NAVY MIL-P-18472 G-1989 PUMPS CENTRIFUGAL CONDENSATE FEED BOOSTER WASTE HEAT BOILER AND DISTILLING PLANT《废热锅炉和蒸馏设备的锅炉给水的浓缩物离心泵》.pdf

1、a w e 0 a - E-35-P/ MIt-P-18472G 43 m 7779706 0273280 9 m IINCH-POUNDI MIL-P-l8472C(SH) 24 APRIL 1989 SUPERSEDING 15 December 1972 (See 6.9) MIL-P-l8472F(SHIPS) MILITARY SPECIFICATION PUMPS, CENTRIFUGAL, CONDENSATE, FEED BOOSTER, WASTE HEAT BOILER, AND DISTILLING PLANT This specification is approved

2、 for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers centrifugal pumps for condensate, boiler feed booster, waste heat boiler, and distilling plant servi

3、ces on board Naval ships. overboard and drain service. Distilling plant pumps covered herein are distillate, brine 1.2 Classification. The pumps shall be of the following classes as speci- fied (see 6.2). Class D-1 - Auxiliary condensate and distilling plant pumps - more than Class. D-2 - Main and a

4、uxiliary condensate pumps - 18-inch or less Class E - Main and auxiliary feed booster pumps. 18 - inch submergence. submergence. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent

5、 specified herein. otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). Unless Beneficial comments (reeommendations, additions, deletio

6、ns) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SFA 5523, Department of the Navy, Washington, BC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at th

7、e end of this document or by letter. THIS DOCUMENT CONTAINS 40 PAGES. AMCC N/A FSC 4320 DICTRIBUTION STATEMENT A. Approved fif public release; distribution is unlimited. - -% - . / P, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L472G 43 W 7

8、77770b 0273281 O M SPECIFICATIONS FEDERAL FF- B- 17 1 FF- B - 18 5 FF- B- 18 7 QQ-C-390 QQ - N- 2 8 1 QQ - N- 2 8 6 QQ - N - 2 8 8 QQ-S-763 TT-P-645 MILITARY MIL- S - 901 MIL- E- 917 MIL-S-1222 MIL-C-2212 MIL-P-15024 MIE-P-15024/5 MIL-E-15090 DOD-P-15328 MS 16 142 MIL-T-16420 MIL-S-16993 MIL-M-17060

9、 MIL-L-17331 MIL-M-17413 MIL-T-17523 MIL-P-17881 MIL-B-17931 MS 18229 MIL- G- 189 16 - Bearings, Ball, Annular (General Purpose). - Bearings, Roller, Cylindrical; and Bearings, Roller, Self-Aligning. - Bearing, Roller, Tapered. - Copper Alloy Castings (Including Cast Bar). - Nickel-Copper Alloy Bar,

10、 Rod, Plate, Sheet, Strip, Wire, Forgings, and Structural and Special Shaped Sections. N05500). Alloy Castings. Resisting. - Nickel-Copper-Aluminum Alloy, Wrought (UNS - Nickel-Copper Alloy and Nickel-Copper-Silicone - Steel Bars, Wire, Shapes, and Forgings, Corrosion - Primer, Paint, Zinc Chromate,

11、 Alkyd Type. - Shock Tests, H.I. (High-Impact); Shipboard Machinery, Equipment and Systems, Requirements for. (Naval Shipboard Use). Screws and Nuts. Associated Switching Devices. Equipment. - Electric Power Equipment, Basic Requirements - Studs, Bolts, Hex Cap Screws, Socket Head Cap - Controllers,

12、 Electric Motor A.C. or D.C., and - Plates, Tags and Bands for Identification of - Plates, Identification. - Enamel, Equipment, Light-Gray (Formula No. ill). - Primer (Washl, Pretreatment (Formula No. 117 for - Boss, Gasket Seal, Straight Thread Tube Fitting, - Tube, Copper-Nickel Alloy, Seamless an

13、d Welded, - Steel Castings (12 Percent Chromium). - Motors, 60 Hertz , Alternating Current , Integral- - Lubricating Oil, Steam Turbine and Gear, Moderate - Motors, Direct-Current, Integral H.P., Naval - Turbine, Steam, Auxiliary (and Reduction Gear) - Pumps, Centrifugal, Boiler Feed, (Multi-Stage),

14、 - Bearings, Ball, Annular, for Quiet Operation. - Plug for “O“ Ring Gasket. - Governors, Steam Driven Pump, Pressure Regulating, Metals) (Metric). Standard Dimensions for. (Copper Alloy Nos. 715 and 706). Horsepower, Shipboard Use. Service. Shipboard. Mechanical Drive. Naval Shipboard. 2 Provided b

15、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L472G 43 7777906 02GFF 2GF MILITARY (Continued) MIL-C-20159 - Copper-Nickel Alloy Castings (UNS No. C96200 and MIL-P-22302 - Pumps, Centrifugal, Boiler Feed, Single Stage. MIL-S-22473 - Sealing, Locking, an

16、d Retaining Compounds: (Single-Component). MIL-C-23233 - Couplings for Propulsion Units, Auxiliary Turbines and Line Shafts Naval Shipboard. MIL-L-24131 - Lubricant, Colloidal Graphite in Isopropanol. DOD-G-24508 - Grease, High Performance, Multi-Purpose (Metric). C96400). STANDARDS FEDERAL FED-STD-

17、H28 - Screw-Thread Standards for Federal Services. FED-STD-H28/2 - Screw-Thread Standards for Federal Services Section 2 - Unified Inch Screw Threads - UN and UNR Thread Forms. MILITARY MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally Exci

18、ted). MIL-STD-271 MIL-STD-278 MIL-STD-438 - Schedule of Piping, Valves, Fittings, and Associ- ated Piping Components for Submarine Service. MIL-STD-740-1 - Airborne Sound Measurements and Acceptance Criteria of Shipboard Equipment. MIL-STD-740-2 - Structureborne Vibratory Acceleration Measurements a

19、nd Acceptance Criteria of Shipboard Equipment. MIL-STD-777 - Schedule of Piping, Valves, Fittings, and Associ- ated Piping Components for Naval Surface Ships. DOD-STD-1371 - Inspection Procedure for Use of Anaerobic Thread Locking Compounds with Studs. MIL-STD-1472 Systems, Equipment and Facilities.

20、 - Requirements for Nondestructive Testing Methods. - Welding and Casting Standard. - Human Engineering Design Criteriafor Military (Unless otherwise indi_cated, copies of federal and military specifications and standards are available from the Naval Publications and Forms Center (ATTN: NPODS) , 580

21、1 Tabor Avenue, Philadelphia, PA 19120-5099 .) 2.1.2 Government drawings and Dublications. The following Government drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS NAVAL SEA SY

22、STEMS COMMAND (NAVSEA) NAVSHIPS B-153 - Packing and Gaskets, Application of. NAVSHIPS B-214 - Root Connections for Attaching Pipe. NAVSEA 810-1385850 - Piping, Pressure Instrument for All Services. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

23、P-1q72G 43 7777906 0273283 q MIL-P-l8472G(SH) PUBLICATIONS NAVAL SEA SYSTEMS COMMAND (NAVSEA) NAVSEA 0900-LP-001-7000 - Fabric tion and Inspe Piping Systems. tion of Brazed (Application for copies should be addressed to the Naval Publications and Forms Center (ATTN: NPODS), 5801 Tabor Avenue, Philad

24、elphia, PA 19120-5099.) 2.2 Non-Government rmblications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless ot

25、herwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) General Application. (DoD adopted) A 27 - Standard Specification for Steel Castings, Carbon, for A 36 - Standard

26、Specification for Structural Steel. (DoD adopted) A 276 - Standard Specification for Stainless and Heat-Resisting Steel Bars and Shapes, A 285 - Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength. (DoD adopted) A 487 - Standard Specification for S

27、teel Castings Suitable for Pressure Service. A 515 - Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service. (DoD adopted) Percent), Hot-Rolled Sheet and Strip Commercial Quality. (DoD adopted) A 743 - Standard Specification for Castings, Ir

28、on-Chromium, Iron- Chromium-Nickel, Nickel-Base, Corrosion Resistant, for General Application, (DoD adopted) Nickel-Base, Corrosion Resistant, For Severe Service. (DoD adopted) - Standard Specification for Steam or Valve Bronze Castings. (DoD adopted) (DoD adopted) A 569 - Standard Specification for

29、 Steel, Carbon (0.15 Maximum, A 744 - Standard Specification for Castings, Iron-Chromium-Nickel, B 61 B 164 - Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire, (DoD adopted) (DoD adopted) General Applications. (DoD adopted) B 369 - Standard Specification for Copper-Nicke B 584 - Sta

30、ndard Specification for Copper Alloy Alloy Castings. Sand Castings for (Application or copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

31、IHS-,-,-MIL-P-L472G 43 7999706 0273284 b - HYDRAULIC INSTITUTE Test Code of Standards - Centrifugal Pump Section. (Application for copies should be addressed to the Hydraulic Institute, 712 Lakewood Center N., 14600 Detroit Avenue, Cleveland, OH 44107.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) AMs 5398

32、 - Steel Castings, Sand and Centrifugal, Corrosion Resistant. (Application for copies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) (Non-Government standards and other publications are normally available from These documents also the organ

33、izations that prepare or distribute the documents. may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in

34、this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.5) in accordance with 4.3. 3.2 General characteristics. The pu

35、mps shall conform to the space and weight requirements as specified (see 6.2). the list, pitch, roll and trim conditions specified (see 6.2). Pumps shall operate continuously at any point over the entire flow range and the design Conditions as specified (see 6.2). The pump unit shall perform under 3

36、.2.1 Maintenance. The equipment specified herein will be operated, main- tained, and repaired on board Navy ships (see 6.3). Human engineering aspects, in accordance with MIL-STD-1472, shall also be fully explored and considered in the equipment design to minimize the possibility of failure through

37、improper operation and maintenance, and to preclude personnel safety hazards. Positioning and alignment of parts shall employ positive means such as shoulder, tongue and groove, or other locating techniques whereby correct reassembly is repeatedly assured. In consonance with the concept of ease of m

38、aintenance and where not already specified, the pump designer shall consider all of the following features for incorporation: Lifting lugs. Casing assembly guide pins. Alignment and positioning dowels. Jacking screws. Ease of access to couplings. Remakeable piping connections. Piping out of way of m

39、aintenance access. Ease of packing, mechanical seal, bearing, and wearing ring replacement. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-4472G 43 m 9799906 0273285 m Split casing, bearing housings, and so forth (except for submarine Guards

40、 for rotating and moving components. Warning plates to prevent casualties to equipment and personnel. Provisions for connecting instruments for performance evaluation. Attached instruments for monitoring performance. Visibility and access to attached instruments, Thoroughness of operating instructio

41、ns, Thoroughness of preventive maintenance instructions. Explicit assembly and disassembly instructions. Exploded views of critical assemblies. Adequate system diagrams. service). 3.2.1.1 Service life. Each pump shall have a service life of 30 years of which 40 percent shall be actual operation. num

42、ber of starts during the life of the pump. The parts subject to wear, deterioration, and normally requiring replacement at 3-year intervals during the service life of the pump (with the exception of packing) shall have a life of 40,000 actual operating hours. The requirement set forth above shall no

43、t be construed or interpreted as a warranty requirement, nor otherwise affect the manufacturers warranty. There shall be no limit on the 3.2.2 Shock and vibration. Pumps and drivers, all appurtenances, and controls shall pass a shock test in accordance with MIL-S-901, grade A, as specified in 4.6.3.

44、2. 3.2.2.1 Shock mount. Unless otherwise specified (see 6.2), shock mounts (resilient mounts for shock attenuation) shall not be used. When noise attenua- tion mounts are specified, the pump shall pass the specified shock test on the noise attenuatin mounts. 3.2.2.2 Mounting bolts. Bolts designed to

45、 be stressed in shear shall be installed in holes with a minimum of clearance, Hole diameters shall be not more than 1/32 inch larger than the bolts for sizes up to and including 3/4 inch, and not more than 1/16 inch larger than bolts of greater than 3/4 inch size. Mounting bolts for fastening the e

46、quipment shall conform to grade 2 or better of MIL-S-1222. 3.2.3 Vibration. Pumps shall not be damaged or caused to malfunction by either the environmental vibrations or by internally excited vibrations. furnished under this specification shall meet the requirements of MIL-STD-167-1, type I and II w

47、hen specified (see 4.6.3.4 and 6.2). Units 3.2.4 Alignment. The construction of all pumps shall be such that alignment will not be disturbed or undue stresses set up in any part by normal vibration or contraction and expansion of piping attached thereto in service. Alignment between separate compone

48、nts of a unit shall be maintained by means of keyways, rabbet or tongue and groove joints, or fitted bolts, as approved by NAVSEA. than one plane. In no case shall a piece of equipment be rigidly supported from more 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

49、se from IHS-,-,-. NIL-P-LY72G 43 477470b 02732b T 3.2.5 Noise. The construction of the equipment shall be such that noise levels during operation at the design conditions will meet the airborne noise and structureborne vibration noise requirements as specified (see 4.6.1.4 and 6.2). 3.2.6 Mountinq. Pump units shall be horizontally or vertically mounted, as specified (see 6.2). 3.2.6.1 Horizontal. Each horizontal flexible coupled pu