NAVY MIL-M-29436-1988 MODULE ASSEMBLY PALLET TYPE STORAGE《储存货盘类模块组装》.pdf

1、- .- . ps-a5-/7? MIL-fl-29436 71 M 7997706 0240464 MIL-M-29436 (MC) 20 January 1988 MILITARY SPEC1 FICATION MODULE ASSEMBLY, PALLET TYPE, STORAGE This specification is approved for use within U.S. Marine Corps, Department of the Navy, and is available for use by all departments and agencies of the D

2、epartment of Defense. ? 1. SCOPE 1.1 Scope. This specification establishes the requirements. for / manufacture and acceptance of the Module Assembly, Pallet Type, Storage. This item is the only one of its type. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The

3、 fo1,lowing specifica- tions and standards form a part of this specification to the extent specified herein. Unless otherwise speci?fied, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards 0 . (DODISS) and supplement th

4、ereto, cited in the solicitation. SPECIFICATIONS FEDERAL V-T-295 - Thread, Nylon. QQ-A-200/8 - . . Aluminum Alloy 6061, Bar, Rod, Shapes, QQ-A-200/9 - Aluminum Alloy 6063, Bar, Rod, Shapes, Tube and Wire, Extruded. Tube and Wire,. Extruded. 1 Beneficial comments (recommendations, additions, deletion

5、s) and any pertinent data which may be of use in improving this document should be addressed to: Commandant of the Marine Corps, Head- quarters Marine Corps (Code? LMA-1) , Washington, .DC 20380 by using the self-addressed Standardization Document Improvement . Proposal (DD Form 1426) appearing at t

6、he end of this document or by letter. AMSC N/A FSC 7125 DISTRIBUTION STATEMENT A. Approved for public release; distribution 0 is unlimited. ? THIS DOCUMENT CONTAINS q PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29436 (MC) (7Q-A-22518

7、 QQ-A-25 0/8 QQ-s-701 PPP-B-60 1 PPP-B- 6 3 1 MILITARY MIL-P-116 MIL-B-117 MIL-T-70 4 MIL-W-4 O 8 8 MIL-C-55 41 MIL-Em60 60 MIL-G-12 803 MIL-P- 1983 4 MIL-(2-22750 MIL-W-45 205 MIL-P- 530 2 2 STANDARDS FEDERAL FED- ST D- 5 9 5 MILITARY MIL-STD-10 5 MIL-STD-12 9 MIL-STD-13 O Aluminum Alloy 6061, Bar,

8、 Rod, Wire nd Special Shapes, Rclled, Drawr, c.r Cold Finished. Aluminum Alloy 5052, Plate ar,d Sheet. Strapping, Steel and Seals. Boxes, Wood, Cleated Plywood. Box, Wood, Nailed and Lock-corner. Preservation, Methods of. Bag, Sleeve and Tubing - Interior Packaging. Treatment and Painting of Materia

9、l. Webbing, Textile, Woven Nylon. Chemical Conversion Coatings on Aluminum Alloys. Envelope, Packaging, Water Vapor Proof, Flexible. Gasket Material, Non-Metalic. Plate, Identification, Metal Foil, Adhesive Back. Coating, Epoxy Polyamide. Welding, Gas Metal-Arc and Gas Tungsten- Arc, Aluminum Alloys

10、, Readily Weldable for Structures, Excluding Amor. Primer, Epoxy Coating, Corrosion Inhibiting, Lead and Chromate Free. Federal Standard Colors. Sampling Procedures and Tables for Inspec- tion by Attributes. Marking for Shipment and Storage. Identification Marking of U.S. Military ProDertv MIL-STD-2

11、0 73-1A - DoD- Material Procedures for Development and Application of Packaging Requirements. 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless ot

12、herwise specified, the issues shall be those in effect on the date of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-M-29936 71 9999906 02909b6 1 ._ MIL-M-29436 (MC) DRAWINGS U.S. Marine Corps Logistics Base, Albany, GA 82A

13、5048A1900 - Module Assembly, Pallet Type, Storage 82A50 50A0100 - Rail Assembly and Installation, Mounting, 82A50 50A0110 - Peg Assembly, Modular Aligiiment 82A5050A0132 - Bar, Lock 82A50 50A0138 - Shaft, Latch 82A5050A0140 - Head, Latch 82A50 50A0142 - Handle, Latch 82A5050A0144 - Latch 82A5050A015

14、0 - Rail Assembly and Installation, Mounting, 82A50 50A0160 - Post Assembly, Mounting Floor , Wall (Copies of specificatins, standards, handbooks, drawings, publica- tions, and other government documents required by contractors in connection with specific procurement functions shoul6 be obtained fro

15、m the contracting activity or as directed by the contracting activity). 2. 2 Other publications. The following document (s) form a part of this specification to the extent specified herein. Unless other- wise. specified, the issues .of the ocknents which are DOD adopted shall be those listed in the.

16、issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of docments not listed in the DODISS shallbe the issue of the nongovernment documents which is current on the date of the solicitation. NRICAN NATIONAL STANDARDS INSTITUTE ANSI/AWS A2.4-79 - Welding and Nondest

17、ructive Testing, ANSI/AWS A3.0-85 - Welding Terms and Definitions. Symbols. (Application for copies should be addressed to the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) (Nongovernment standards and other publications are normally avail- able from the organizati

18、ons which prepare or which distribute the documents. These. documents also may be available in or through libraries or other informational services.) . . 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated

19、detail specifications, specification sheets or MS standards), the text of this specification shall take pre- cedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3 /- -. Provided by IHSNot for ResaleNo reprodu

20、ction or networking permitted without license from IHS-,-,-MIL-M-29436 (MC) 3, REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3 and 6.4). 3.2 Materials. The materials and components shall be certifie2 t

21、o conform to the applicable specification and standards as liste6 on the drawing package 82A5048A1900 or required herein. The materials used may include reclaimed materials provided such materials will not jeopardize its intended use and performance. The reclaimed materials shall have been reprocess

22、ed, remanufactured, or recycled in a manner which will restore them to the same chemical composition and physical properties as the materials oricinally selected for use as specified herein. 3.3 Design. Module Assembly, Pallet Type, Storage, shall be of the design specified on drawing package 82A504

23、8A1900 (see 2.1.2). 3.4 Construction. Module Assembly, Pallet Type, Storage, shall be of the construction and physical dimensions specified on drawing package 82A5048A1900 (see 2.1.2). 3.4.1 Frame assembly. The frame assembly shall be fabricated rom Rod; Aluminum .Alloy, 6061-T6, QQ-A-225/8; Aluminu

24、m Alloy 6063-T6, QQ-A-200/9; Angle, Aluminum Alloy, 6061-T6, QQ-A-200/8; and shall be square in all directions within .O10 inch per foot (see 0.4.2). All welds shall be in accordance with ANSI/AWS A3.0-85, A2.4-79 ancl MIL-W-45205, Class B (see 4.4.4). The frame assembly shall conform to specificati

25、ons to such a degree of accuracy ensuring it wiJ.1 align to the peg and pin assemblies and lock using the swing latches as illustrated in the .footprint drawing, Figure 1 (see 4.4.3). 3.4.2 Pallet assembly. The pallet assembly shall be fabricated from Sheet, Aluminum Alloy 5052-H32, .19 inch thick,

26、QQ-A-250/8. The assembly shall be mounted to the frame using 6 ring and stud assemblies and 2 bolts (see 4.4.5). 34.3 Strap assembly, tie down. The strap assembly, tie down shall be fabricated from Strap, Webbing, MIL-W-4088, Type II, Class I, 2500 lbs minimum strength, color Gray; Strap, Webbing MI

27、L-W-4088, Type XXVII, Class I, 6500 lbs minimum strength, color Gray; sewn with Thread per Fed Spec V-T-295, Typ-e II, Class A, Type B, color Black per FED-STD-595. Attaching hardware will consist of Rotating End Fitting; Plate, Threading; Hook, Flat; and Fastener, Flat Hook. Attaching hardware shal

28、l be Cold Rolled Steel, 300 lbs minimum strength with HD Zinc Plate Bronze Chromate Finish. The strap assembly shall be fabricated to have a minimum strength of 300 lbs (see 4.4.6). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-U-29436 71 .97

29、79906 0240468 5 MIL-M-29436 (MC) 3.4.4 Strap assembly. The strap assembly shall be made frcm Strap, Webbing Type XXVII, Clilss 1 and Strap, Webbing Type II, Class 1. The webbing color shall be Forest Green and all ends shall be fused to provide a smooth edge with the cut ends all fused together (see

30、 4.4.7) . 3.4.5 Bracket mounting. The bracket, mounting, shall be fabricated of Angle, Aluminum Alloy, 6061-T6, QQ-A-200/8 and shall be bolted to the frame in 4 piaces (see 4.4.7). The bracket, mounting, shall be bolted to the frame to such a degree of accuracy ensuring it will align to the footprin

31、t as described in Figure 1 (see 4.4.8). 3.4.6 Decal. The decal shall be fabricated from .O03 inch thick aluminum alloy foil, photographically sensitized, adhesive back in accordance with MIL-P-19834, Type I. Requirements and methods of marking the decal shall be in accordance with MIL- STD-130. Unle

32、ss otherwise specified all characters shall be .O93 inch high on finished decal, color shall be in accordance with MIL-P-19834, Style III (see 4.4.9). It shall be attached to the frame center horizontal member 5 inches,from the left edge. 3.5 Finish. . 3.5.1 Cleaninq. Prior to painting metal surface

33、s shall be cleaned and treated per MIL-T-704, Type G, and MIL-C-5541, Class 3. 3.5.2 Priminq. After metal surfaces have been cleaned as required they shall be primed per MIL-P-53022, with a minimum dry film thickness of .O01 inch in one coat. 3.5.3 Paintin%. Final finish painting shall have a minimu

34、m . dry coat film thickness of .O018 inch in two coats.per MIL-C-22750, . Type II., Color No. 24533 per FED-STD-595 (see 4.4.12). 3.6 Interchangeability. All parts having the same part number shall be functionally and dimensionally interchangeable. Inter- changeable parts are. defined as two or more

35、 like parts possessing such functional and physical char.acteristics as to be equivalent in performance and durability, and capable of being exchanged one for the other without alteration of the parts themselves or adjoining parts and without selection for. fit or performance. 3.7 Workmanship. The M

36、odule. Assembly, Pallet Type, Storage shall meet all design, fabrication, assembly and finish require- ments of this specification. Particular attention shall be given to; removal of burrs and sharp edges; accuracy of dimensions; thoroughness of welding; painting; alignment; tightness of screws; bol

37、ts, and rivets. Failure to ensure these measures have been taken will be considered adequate basis for rejection of items being of inferior quality for the purpose intended. . 5 - r Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29436 (MC) 4 .

38、 QUALITY ASSURANCE PROVIS IONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible fer the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the c

39、ontractor may use his own or any-other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by. the Government. The Government reserves the right to perform any of the inspections set forth in the specifica- tion where such inspections are deeme

40、d necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of section 3 and 5. The inspection set forth in this specification shall become a part of the contractozs overall inspection system or quality pro

41、gram. The absence of any inspec- tion requirements in the specification shall not relieve the contrac- tor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply sith all require- ments of the contract. Sampling in quality conformance does n

42、ot authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. (see 6.2) the contractor shall insure that test and inspection facilities of sufficient accuracy, quality and quantity are established and maintaine

43、d to permit performance of required inspections. 4.1.2 Test equipment and inspection facilities. When specifiec! 4.2 Classification of inspections. The inspections specizied herein are classified as follows: a. First article inspection. First article inspection consists of examinations and tests per

44、formed on samples which are representative of the production item after award of a contract to determine that the production item conforms to the requirements of this specification (see 4.3) . b. Quality conformance inspection. Quality conformance inspection consists of examinations and tests perfor

45、med on in- dividual products to determine conformance of the products with the requirements set forth in this specification (see 4.4). C. Visual inspection. Visuai inspectin consists of examinations to determine conformance with the requirements se.t forth in this specification (see 4.5). 4.3 First

46、article inspection. The first article inspection OE the Module Assembly, Pallet Type Storage shall consist of examination and tests for al1 the requirements of this cpecifi- cati on. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-27LI36 71 7

47、777706 0240q70 3 m MIL-M-29436 (MC) 4.3.1 First article sample. Unless otherwise specified as soon as practical after the award of the contract, the contractor shall submit quantity (s) specified in the contract for Module Assembly, Pallet Type, Storage. The modules shall be representative of the co

48、nstruction, workmanship., components, and materials to be used during production. Approval of the first article inspection . samples or the waiving of the first article inspection does not preclude the requirements for performing the quality conformance inspection. The first article inspection sampl

49、es shall be furnished to the Government as directed by the Contracting Officer (see 6.2). 4.3.2 Sample disposition. Upon completion of the first article inspection, sample(s) will be disposed of in accordance with Govern- ment shipping instructions. shall consist of those items listed in Table I. 4.3.3 First article inspection routine. First article inspection 4.4 Quality conformance inspection. Quality conformance inspections shall be conducted i