directed by the con- tracting officer, ) 2.2 Other publications. The following documents form a part of this specification to the extent specifie herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal MS 16569 - Switch,

13、 Toggle, D, P. S. T. MB 16655 MS 16845 M8 25100 NATIONAL FIRE PROTECTION ASSOCTATION(NFPA) 70 - National Electrical Code. (Application for copies should be addressed to National Fire Protection Association, 60 Batterymarch NATIONAL BUREAU OF STANDARDS Street, Boston, Massachusetts 02110. ) Handbook

14、H28 - Screw Thread Standards for Federal Services. Handbook 95 - Standard Colors of Signal Lights. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D. C. 20402. ) UNIFORM CLASSIFICATION COMMITTEE Uniform Freight Classification Ru

15、les. (Application for copies should be addressed to the Uniform Classification Committee, 202 Union Station, AMERICAN WELDING SOCIETY 516 West Jackson Blvd, Chicago, lilinois 60606.) Welding Handbook (Application for copies should be addressed to the American Welding Society, Inc., United Engineerin

16、g (Technical sociey and technical association specifications and standards are generally available for Center, 345 East 47th Street, New York, N. Y. 10017. ) reference from libraries. They are also distributed among technical groups and using Federal agencies. ) 3, REQUIREMENTS 3.1 Sample for first

17、article inspection. Prior to production, a sample manufactured by productiontools and processes shall be tested as specified in 4.2 (see 6.3). 3.2 -, The signai light kit shall be designed to conform to figures 1 through 4 and as specified 3.3 Construction. The signal light shall be constructed for

18、long service without frequent overhaul herein, The light shall be suitable for signaling, visual communications, and limited lighting. under severe conditions encountered aboard ship. The construction shall be simple and sturdy and such that continued satisfactory operation in accordance with this s

19、pecification and routine maintenance in service do not require special tools or excessively precise workmanchip. Special tools are defined as those tools not listed in the Federai Supply Catalog. (Copies of this Catalog may be consulted in the Officer of the De- fense Crontract Administrative Servic

20、e (DCAS). 3.4 Materidei, Materials shall be as specified herein, and shall meet the performance requirements specified heroin, Ail materials shall be noncorrosive and nonmagnetic. 2 -_ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.1 Nonmagnetic.

21、The magnetic permeability of all fixture parts shall be 2. O, or less, after fabrica- tion. The transformer is excluded. 3.4.2 Plastics. Plastic materials shall be free o defects such as embedded particles, bubbles, scratches. blemishes, and striations. 3.4.3.1 Metals. All metals used in fabrication

22、 and assembly shall be treated to prevent distortion or failure due to stresses or other conditions resulting from working, forming, and welding. Heating or peening after welding will accomplish stress relief (see American Welding Society Welding Handbook). 3.4.3.2 Plastics. Adequate measures shall

23、be taken in molding and processing plastics to insure that stress buildup does not occur, or is satisfactorily treated to relieve these stresses to prevent deterioration or failure of the part or assembly. 3.4.5 Rubber. Material for rubber gaskets shall conform to MIL-R-900, 3.4.6 Dissimilar metals.

24、 Application and use of dissimilar metals shdl conform to the requirements I 3.4.7.1 Cast iron (gray iron) or other brittle material shall not be used. 3.4.7.2 Material listed in MIL-E-917 as prohibited shall not be used. 3.5 Threaded parts. Screw breads shall be UNC class 2 of Handbook H 28. I 3.5.

25、1 Inserts, tapping, and threaded devices. Inserts, tapping, and threaded devices shall be as fol- (a) Self-tapping screws and sheet metal screws shall not be used. (b) Molded-in-place inserts in plastic for screw threads are required. 3.6 Welding. Welding and allied processes used in fabrication sha

26、ll be in accordance with the American 3.7 Bearg spread. The signal light shall be so designed to permit the following beam spread limits: Welding Society Welding Handbook. Horizontal - 7 degrees Vertical - 7 degrees 3.8 Castings. Castings shall be free from cold shuts, blow holes, or any imperfectio

27、ns that may affect 3.9 Dimensional tolerances. The following tolerances shall apply: strength. They shall be finished smooth, that is, no openings or rough edges. (a) Fractional f 1/64 inch. (b) Decimal parts identification by style, model, or catalog number as available; and com- plete wiring diagr

28、am. 3.12.8 Batteries. Batteries shall be type BA-2,22 1/2 volt in accordance with MIL-B-18/1. Three batteries shall be connected in parallel. Unless otherwise specified (see 6. 2), batteries need not be fur- nished by the contractor. 3.12.9 Stowage box. Stowage box in general shall be constructed as

29、 shown on figure 4. Overall size shall be kept to a minimum. The dimensions shall not exceed those shown on figure 4. Material shall be a 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3,12.9.3 Lamp receptacle. The receptacle for energizing the la

30、mp shall be MS 3102 R-1OSL-3P at- tached. to the box adjacent to the transformer. A plastic cap attached to a safety wire anchored to the box shail be provided over the receptacle for protection. 3.12.9.4 Power supply receptacle. The power supply receptacle shall be industry number 5278, male, and s

31、hall be flush-mounted to the box adjacent to the transformer. 313 Weight. Component parts shall be as small and light as possible but sufficiently rugged to with- stan rough handfng so that mechanical damage or distortion will not be of sufficient magnitude as to impair continued operation. The tota

32、l weight of the signal light shall not exceed 4-1/4 pounds without batteries . The total weight of the signal light kit, without batteries, shall not exceed 16-1/2 pounds. 3.14 Identification and switch plates. Identification and switch plates shall be in accordance with MIL- P-15024. ps shown on fi

33、gure 4, and shall be securely attached on the stowage box a8 shown on figure 4. Switch plates shall be as shown on figure 2 and shall be securely attached on the signal light as shown on figures 1 and 2. 3.15 One label, type N conforming to MIL-L-19896 shall be applied as shown on figure 1. It shall

34、 indicate the following information: “USE LAMP FSN 9G, 6240-828-3039. 3.16 Drawings. Drawings shall be type II form 2 category F of MIL-D-1000/2. In addition, reference to ME-L-24282 shall appear in the title block or as near as possible to the title block. Drawings used for nianufacturing shall be

35、processed as specified in MIL-D-1000/2. 3, Iff. 1 Drawing distribution. The manufacturer, upon being notified that his first article inspection sample has passed the specified inspection, shall place on record a set of prints of the drawings used for manufacturing the signal light kit with the follo

36、wing activities: (a) One cet for file with the DCAS. (b) On set for file with the Naval Ship Engineering Center Department of the Navy, Wachitighn, (e) One set for file with the contracting officer. B.C. 20360. 3.17 Protection against corrosion. in order to prevent corrosion, all metal parts shall b

37、e of corro- sien-resisting materials orother materials treated in a manner to render them adequately resistant to cor- rosion, Treatment shall be in accordance with MZ-E-917. MIL-L-24282(SHIPS) good commercial grade Of aluminum, protected against corrosion and of sufficient gage to provide firm sup-

38、 port for component and compartmentation -.ithout excessive weight. A commercially available boxand cover, adapted for the purpose, of drawn or fabricated construction will be acceptable. 3.12, O, 1 Compartmentation. Compartmentation shall be provided for items specified in 3.12.1 alu- minum baffles

39、 and CUShiOnS of foamed plastic, rubber, or felt shall be provided to prevent movement and damage of components in transit and stowage aboard ship. Kits shall conform to the requirements of 3.11.4 and 3.11+5. 3.12.9.2 Transformer. The transformer shall be 115/20 volt. The transformer shall be firmly

40、 mount- ed to the box and wired to receptacles as shown on the wiring diagram, figure 3. 3,lO.l Cleaning, After all machining, welding, and brazing operations are completed, the exterior ;uid interior surfacesof all metal enclosures shall have all rust or other visible corrosion products remove (rus

41、t removal from ferrous metal surfaces shall be in accordance with MIL-M-10578, and shall be thoroughl cleaned of all grease, oil, and dirt by solvent wiping, vapor degreasing, or caustic washing and rinsing. 6 3.18 Painting. AI1 aluminum parts shall be completely painted in accordance with the requi

42、rements specified hereinafter. Plastic enclosures normally will not be painted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-24282(SHIPS) 3.18.2 Undercoats. Either of the following undercoats shall be applied: (a) One coat of primer pretreat

43、ment coating in accordance with MIL-P-15328 shall be applied as a continuous film O. 0002 to O. 0005 inch thick. (b) A hot diptank phosphate or chromate-phosphate treatment conforming to type I of TT-C-490 fol- lowed by one coat of primer, conforming to TT-P-664 or MIL-P-8585 and applied as a contin

44、- uous film O. 0002 to O. O01 inch thick. 3.18.3 Finish coats. Light gray enamel conforming to MIL-E-15090 shall be applied in sufficient thick- ness over the undercoat to provide protection of the equipment and to provide a satisfactory appearance. 3.19 Workmanship. The signaling light shall be man

45、ufactured and finished in a first class manner. Particular attention shall be paid to neatness and thoroughness of soldering, wiring, marking of parts and assemblies, machine screw assemblage, welding, freedom of parts from burrs and rough edges, and finish, 4. QUALITY ASSURANCE PROVISIONS 4.1 Respo

46、nsibility for inspection. Unless .otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities su

47、itable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to

48、prescribed requirements. 4.1.1 Inspection system. with MIL-1-45208. The supplier shall provide and maintain an inspection system in accordance 4.2 First article inspection. The first article inspection sample (s) shall be subjected to the examina- tion specified in 4.3.3 and the tests of 4.4, 4.3 Qu

49、ality conformance inspection. 4.3.1 Lot. For the purpose of sampling, a lot shall be the identical number of signal light kits on the contract or order. 4. 3.2 Sampling for examination and tests. A random sample of signaling light kits shall be selected in accordance with table I from each lot for the examination of 4.3.3 and the tests specified in 4.3.4. Any signal light kit containing one or more defects or failing one or more tests shall not be offered for delivery. If the number of su