NAVY MIL-M-29442-1988 MODULE ASSEMBLY PERSONNEL STORAGE《人员储存模块组装》.pdf

1、MIL-M-27442 72 W 777970b 0240558 b c- c MIL-M-29 44 2 (MC ) 20 January 1988 MILITARY SPECIFICATION MODULE ASSEMBLY, PERSONNEL STORAGE This specification is approved for use within U.S. Marine Corps, Department of the Navy, and is available for use by all departments and agencies of the Department of

2、 Defense. 1. SCOPE 1.1 Scope. This specification establishes the requirements for manufacture and acceptance of the Module Assembly, Personnel Storage. This item is the only one of its type. 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications and standards. The following specifi

3、- cations and standards form a part of this specification to the ,extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the . Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the s

4、olicitati.on. 0 SPECIFICATIONS FEDERAL V-T- 29 5 - Thread, Nylon. QQ-A-200/8 - Aluminum Alloy 6061, Bar, Rod, Shapes, QQ-A- 2 O0 / 9 - Aluminum Alloy 6063, Bar,-Rod, Shapes, Tube and Wire, Extruded. Tube and Wire, Extruded. Beneficial comments (recommendations, additions, deletions) and any pertinen

5、t data which may be of use in improving this document should be addressed to: Commandant of the Marine Corps, Headquarters Marine Corps (Code LMA-l), Washington, DC 20380 by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document o

6、r by.letter. AMSC N/A . .ESC 7125 _- DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. a THIS DOCUMENT CONTAINS 15 PAGES. .I .c. . . . . _. . _._ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29442 71 W 99999

7、0b 0240559 MX MIL-M-29442 (MC) QQ-A-22 5/8 QQ-A-250/8 QQ-S-70 1 PPP-B-601 PPP-B-62 1 fTARY MIL-P-116 MIL-B-117 MIL-T-704 MIL-W-40 88 MIL-(2-5541 MIL-E- 60 6 O MIL-G-12803 MI L-P-15 O 2 4 MI L-P-19 8 3 4 MIL-P-20689 MIL-C- 22 7 5 O MIL-C-24066/2 - MIL-W-45205 - MIL-P-53022 - STANDARDS FEDERAL FED-STD

8、-595 - MILITARY MIL-STD- 10 5 - MIL-STD-12 9 - MIL-STD-130 - a MIL-STD-2073-IA - Aluminum Alloy 6061, Bar, Rod, Wire and Special Shapes, Rolled, Drawn or Cold Finished. Aluminum Alloy 5052, Plate and Sheet. Strapping, Steel and Seals. Boxes, Wood, Cleated Plywood. Box, Wood, Nailed and Lock-corner.

9、Preservation, Methods of. Bag, Sleeve and Tubing - Interior Packaging. Treatment and Painting of Material. Webbing, Textile, Woven Kylon. Chemical Conversion Coatings on Aluminum Alloys. Envelope, Packaging, Water Vapor Proof, Flexible. Gasket Material, Non-Metlic. Plate, Tags and Bands for Identifi

10、- cation of Equipment. Plate, Identification, Metal Foil, Adhesive Back. Plastic, Plastisol (for Coating Metallic Objects), Coating, Epoxy Polyamide. Clip, Solid, Spring Tension. Welding, Gas Metal-Arc and Gas Tungsten- Arc, Aluminum Alloys, Readily Weldable for Structures, Excluding Armor. Primer,

11、Epoxy Coating, Corrosion Inhibiting, Lead and Chromate Free. Federal Standard Colors. Sampling Procedures and Tables for Inspection by Attributes. Marking for Shipment and Storage. Identification Marking of U.S. Military Property. DoD Material Procedures for Develop- - ment and Application of Packag

12、ing Requirements. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1- - . . _ MIL-M-27q42 71 W 7797906 0240560 MIL-M-29 44 2 (MC) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and p

13、ublications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAP71 NG S U.S. Marine Corps Logistics Base, Albany, GA 82A5048A1500 - Module Assembly, Personnel Storage 82A5050A0100 - Rai

14、l Assembly and Installation, Mounting, 82A5050A0110 - Peg Assembly, Modular Alignment 82A5050A0132 - Bar, Lock 82A5050A0138 - Shaft, Latch 82A5050A0140 - Head, Latch 82A50 50A0142 - Handle, Latch 82A5050A0144 - Latch - 82A50 50A0150 - Rail Assembly and Installation, Mounting, 82A50 50A0160 - Post As

15、sembly, Mounting Floor Wal 1 (Copies of specifications, standards, handbooks, drawings, publica- tions, and other government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity

16、). 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless other- wise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise spec

17、ified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. AmRICAN NATIONAL STANDARDS INSTITUTE ANSI/AWS A2.4-79 - We1din.g and Nondestructive Testing, ANSI/AWS A3.0-85 - Welding Terms and Definitions. s

18、ymbo Is. (Application for copies should be addressed to-the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) (Nongovernment standards and other publications are norma1l.y available *from the organizations which prepare or which distri- bute the documents. These docume

19、nts also may be available in or through libraries or other informational services. ) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29 44 2 (MC) 2.3 Order of precedence. In the event of a conflict between the text of this specification and t

20、he references cited herein (except for the associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtai

21、ned. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3 and 6.4). 3.2 Materials. The materials and components shall be certified to conform to the applicable specification and standards as listed on dr

22、awing package 82A5048A1500 or required herein. The materials used may include reclaimed materials provided such materials will not jeopardize its intended use and performance. The reclaimed materials shall have been reprocessed, remanufactured, or recycled in a manner which will restore them to the

23、same chemical composition and physical properties as the materials originally selected for use as specified herein. 3.3 Desiqn. Module Assembly, Personnel Storage, shall be of the design specified on drawing package 82A5048A1500 (see 2.1.2). 3 . 4 Construction. Module Assembly, Personnel Storage, sh

24、all be of the construction and physical dimensions specified on drawing package 82A5048A1500 (see 2.1.2). 3.4.1 Frame assembly. The frame assembly shall be fabricated from Aluminum Alloy 6061, Bar, Rod, Shapes, Tube and Wire, Ex- truded, QQ-A-200/8; Aluminum Alloy 6063, Bar, Rod, Shapes, Tube and Wi

25、re, Extruded, QQ-A-200/9; Aluminum Alloy 6061, Bar, Rod, Wire and Special Shapes, Rolled, Drawn or Cold Finished, aQ-A-225/8; and shall be square in all directions within ,010 inch per foot (see 4.4.2). All welds shall be in accordance with ANSI/AWS A3.0-85, A2.4-79 and MIL-W-45205, Class B (see 4.4

26、.4). The frame assembly shall conform to specifications to such a degree of accuracy ensuring it will align to the peg and pin assemblies and lock using the swing latches as illustrated in the footprint drawing, Figure 1 (see 4.4.3). 3.4.2 Shelf cabinet. The shelf shzll be fabricated from . Sheet Al

27、uminum Alloy, 5052-H32, .O63 inch thick, QQ-A-250/8, all bend radii shall be ,060 inch minimum (see 4.4.5). The shelf shall be riveted to the sides and back panels in 13 places. .- 4 . . .- . . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I .- _.

28、MIL-U-27442 71 9 7777906 0240562 W MIL-Mi29 44 2 (MC) 3.4.3 Coat rack. The coat rack shall be fabriccrted from Sheet Aluminum Alloy, 5052-H32, .125 inch thick, QQ-A-25 0/8, the bend radii shall be .190 inch (see 4.4.5). The 14 slots for hangers shall measure 0.38 inch x 1.00 inch. The coat rack shal

29、l be riveted to the shelf in six places. . 3.4.4 Side panel. The two side panels shall be fabricated from Sheet Aluminum Alloy, 5052-H32, .O63 inch thick, QQ-A-250/8 and each side panel bolted to the frame in 8 -places. 3.4.5 Back panel. The back panel shall be fabricated from ,Sheet Aluminum Alloy,

30、 5052-H32, .O63 inch thick, QQ-A-250/8 and riveted in 18 places to the side panels. 3.4.6 Rifle butt holder assembly. The rifle butt holder assembly shall be fabricated from Sheet Aluminum Alloy, 5052-H32, .O63 inch thick, QQ-A-250/8 and shall be mounted on the side panels with four bolts. The assem

31、bly shall be coated by dipping in Plastisol Plastic Coating, Type I, Class I, per -MIL-P-20689 requirements (see 4.4.6). 3.4.7 Muzzle clip assembly. The muzzle clip assembly base clip shall be -fabricated from Sheet Aluminum Alloy, 5052-H32, .125 inch thick, QQ-A-250/8. The spring clip shall be fabr

32、i- cated in accordance with MIL-C-24066/2-336 and shall be riveted s to the base clip. . The assembly shall be coatedby dipping in Plastisol Plastic Coating, Type I, Class I, per MIL-P-20689 requirements (see 44.6). The base clip shall be bolted in four places to the side panels. 3.4.8 Strap assembl

33、y; tie down. The strap assembly, tie down shall be fabricated from Strap, Webbing, MIL-W-40 88, Type II, Class I, 2500 lbs minimum strength, color Gray; Strap Webbing, MIL-W-4088 Type XXVII, Class I, 6500 lbs minimum strength, color Gray; sewn with Thread per Fed Spec. V-T-295, Type II, Class A, Typ

34、e B, color Black per-FED-STD-595. Attaching hardware will consist of Rotating End Fitting; Plate, Threading; Hook, Flat; and Fastener, Flat Hook. Attaching hardware shall be Cold Rolled Steel, 300 lbs minimum strength with HD Zinc Plate Bronze Chromate Finish. The strap assembly shall be fabricated

35、to have a minimum strength of 300 lbs (see 4.4.7). 3.4.9 Bracket mounting. The bracket mounting, shall be fabri- cated of Angle, Aluminum Alloy, 6061-T6, QQ-A-200/8 and shall be securely bolted to the frame in four places to such a degree of accuracy ensuring it will align to the footprint as descri

36、bed in Figure 1 (see 4.4.8). 3.4.10 Decal. The decal shall be fabricated from .O03 inch thick aluminum alloy foil, photographically sensitized, and with adhesive back in accordance with MIL-P-15024, Type G and MIL-P- 19834, Type II. Requirements and methods of marking the decal - 5 Provided by IHSNo

37、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-29 44 2 (MC) shall be in accordance with MIL-STD-130. Unless otherwise specified all characters shall be .O93 inch high, color shall be natural in accordance with MIL-P-15024, Style III. Color style shall be as pe

38、r MIL-P-15024, Style III, Lusterless Black Black- ground in accordance with FED-STR-595, Color No. 37038 when inspected as specified in 4.4.6. The decal shall be attached to the front left hand side of the shelf and 3.00 inches from edge of the assembly (see 4.4.9). 3.5 Finish. 3.5.1 Cleaninq. Prior

39、 to painting all surfaces shall be 3.5.2 Priming. After all surfaces have been cleaned as required cleaned and treated per MIL-T-704, Type G, and MIL-C-5541, Class 3. they shall be primed per MIL-P-53022, with a minimum dry film thickness of ,001 inch in one coat. 3.5.3 Paintine. Final finish painti

40、ng shall have a minimum dry coat fih thickness of .O018 inch in two coats per MIL-(2-22750, Type II, Color-No. 24533 per FED-STD-595 (see 4.4.12). shall be functionally and dimensionally interchangeable. Inter- changeable parts are defined as two or more like parts possessing such functional and phy

41、sical characteristics as to be equivalent in performance and durability, and capable of being exchanged one for the other without alteration of the parts themselves or adjoin- ing parts and without selection for fit or performance. 3.6 Interchangeability. All parts having the same part number * 3.7

42、Workmanship. The Module Assembly, Personnel Storage, shall meet all design, fabrication, assembly, and finish requirements of this specification. Particular attention shall be given to; removal of burrs and sharp edges; accuracy of dimensions; thorough- ness of welding; painting; .alignment; tightne

43、ss of screws, bolts, and rivets. Failure to ensure these measures have been taken will be considered adequate basis for rejection of items being of inferior quality for the purpose intended. 4 . QUALITY ASSURANCE PROVIS IONS 4.1 Responsibility for inspection. Unless otherwise specified in the contra

44、ct or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the perlormance of the inspection requireme

45、nts specified .herein, unless disapproved by the Government. The - Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 9 Provided by IHSNot for R

46、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-274112 71 7779706 02905611 1 W MIL-M-29442 (MC) 4.1.1 Responsibility for compliance. All items must meet all. requirements of section 3 and 5. The inspection set forth in this specification shall become a part of the con

47、tractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contr

48、act. Sampling in quality conformance does not authorize. submission of known defective material, either indicated or actual, nor does it commit the Government to accep- tance of defective material. 4.1.2 Test equipment and inspection facilities. When specified (see 6.2) the contractor shall insure t

49、hat test and inspection facilities of sufficient accuracy, quality and quantity are estab- lished and maintained to permit performance of required inspections. 4.2 Classification of inspections. The inspections specified herein are classified as follows: a. First article inspection. First article inspection consists of examinations and tests performed on samples which are representative of the production item after award of a contract to determine