NAVY MIL-P-28808 A-1987 PRINTER HIGH SPEED DIGITAL DATA TT-624(V) UG《TT-624(V) UG 数字资料高速打印机》.pdf

1、- MIL-P-28808A 58 W 9999906 0354993 T MIL-P-28808A( EC) 30 April 1987 - MIL-P-Z8808(EC) 24 February 1975 MILITARY SPECIFICATION PRINTER, HIGH SPEED, DIGITAL TT-624(V)/UG DATA, This specification is approved for use by the Space and Naval Warfare Systems Command, Department of 1. SCOPE 1.1 Scope. Thi

2、s specification covers the requirements for the design, test, and manufacture of a High Speed, Digital Data Printer, TT-624(V)/UG, hereinafter referred to as the printer, generate and output hard copy of alphanumeric characters and special symbols in response to internally generated automatic signal

3、s, manually operated maintenance and operator controls, and input digital data and control signals from central processing devices, and other peripheral devices such as magnetic tape units, display units, and comnunication systems. the Navy, and is available for use by all Departments and Agencies o

4、f the Department of Defense. The printer will 2. APPLICABLE DOCUMENTS 2.1 Government documents. -7 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the- extent specified herein. Unless otherwise specified, the issues of these documen

5、ts,!. shall be those listed in the issue of the Department of Defense Index of Specifications and Standards - 1 (DoDISS) and supplement thereto cited in the solicitation. SPECIFICATIONS FEDERAL FF-B-171 Bearings, Ball, Annular, (General Purpose) FF-B-185 FF-B-187 Bearings, Roller Tapered uu-P-547 Pa

6、per, Teletypewriter, Rol 1 Bearings, Roller, Cylindrical; And Bearings Roller, Self-Aligning MIL I TARY MIL-S-901 MIL-S-3786 MIL-P-15024 MIL-15090 MIL-S-15291 MIL-F-15733 MIL-E-16400 MIL-M-17059 Shock Tests, H.I. (High-Impact); Shipboard Machinery, Equipment And Systems, Requirements For Switches, R

7、otary (Circuit Selector, Low Current Capacity) General Specification For Plates, Tags, And Bands For Identification Of Equipment Enamel, Equipment, Light-Gray (Formula Na. 111) Switches, Rotary, Snap Action And Detent/Spring Return Action, General Specification For Filters, And Capacitors, Radio Fre

8、quency Interference, General Specification For Electronic, Interior Comnunication And Navigation Equipment, Naval Ship And Shore: General Specification For Motors, 60-Cycle Al ternating-Current, Fractional HP (Shipboard Use) I Beneficial comments (recommendations, additions, deletions) and any perti

9、nent data which may be of use in improving this document should be addressed to: Comnander, Space and Naval Warfare System Command (SPAWAR 003-1211, Washington, DC 20363-5100, by using the self-addressed Standardization Document. Improvement Proposal (DD Form 1426) appearing at the end of this docum

10、ent, or by letter. AMSC N/A FSC 5815 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. , c THIS DOCUMENT CONTAINS Alternating-Current, Integral HP, (Shipboard Use) Motors; Direct Current, Integral HP, Naval Shipboard Electronic And Electrical Equipment, Accessories, A

11、nd Provisioned Items (Repair Parts): Packaging Of Motor, Direct Current, Fractional HP (Shipboard Use) Switches, Rotary, Multiple And Selector, General Specification For Insulating Compound, Electrical (For Coating Printed Circuit Assemblies) Sampling Procedures And Tables For Inspection By Attribut

12、es Definitions Of And Basic Requirements For Enclosure For Electric And Electronic Equipment Qual i ty Assurance Terms And Defini ti ons Mechanical Vibrations Of Shipboard Equipment (Type I - Excited Environmental And Type II - Internally) Military Communication System Technical Standards Electronic

13、 Equipment Parts (Selected Standards) Standard General Requirements For Electronic Equipment Electromagnetic Emission And Susceptibility Requirements For The Control Of Electromagnetic Interference Electromagnetic Interface Characteristics, Measurement Of Mai ntai nabi 1 i ty Veri fication/Demonstra

14、tion/Eval uation Airborne And Structureborne Noise Measurements And Acceptance Cri teria Of Shipboard Equipment Reliability Design Qualification And Production Acceptance Tests: Exponential Distribution Environmental Test Methods And Engineering Guidelines Parts Control Program Standard General Purp

15、ose Electronic Test Equipment , 2.1.2 Other Government publications. specification to the extent specified herein. The following other Government publications form a part of this Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. PUBLICATIONS MILITARY NA

16、TIONAL SECURITY AGENCY (NSA) NACSIM 5100A Compromi sing Emanations Laboratory Test Standard El ectromagnetics SPACE AND NAVAL WARFARE SYSTEMS COMMAND (SPAWAR) EE-161-NA-OMI-010/EiiO-TT-624 Teleprinter TT-624( V) /UG, TT-624( V) l/UG, (Basic Manual 1 TT-624A( V)/UG, TT-6246, TT-624C( V)/UG, TT-624D(

17、V)/UG NAVELEX 0967-LP-544-0030 Teleprinter TT-624B(V)Z/UG (188B Parallel Odd Interface) NAVELEX 0967-LP-544-0050 Teleprinter TT-624(V) 5/UG (Serial TA2 Interface) NAVELEX 0967-LP-544-0060 NAVELEX 0967-LP-544-0090 Teleprinter TT-624(V)6/UG (NTDS SLOW, 8 Bit Interface) Teleprinter TT-624(V)8/UG (NTDS

18、FAST, 16 Bit Interface) NAVELEX 0967-LP-544-0100 Teleprinter TT-624(V)9/UG (Serial ITA 2/USQ 69 Interface) (Copies of specifications, standards, and pub1 ications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed

19、 by the contracting officer. 1 P 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, except for associated detail specifications, specification sheets, or MS standards, the text of this specification shall take precedence, super

20、sede applicable laws and regulations, unless a specific exemption has been obtained. Nothing in this specification, however, shall 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a MIL-P-288OA 58 777970b 0154775 3 W MIL-P-28808A( EC) 3. REQUIREMENT

21、S 3.1 General. The printer shall be in accordance with MIL-E-16400, except as hereinafter specified. 3.1.1 First article. When specified in the contract or purchase order, a sample shall be subjected 3.1.2 Standard Sam le. A sample, representative of the type of copy to be obtained when using the 3.

22、2 Printer description. to first article inspection (see 4.3 and 6.3). printer, shall be provided as Government-furnished infomation. a communication terminal device. The printer shall consist of a cabinet, printer mechanics, electronic control, buffering units, and power supply. No controller shall

23、be required for standard installation. The printer shall interface with the ANIUYK-LO digital data computer. The printer shall be a high speed printer which provides for application as 3.2.1 Printer external interface options. Printer external interface options shall be as specified in 3.2.1.1 throu

24、gh 3.2.1.8. i 3.2.1.1 TT-( )(V)l/UG: standard transistor-to-transistor logic (TTL) American Standard Code for Information Interchange (ASCII) interface. The printer shall interface with the AN/U VKZTa ready-response mode parallel ASCII levels. The printer shall be capable of printing the sixty-four

25、letter ASCII subset specified in TABLE I. as specified in TABLE II. AN/UYK-LO in demand-responseevels. printing the sixty-four letter ASCII subset specified in TABLE I. The printer shall interface via a MS3102R-36-10PZ connector (48 pins) as specified in TABLE III. The printer shall interface via a

26、MS3102R-28-21PZ connector (37 pins) 3.2.1.2 TT( )(V)P/UG: MIL-STD-188 paraliel ASCII interface. The printer shall interface with the The printer shall be capable of TABLE I. ASCII 64-symbol subset. Col umn b7 b6 b5 O O O O 6 1 1 O A B C O b4 b3 b2 bl A -i; R S 3 =E O100 D E F G H 18 1 o o 11 I y 19

27、1 o 1 o I LFi/ J 2 I 10 1 o 111 K L M 1 I 13 N O 1, Nonprinting control characters 71 Is the twenty-sixth character, in lieu of a space, in the printed set, indicates parity error 21 Replaces the specified in MIL-STD-188 (row 14) and indicates an illegal character 3 Provided by IHSNot for ResaleNo r

28、eproduction or networking permitted without license from IHS-,-,-MIL-P-ZDA 58 7777906 OL5477b 5 MIL-P-28808A( EC) TABLE II. TT-624(Vl) pin-outs cable connector MS3106F28-21-SZ. Connector P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12

29、13 14 15 16 17 18 19 20 21 22 23 24 4 Function CHAR DEMAND CHAR DEMAND RET. CHAR STROBE CHAR STROBE RET. BIT 1 BIT 1 RET. BIT 2 BIT 2, RET. BIT 3 BIT 3 RET, BIT 4 BIT 4 RET, BIT 5 BIT 5 RET. BIT 6 BIT 6 RET. BIT 7 BIT 7 RET. BIT 8 (PARITY BIT OR BITP) OR BITP) BIT 8 RET. (PARITY M CLEAR M CLEAR RET.

30、 PFD (PAPER FEED) PFD (PAPER FEED) RET. CABLE SHIELDS (CABINET GROUND CONNECT POINTS) UNUSED PIN Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y MIL-P-2OA 5 W 7779706 0354777 7 Connector i No. I Function MIL-P-28808A( EC) TABLE III. TT-624(V2) pin-

31、outs cable connector MS3106F36-1D-SZ. Connector P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 Pin k b E A 4 4 J C M F H O R K N T - - No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Function CHAR DEMAND - CHAR DEMAND RET. CHAR STROBE CHAR STROBE RET. READY READY RET. BIT 1 BIT 1 RET. BIT 2 BIT 2 RET. B

32、IT 3 BIT 3 RET. BIT 4 BIT 4 RET. BIT 5 BIT 5 RET, 3.2.1.3 TT-( )(V)5/UG: serial baudot interface. The printer shall interface with AN/UYK-PO in a demand response mode, MIL-STD-188 serial baudot leveT. sixtv-four letter ASCII subset soecified in TABLE I. The winter shall interface via a MS3102R-28-21

33、PZ The printer shall be capable of printing the connctor (37 pins) as specifiedin TABLE IV. P2 Pin G P2 Pin B P2 Pin H P2 Pin J DEMAND DEMAND RET. DATA DATA RET, 3.2.1.4 TT-( )(V)6/UG: 8-bit Naval Tactical Data System (NTDS) slow interface. The printer shall interface with the AN/UYK-PO in a demand

34、response mode, NTDS slow 8-bit parallel format. shall be capable of printing the sixty-four letter ASCII subset specified in TABLE I. interface via a MS3102R-36-10PZ connector (48 pins) as specified in TABLE V. The printer The printer shall 5 Provided by IHSNot for ResaleNo reproduction or networkin

35、g permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-28808A( EC) 3.2.1.5 TT-( )(V)8/UG: 16-bit NTDS fast interface. The printer shall interface with the AN/UYK-LO in a demand-response mode; NTDS f ast 11-bit

36、parallel will perform a form feed upon receipt of a FIGURES-SPACE-FIGURES character sequence in lieu of the upper case H character. capable of printing the sixty-four letter ASCII subset specified in TABLE I. via a MS3102R-36-10PZ connector (48 pins) as specified in TABLE VI. The printer shall be Th

37、e printer shall interface 3.2.1.6 TT-( )(V)9/UG serial ITA 2/USQ 69 interface. The printer shall interface with the AN/UYK-20 through the m/USQ-69 Data Terminal in a multidrop (daisy chain) configuration so that the printer shall print-data received in a serial asynchronous mode directly from the AN

38、/USQ-69. used in an additional capacity, it shall be operator-selectable to receive the print data directly from the AN/UYK-20 in serial ITA 2 mode as specified in 3.2.1.3. The printer shall interface via a MS81511/01EF01Pl and MS81511/01EFOlP2 connector (85 pins) as specified in TABLE VII. So that

39、the printer can be TABLE VI. TT-624(V8) pi n-outs cable connector MS3106F36-10-SZ. Connector P2 P2 P2 P2 - P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 Pin k b E A n e E - - - - V - D L P W U C - Y f a h S X U - - - - - - 1 W 2 - - J No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

40、 19 20 21 22 23 24 25 7 Function ODR ODR RET. ODA ODA RET. EFA EFA RET. ERS ERS RET, BIT 1 BIT 1 RET. BIT 2 BIT 2 RET. BIT 3 BIT 3 RET. BIT 4 BIT 4 RET. BIT 5 BIT 5 RET. BIT 6 BIT 6 RET, BIT 7 BIT 7 RET. BIT 8 BIT 8 RET. BIT 9 Provided by IHSNot for ResaleNo reproduction or networking permitted with

41、out license from IHS-,-,-MIL-P-2880A 58 W 777770b OL55000 L W MIL-P-28808A( EC) TABLE VI. TT-624(V8) pin-outs cable connector MS3106F36-10-SZ. - (Continued) Connector P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 Pin C M F H O R K N T d V Q X S Z m t j r 9 9 - - - - NO. 26 27 28 29

42、30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Function BIT 9 RET. BIT 10 BIT 10 RET. BIT 11 BIT 11 RET, BIT 12 BIT 12 RET. BIT 13 BIT 13 RET. BIT 14 BIT 14 RET. BIT 15 BIT 15 RET, BIT 16 BIT 16 RET; EIE EIE RET, EIA EIA RET. EIR EIR RET. TABLE VII. TT-624(V9) pin-outs cable connector MS81511/56

43、FFOl-S2 (for matin with connector P3) and MS81511/56FF 01-S1 (for mating with connector P2). (Conti(tnued) Connector P3 P3 P3 P3 P3 P3 P3 Pin 20 28 11 85 38 83 27 No. Function RCV DATA (OUT OF 9/UG) L/ 6-LINE MIT DATA (INTO 9/UG) SIGNAL GROUND A-LINE C-LINE D-LINE Provided by IHSNot for ResaleNo rep

44、roduction or networking permitted without license from IHS-,-,-MIL-P-2OA 58 7779706 015500L 3 Pin 48 MIL-P-28808A( EC) No. 8 TABLE VII. TT-624(V9) pin-o!t? cable connector MS81511/56FFOl-S2 (for matins with connector P3) and MS81511/56-F 01-S1 (for mating with connector P2). (Continued) Connector P3

45、 P3 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 P2 3 16 6 7 30 . 24 40 17 23 1, 2, 4, 5, 8-15, 18-22, 25-29, 31-39, 41-85 1, 2, 4, 5, 8-15, 18-22, 25-29, 31-39, 41-85 Function E-LINE UNUSED PIN LOCATIONS RCV DATA (OUT OF 9/UG) i/ B-LINE XMIT DATA (INTO 9/UG) SIGNAL GROUND A-LINE C-LINE D-LINE E-LINE K-LINE (NO CO

46、NNECT) UNUSED PIN LOCATIONS DATA (INTO 9/UG) 21 DEMAND SIGNAL GROUND RESERVED PIN LOCATIONS - (NOT USED WITH 9/UG IN ITA MODE) UNUSED PIN LOCATIONS L/ The 9/UG can be internally configured to operate in one of two modes. 9/UG has two input/output connectors to allow daisy chaining (or busing) of per

47、ipherals when used in the USQ mode. Only one connector is utilized when the 9/UG is used in the US9 mode and the 9/UG is the only unit in the chain or the last unit in the chain. Both connect points are functionally identical. The differences are the connector shell keying and signal pin-out. The 9/

48、UG can be internally configured to operate in one of two modes. The 9/UG has two connectors to allow daisy chaining (or busing) of peripherals when used in the USQ mode. Only one connector is utilized when the 9/UG is used in the ITA mode. The differences are the connector shell keying and signal pi

49、n-out. This is based on the use of P2 of the 9/UG as the connect point for ITA mode operation. The 21 Both connect points are functionally identical. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-2BOA 58 777770b 0155002 5 6- MIL-P-28808A( EC) 3.2.1.7 External interfaces. All printer interfaces specified in 3.