1、 Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05Q, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. Since contact
2、 information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 8030 INCH-POUND MIL-PRF-16173E(SH) w/INT. AMENDMENT 1 7 September 2006 USED IN LIEU OF MIL-PRF-16173E 6 January 1993 PERFORMANCE SPECIF
3、ICATION CORROSION PREVENTIVE COMPOUND, SOLVENT CUTBACK, COLD-APPLICATION This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers solvent-dispersed corrosion preventive compounds that deposit thin, easily remov
4、able films after evaporation of solvent. 1.2 Classification. Corrosion preventive compounds covered by this specification are furnished in the following classes and grades, as specified (see 6.2). 1.2.1 Classes. The classes of the corrosion preventive compounds are designated by Class I (High volati
5、le organic compounds (VOC) or “Class II“ (Low VOC) as follows: Class I - High VOC - VOC exceeding 2.8 pounds per gallon (lbs/gal) (340 grams/liter). Class II - Low VOC - VOC not exceeding 2.8 lbs/gal (340 grams/liter). 1.2.2 Grades. The grades of the corrosion preventive compound are the following:
6、Grade 1 Hard film (175 degrees Fahrenheit (F) 80 degrees Celsius (C) minimum flow point of solvent deposited film). Grade 2 Soft film. Grade 3 Water displacing, soft film. Grade 4 Transparent, non-tacky film. Grade 5 Low pressure steam removable film. 2. APPLICABLE DOCUMENTS 2.1 General. The documen
7、ts listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this li
8、st, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and hand
9、books form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16173E(SH) w/ INT AM
10、ENDMENT 1 2 SPECIFICATIONS FEDERAL A-A-1671 - Tape, Gummed (Paper, Reinforced, Laminated). O-M-232 - Methanol (Methyl Alcohol). P-D-680 - Dry Cleaning and Degreasing Solvent. QQ-A-250 - Aluminum and Aluminum Alloy Plate and Sheet: General Specification for. QQ-A-250/5 - Aluminum Alloy Alclad 2024, P
11、late and Sheet. QQ-S-700 - Steel Sheet and Strip, Medium and High Carbon. RR-S-366 - Sieve, Test. TT-E-485 - Enamel, Semigloss, Rust-Inhibiting. TT-N-95 - Naphtha; Aliphatic. TT-T-291 - Thinner, Paint, Mineral Spirits, Regular and Odorless. PPP-C-96 - Cans, Metal, 28 Gage and Lighter. PPP-F-320 - Fi
12、berboard; Corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes. PPP-D-729 - Drums, Shipping and Storage. Steel, 55-Gallon (208 Liters). PPP-P-704 - Pails, Metal: (Shipping, Steel, 1 through 12 Gallons). MILITARY MIL-L-17331 - Lubricating Oil, Steam Turbine and Gear, Moderate Service.
13、MIL-A-18001 - Anodes, Corrosion Preventive, Zinc; Slab Disc and Rod Shaped. MIL-L-19140 - Lumber and Plywood, Fire-Retardant Treated. MIL-A-22262 - Abrasive Blasting Media Ship Hull Blast Cleaning. MIL-I-45208 - Inspection System Requirements. STANDARDS FEDERAL FED-STD-313 - Material Safety Data, Tr
14、ansportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities. MILITARY MIL-STD-147 - Palletized Unit Lands. MIL-STD-290 Packaging of Petroleum and Related Products. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/as
15、sist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawing, and publications. The following other Government documents, drawings, and publications form a part of this document to the exte
16、nt specified herein. Unless otherwise specified, the issues are those cited in the solicitation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16173E(SH) w/ INT AMENDMENT 1 3 U.S. ENVIRONMENTAL PROTECTION AGENCY (EPA) 40 Code of Federal Reg
17、ulations (CFR) Ch. 1, Part 60, Appendix A, Method 24 - Determination of Volatile Matter Content, Water Content, Density, Volume Solids and Weight Solids of Surface Coatings. OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Occupational Health and Safety Administration, 29 CFR Parts 1910, 1915, 1
18、917, 1918, 1926, and 1928 - Hazard Communication Act, Final Rule. (Unless otherwise indicated, copies of other Government documents are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.) 2.3 Non-Government publications. The following documents for
19、m a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) B 117 - Standard Method of Salt Spray (Fog) Testing. B 121 - Standard Specification f
20、or Leaded Brass Plate, Sheet, Strip, and Rolled Bar. D 16 - Standard Terminology Relating to Paint, Varnish, Lacquer, and Related Products. D 86 - Standard Test Method for Distillation o Petroleum Products. D 93 - Standard Test Methods for Flash Point by Pensky-Martens Closed Tester. D 822 - Standar
21、d Practice for Conducting Tests on Paint and Related Coatings and Materials Using Open-Flame Carbon-Arc Light and Water Exposure Apparatus. D 874 - Standard Test Method for Sulfated Ash from Lubricating Oils and Additives. D 937 - Standard Test Method for Cone Penetration of Petrolatum. (DoD adopted
22、) D 1748 - Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet. (DoD adopted) D 2369 - Standard Test Method for Volatile Content of Coatings. D 3278 - Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus. D 3951 - Standard Practice for Commerc
23、ial Packaging. (DoD adopted) D 4057 - Standard Practice for Manual Sampling of Petroleum and Petroleum Products. G 23 - Standard Practice for Operating Light-Exposure Apparatus (Carbon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials. (DoD adopted) (Application for copies shoul
24、d be addressed to the American Society for Testing And Materials, 1916 Race Street, Philadelphia, PA 19103-1137.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) AMS 4377 - Magnesium Alloy Sheet and Plate 3.0A1-1.OZn (AZ31B-H24) Cold Rolled, Partially Annealed. Provided by IHSNot for ResaleNo reproduction or
25、networking permitted without license from IHS-,-,-MIL-PRF-16173E(SH) w/ INT AMENDMENT 1 4 (Application for copies should be addressed to the Society of Automotive Engineers, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) United Nations (UN) UN - Performance Oriented Packaging. (Application for
26、 copies should be addressed to Labelmaster, 5724 North Pulaski Road, Chicago, IL 60646.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other inf
27、ormational services.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated detail specifications, specifications, specification sheets or MS standards), the text of this document takes precedence. Nothing
28、 in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Qualification. The corrosion preventive compound furnished under this specification shall be products which are authorized by the qualifying activity for listing
29、on the applicable qualified products list at the time of award of contract (see 4.3 and 6.4). 3.1.1 Classification. Unless otherwise specified (see 6.2), preservatives shall conform to the classification contained herein (see 1.2). The selection o class and grade of preservatives shall be based on p
30、articular application. removal, or use without causing damage to the specific items to which they are applied (see 6.1). 3.2 Material. The corrosion preventive compound shall be composed of a nonvolatile base material dispersed in petroleum solvent in order to form a fluid formulation conforming to
31、this specification. The compound shall be uniform, free from grit, abrasives, water, chlorides, or other impurities. 3.2.1 Toxicity. When evaluated as specified in 4.8, the materials used in the preventive compound unless specific material maximum levels are cited herein shall have no known carcinog
32、enic or potentially carcinogenic materials identified by Occupational Safety and Health Administration (OSHA) regulated carcinogens, or International Agency for Research on Cancer (IARC) latest monographs, or and the latest annual report of the National Toxicology Program (NTP). The manufacturer is
33、responsible for maintaining carcinogenic free materials. The manufacturer shall certify that the preventive compound does not contain the following materials in excess of 0.05 percent by weight of the dry preventive compound asbestos or asbestos-form pigments, benzene, toluene, chlorinated solvents,
34、 hydrolyzable chlorine derivatives, lead, chromium, mercury, and nitrosamines. The manufacturer shall also certify that the product unless specific material maximum levels are cited herein does not have known or suspected carcinogens intentionally added to the formulation and when known or suspected
35、 carcinogens are/may be present, as a result of being a trace, impurity in another ingredient(s) the concentration of the agent in the final product must not exceed the in excess of 0.05 percent by weight of the dry preventive compound. A certificate of compliance shall be provided with each lot shi
36、pped (see 4.1.3 and 6.3). The preventive compound shall have no adverse effect on the health of personnel when used for its intended purpose. Questions pertinent to this toxic effect shall be referred by the contracting activity to the qualifying activity. The qualifying activity will act as advisor
37、 to the contracting activity. The qualifying activity will arrange for review of questions by the appropriate departmental medical service. The contracting activity shall be provided with a copy of Navy Environmental Health Center (NEHC) findings. The NEHC findings shall be included with each unit o
38、f issue of material covered by this specification (see 5.6). 3.2.2 Material safety data sheet (MSDSD). The contracting activity shall be provided a material safety data sheet at the time of contract award. The MSDS shall be provided in accordance with OSHA section 1910.1200, 29 CFR CH XVII and found
39、 as part of FED-STD-313. OSHA section 1910.1200 requires reporting threshold criteria for known or suspected human carcinogens on MSDS 0.1% or greater. The KSDS shall be included with each unit of issue of material covered by the specification (see 5.5 and 6.5). 3.3 Film characteristics. The film ch
40、aracteristics shall be as specified in 3.3.1 and 3.3.2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-16173E(SH) w/ INT AMENDMENT 1 5 3.3.1 Grades 1. 2. 3. 4. and 5. The compounds shall readily wet the surfaces of the test panels and upon e
41、vaporation of the solvent the resultant coating shall be continuous. Upon completion of the accelerated weathering (grade 1) and shed storage (grades 2, 3, 4, and 5) tests, the specimens shall show no evidence of cracking. Specimens that show evidence of checking, alligatoring, or other irregulariti
42、es shall be evaluated as specified in 4.6.11.7. (Refer to ASTM D 16 for definition of terms.) 3.3.2 Grade 4 only. The compound shall be transparent during the protective life of the coating (see 4.6.16). 3.4 Nonvolatile and volatile organic content (VOC). 3.4.1 Nonvolatile content. The nonvolatile c
43、ontent (percent by weight) for each grade and class of product will be established when qualification tests are conducted. The nonvolatile content of any succeeding lot of product shall be not greater than 5 percent lower nor 10 percent higher than the established value, based on the nonvolatile as
44、received as being 100 percent (see 4.6.5.1). 3.4.2 Volatile organic content (VOC). When tested as specified in 4.6.5.2, the VOC for class I compounds may exceed 2.8 lbs/gal (340 grams/liter) and class II VOC compounds shall not exceed 2.8 lbs/gal (340 grams/liter). 3.5 Solvent distillation end point
45、. The solvent employed shall possess a maximum distillation end point of 410F (210C) (see 4.6.1). 3.6 Discernibility. Grades 1 and 2 shall be permanently discernible on the preserved item and grades 3 and 5 shall be discernible for at least two weeks after application when allowed to stand in a well
46、 lighted and ventilated room. The color of the finished compound shall be black or brown. An oil soluble dye may be used. 3.7 Stability. The compound shall flow, be stable and uniform (see 4.6.6). The compound shall show no gelling, solidification, or more than a slight haze or precipitate. 3.7.1 Re
47、covery from low temperature. If after tilting of test tube (see 4.6.6.1), the compound flows and does not show any gelling, solidification, or more than a slight haze or precipitate, the compound meets this requirement. I it is not necessary to shake and invert test tube for a further inspection, th
48、e requirement of recovery from low temperature is met if the compound flows and does not show any lumps suggesting permanent solidification or more than a slight haze or precipitate. 3.7.1.1 Confirmatory test for recovery from low temperature. From compounds requiring shaking, the test for recovery
49、from low temperature is confirmed provided the compounds then pass the sprayability test (see 4.6.7). 3.7.2 Uniformity. The compound shall contain no precipitates formation or permanent haziness in the solution. If subsequent exposure of test panels in supernatant solution is required (see 4.6.6.1.2 and 4.6.11.4), an examination of the test panels after removal shall show not more than a trace of corrosion on the leading test surface of the panels for grades 1, 2,
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1