1、MIL-L-5602 13 M 9797706 0365422 3 M e- ! x-37*/4 MIL-L-85602 (AS) i3 October i983 MILITARY SPECIFICATION LEAD , EXPLOSIVE MARK 28 MOD O MARK 29 MOD O This specification”is approved for use by the Naval Air Systems Com- mand, Department of the Navy, and is available for use by all Depart- ments and A
2、gencies of the Department of Defense. 1. SCOPE. 1.1 Scope. This specification establishes the requirements for manu- facture and acceptance of two types of explosive leads, as classified in 1.2 and described in 3.1. 1.2 Classification. Leads covered by this specification are of the Type I Lead, Expl
3、osive, MARK 28 MOD O Drawing 1137AS2161. Type II Lead, Explosive, MARK 29 MOD O Drawing 1137AS2164. following types : 2. APPLICABLE DOCUMENTS. 2.1 Government documents. 2.1.1 Specifications and standards. Unless otherwise specified , the following specifications and standards of the issue listed in
4、that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. I Beneficial comments (recommendations, additions , deletions) and any pertinent data which may be of use in improvin
5、g this document should be addressed to: Commanding Officer , Naval Air Engineer- ing Center , Engineering Specifications and Standards Department (ESSD) , Code 93 , Lakehurst , N J 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of
6、 this document, or by letter. L lTE5G-f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-L-5602 13 m 9999906 0365423 5 m MIL-L-85602(AS) SPECIFICATIONS MILITARY MIL -A- 25 50 Ammunition, General Specification for. MIL-H-6875 MIL-T-18303 Heat Tre
7、atment of Steels (Aerospace Practice, Process for). Test Procedures ; Preproduction , Acceptance, and Life for Aircraft Electronic Equipment , Format for. MIL-C-21723 Composition CH-6. STANDARDS FEDERAL FED-STD-102 Preservation , Packaging , and Packing Levels. MILITARY MIL-STD-129 Marking for Shipm
8、ent and Storage. MIL-STD-331 MIL-STD-414 Fuze and Fuze Components Environ- mental and Performance Tests for. Sampling Procedures and Tables for Inspection by Variables for Percent Defective. MIL- STD-453 Inspection Radiographic. MIL-STD-810 Environmental Test Methods. MIL-STD-1695 Environments, Work
9、ing , Minimum Standards for, MIL-STD-45662 Calibration Systems Requlrements . (Copies of specifications and standards required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) Government do
10、cuments and drawings of the issue specified in the solici- tation form a part of this specification to the extent specified herein. 2.1.2 Other Government documents and drawings. The following other 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-f
11、lIL-L-5b02 13 m 7779706 03b5424 7 m MIL-L-85602 (AS) OTHER GOVERNMENT DOCUMENTS CODE OF FEDERAL, REGULATIONS (CFR) 49 CFR 171-178 Transportation. DEPARTMENT OF DEFENSE (DoD) DoD 4145.26M DoD Contractors Safety Manual for Ammunition, Explosives and Related Dangerous Material. (Application for copies
12、should be addressed to the Superintendent of Documents, Government Printing Office , Washington, D. C. 20402, ) DRAWINGS NAVAL AIR SYSTEMS COMMAND (Code Ident 30003) 1137AS2161 Lead, Explosive, MARK 28 MOD O. 1137A 52164 Lead, Explosive, MARK 29 MOD O. SA1137AS2167 Fixture , Vibration Test. SA1137AS
13、2168 Fixture , Jolt Test. SA1137AS2169 Fixture , 12-Meter Drop Test. 1137AS2171 Container , Shipping and Storage (for 500 MARK 28 MOD O Explosive Leads) Packing and Marking. 1137AS2172 Container, Shipping and Storage (for 100 MARK 29 MOD 0 Explosive Leads) Packing and Marking. (Copies of drawings re
14、quired by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-85602 (AS) 2.2 Other public
15、ations. The following documents form a part of this specification to the extent specified herein. which are indicated as DoD adopted shall be the issue listed in the cur- rent DoDISS and the supplement thereto, if applicable. The issues of the documents AMERICAN SOCIETY FOR TESTING AND MATERIALS (AS
16、TM) ASTM A-108 ASTM A-582 Steel Bars , Carbon , Cold-finished, Standard Quality , Specification for. Free-machining Stainless and Heat- resisting Steel Bars , Hot-rolled or Cold-finished , Specification for. (Application for copies of ASTM publications should be addressed to the American Society for
17、 Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. ) In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. 2.3 Order of precedence. 3. REQUIREMENTS. 3.1 to detonate a Type I lead in a sa
18、fety-arming (S-A) device. 3.1.1 Government-furnished property. Unless otherwise specified in the contract or purchase order, the Government will furnish the con- tractor with the following components in a sufficient quantity to perform the function and output test specified herein (see 4.6.2 and 6.2
19、.3): a. MARK 9 MOD O Explosive Leads in accordance with LD 480141. Item description. The Type II lead performs a transfer function b , Exploding bridgewire (EBW) detonators in accordance with 4.6.2.1.2.a. 3.2 Characteristics. Unless otherwise specified herein , the following requirements apply for b
20、oth the Type I lead and the Type II lead. 3.2.1 Explosive charge moisture content. The explosive charge in the lead shall be Composition CH-6 in accordance with MIL-(2-21723. moisture content of the explosive charge shall not exceed 0.20 percent at the time of loading (see 4.6-1). The 4 Provided by
21、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-5602 13 7999906 03b542b O 3.2.2 Performance. 3.2.2.1 Function and output. The lead shall function on the first The explosive and only try when initiated in accordance with 4.6,2. output shall meet the accepta
22、nce criteria specified in 4.2.2 for the first article and in 4.3.1.3 for the, inspection lot, 3.2.2.2 Environmental. The lead shall not be damaged nor shall safety or subsequent performance be degraded by exposure to the following environments. 3.2 2.2.1 Transportation vibration-temperature . The le
23、ad shall meet the requirements of 3.2.2.1 after exposure to the environment of 4.6.3.1. 3.2.2.2.2 Temperature and humidity. The lead shall meet the require- 3.2.2.2.3 Flight vibration. The lead shall meet the requirements of ments of 3.2.2.1 after exposure to the environment of 4.6.3.2. 3.2.2.1 afte
24、r exposure to the environment of 4.6.3.3. 3.2.2.3 Safety. 3.2.2.3.1 Jolt. The lead shall be safe to handle and dispose of after exposure to LKenvironment of 4.6.4.1. 3.2.2.3.2 Twelve-meter drop. 3.2.3 Radiographic. The lead shall be safe to handle and dispose of after exposure to the environment of
25、4.6.4.2. cracks, voids , fissures , or loose powder when radiographically inspected (see 4.6.5). cracks, dents, pits, burrs , or other blemishes , when visually inspected (see 4.6.6). When specified in the contract or purchase order, a sample of Type I or Type II leads shall be subjected to first ar
26、ticle inspections (see 4.2 and 6.2.4). The lead shall be free from defects such as 3.2.4 Visual. There shall be no evidence of external damage, such as 3.3 First article. 3.4 Design and construction. 3.4.1 Production drawings. The lead shall meet all the requirements of and shall be manufactured and
27、 assembled in accordance with Draw- ing 1137AS2161 and all associated documents for Type I and on Draw- ing 1137AS2164 and all associated documents for Type II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-L-5602 13 H 9977906 0365427 2 3.4.2 S
28、afety precautions. As a minimum, the safety precautions of DoD 4145.26M shall apply during manufacture, handling , and inspection of the leads, but shall not be considered as a substitution for the con- tractors own safety procedures developed to accommodate the hazards associated with the lead. 3.4
29、.3 Standards of manufacture. 3.4.3.1 Product cleanliness. No oils or solid lubricants of any kind shall be used on any part of the lead after final cleaning o components, except as specified on the drawings, 3.4.3.2 Workin environment. The working environment shall meet the minimum +- evels and requ
30、irements of MIL-STD-1695. 3.4.3.3 Workmanship, Workmanship shall meet the requirements of MIL-A-2550. 4. QUALITY ASSURANCE PROVISIONS. 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the perform- ance of all inspectio
31、n requirements as specified herein (see 6.2.1). Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the per- formance of the inspection requirements specified herein , unless dis- approved by the Government (see 6.2.1).
32、 right to perform or witness any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. herein are classified as follows: The Government reserves the 4.1.1 Classification of inspections. Inspe
33、ction requirements specified a. First article inspections (see 4.2). b . Quality conformance inspections (see 4.3). 4.2 First article inspections. When specified in the contract or pur- chase order, first article inspections shall be performed by the contractor after award of contract and prior to p
34、roduction (see 6.2.4). As speci- fied in the contract or purchase order, first article inspections shall be performed on 50 Type I or 50 Type I.leads which have been produced with the equipment, material, and procedures to be used in production (see 6.2.4). First article approval is valid only on th
35、e contract under which it is granted unless extended by the Government to other con- tracts. Any production prior to approval of the first article shall be at the risk of the contractor. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-5602 13
36、 W 7977706 0365428 4 MIL-L-85603( AS) 4.2.1 First article inspection sequence. The first article of 50 Type I or 50 Type II leads shall be subjected to the inspections of Figure 1 in the sequence shown. At the conclusion of the inspection sequence and after receipt of first article approval, any rem
37、ains of the first article shall be disposed of at the discretion of the cognizant demolition officer. 4.2.2 First article, acceptance and rejection criteria, Each first article lead shall meet the requirements specified in the contract or purchase arder, on the drawings, and herein. For the inspecti
38、ons of Figure 1, the applicable requirements of Section 3 shall be met on the first and only trial; one or more failures shall be cause for refusal to grant first article approval. For the function and output test of 4.6.2, acceptance or rejection of the first article shall be based on the following
39、 criteria: a. A depth of dent of less than 0.075 inch from any Type I sample lead or less than 0.038 inch from any Type II sample lead, when measured in accordance with 4.6.2.3. shall be cause for rejection of the first article. b. The first article shall be accepted if the quantity (x-L)/s, when co
40、mputed in accordance with 4.6.2.3.d, is equal to or greater than the k value of MIL-STD-414, Table B-I, Accept- able Quality Level (AQL) of 0.65 percent defective. A quantity less than the k value shall be cause for rejection of the first article. 4.3 Quality conformance inspections. 4.3.1 Inspectio
41、n lot. As specified in the contract or purchase order, an inspection lot shall consist of completed Type I or Type II leads, fabricated under the same conditions and offered for acceptance inspec- tion at the same time (see 6.2.1). 4.3.1.1 Inspection lot size. The inspection lot size shall be as spe
42、ci- fied in the contract or purchase order (see 6.2.1). 4.3.1.2 Inspection lot acceptance inspection sequence. After the inspection lot has been formed and identified by lot number, the lot shall be subjected to the inspections of Figure 2 in the sequence shown. Where specified during the inspection
43、 sequence, a quantity of leads shall be randomly sampled from the inspection lot in accordance with MIL-STD-414 , Inspection Level IV, Standard Deviation Method, Variability Unknown. As the sample continues through the inspection sequence, the remainder of the lot shall be held in bond. If the sampl
44、e does not cause lot rejection (see 4.3.1.3), the remainder of the lot shall continue through the inspection sequence as shown on Figure 2. Upon completion of the inspection sequence, the remains of the sample leads shall be disposed of at the discretion of the cognizant demolition officer. 7 Provid
45、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-85b02 13-= 7777706 03b5927 b 4.3.1.3 Inspection lot acceptance and rejection criteria. Each lead of the inspection lot shall meet all the requirements specified in the contract or purchase order, on the
46、 drawings, and herein. For the inspections of Figure 2, each sample lead shall meet the applicable requirements of Section 3 on the first and only trial. For the function and output test of 4.6.2, acceptance or rejection of the inspection lot shall be based on the following criteria: a. A depth of d
47、ent of less than 0.075 inch from any Type I sample lead or less than 0.038 inch from any Type II sample lead, when measured in accordance with 4.6.2.3. shall be cause for rejection of the inspection lot. b. The inspection lot shall be accepted if the quantity (x-L/s, when computed in accordance with
48、 4.6.2.3.d, is equal to or greater than the k value of MIL-STD-414, Table B-1, AQL of 0.65 percent defective. be cause for rejection of the inspection lot. A quantity less than the k value shall 4.4 Measuring and test equipment. 4.4.1 Calibration and maintenance. All measuring and test equipment Whe
49、n specified in the contract or purchase order, the contractor utilized by the contractor for performance of the inspections specified herein shall be calibrated and maintained in accordance with MIL-STD- 45662. shall prepare a Calibration System Description in accordance with MIL- STD-45662 (see 6.2. Z). The Calibration System Description shall be accepted by the Government prior to use. 4.4.2 Standard test equipment. The contrac
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1