NAVY MIL-PRF-24667 C-2008 COATING SYSTEM NON-SKID FOR ROLL SPRAY OR SELF-ADHERING APPLICATION [Superseded NAVY MIL-D-23003A CANC NOTICE 2 NAVY MIL-D-23003A NOTICE 1 NAVY MIL-D-2300ICE.pdf

1、Comments, suggestions, or questions on this document should be addressed to: Commander, Naval Sea Systems Command, ATTN: SEA 05M2, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to CommandStandardsnavy.mil, with the subject line “Document Comment”. Since contact

2、 information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 8010 INCH-POUND MIL-PRF-24667C 22 May 2008 SUPERSEDING MIL-PRF-24667B(SH) 3 June 2005 MIL-PRF-17951E(SH) W/ AMENDMENT 2 17 September 19

3、92 (see 6.7) PERFORMANCE SPECIFICATION COATING SYSTEM, NON-SKID, FOR ROLL, SPRAY, OR SELF-ADHERING APPLICATION This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SC

4、OPE 1.1 Scope. This specification covers non-skid systems, coatings, and coverings for application to weather decks, flight decks, and hangar decks of air capable amphibious aviation and aviation ships. Coatings are applied to steel, aluminum, reinforced plastic, and special hull treatment (SHT) sur

5、faces by spraying, rolling, or other application method as designated by the manufacturer of the non-skid system. 1.2 Classification. The non-skid systems covered by this specification are of the following types and compositions as specified (see 6.2). 1.2.1 Type. The types of non-skids are as follo

6、ws: Type I High durability, rollable deck coating Type II Standard durability, rollable deck coating Type III Standard durability, rollable resilient deck coating (for use where flexibility is required and where increased weight is not a factor) Type IV Standard durability, sprayable deck coating Ty

7、pe V Extended durability, rollable deck coating Type VI High durability, fast cure, rollable deck coating Type VII Fast cure, temporary repair, rollable deck coating Type VIII Low temperature cure, rollable deck coating Type IX High temperature resistance deck coating Type X Submerged applications T

8、ype XI Peel and stick, temporary repair, self adhering deck covering Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24667C 2 1.2.2 Composition. The composition of non-skids are as follows: Composition G General use abrasive deck system (all

9、types) Composition L Limited use aircraft carrier landing and run-out area deck system that is not abrasive to the steel arresting cable (composition L applies to Types I, V, VI, VII, VIII, and IX only, and does not apply to Types II, III, IV, and X) Composition PS Self adhering, non-skid deck cover

10、ing (Type XI only) 1.3 Part or identifying number (PIN). PINs to be used for the coating systems acquired to this specification are created as follows: M 24667 - X X Prefix for Military Specification Specification Number Type (see code below) Composition (see code below) Type Code Composition Code T

11、ype Code Composition Code I A G 1 II B L 2 III C PS 3 IV D V E VI F VII G VIII H IX J X K XI L Examples: M24667-A1 M24667-J2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24667C 3 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in

12、 this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document

13、 users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a

14、 part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL STANDARDS FED-STD-141 - Paint, Varnish, Lacquer and Related Materials: Methods of Inspection, Sampling and Testing FED-STD-595/140

15、62 - Green, Gloss FED-STD-595/31136 - Red, Flat or Lusterless FED-STD-595/33538 - Yellow, Flat or Lusterless FED-STD-595/34088 - Green, Flat or Lusterless FED-STD-595/36076 - Gray, Flat or Lusterless FED-STD-595/36173 - Gray, Flat or Lusterless FED-STD-595/36270 - Gray, Flat or Lusterless FED-STD-59

16、5/37038 - Miscellaneous, Flat or Lusterless FED-STD-595/37875 - Miscellaneous, Flat or Lusterless DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-5624 - Turbine Fuel, Aviation, Grades JP-4 and JP-5 MIL-D-16791 - Detergents, General Purpose (Liquid, Nonionic) MIL-S-22698 - Steel Plate, Shapes and Bars,

17、Weldable Ordinary Strength and Higher Strength: Structural MIL-PRF-23236 - Coating Systems for Ship Structures MIL-PRF-23699 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Number O-156 MIL-F-24385 - Fire Extinguishing Agent, Aqueous Film Forming Foam (AFFF) Liquid Concentrate,

18、 for Fresh and Seawater DOD-G-24508 - Grease, High Performance, Multipurpose (Metric) MIL-PRF-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Metric, NATO Code Number H-537 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-

19、24667C 4 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1623 - Fire Performance Requirements and Approved Specifications for Interior Finish Materials and Furnishings (Naval Shipboard Use) (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil

20、 or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified her

21、ein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. CALIFORNIA CODE OF REGULATIONS Title 22, Division 4.5, Chapter 29, Article 10, 66700 - Waste Extraction Test (WET) (Copies of this document are available from Barclays West Group, P.O. Box

22、 3066, South San Francisco, CA 94083 or online at http:/ccr.oal.ca.gov/.) CODE OF FEDERAL REGULATIONS (CFR) 27 CFR21.35 - Formula No. 3A 29 CFR1910 - Occupational Safety and Health Standards 40 CFR355 Appendices A and B - The List of Extremely Hazardous Substances and their Threshold Planning Quanti

23、ties 40 CFR372.65 - Chemicals and Chemical Categories to which this Part Applies (The Code of Federal Regulations (CFR) may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20401 or online at www.gpoaccess.gov/index.html.) ENVIRONMENTAL PROTECTION AGE

24、NCY (EPA) EPA SW-846 - Test Methods for Evaluating Solid Waste, Physical/Chemical Methods EPA 600/4-79/020 - Methods for Chemical Analysis of Water and Wastes (Copies of these document are available from the Environmental Protection Agency, Ariel Rios Building, 1200 Pennsylvania Avenue, N.W., Washin

25、gton, DC 20460 or 5www.epa.gov.) NATIONAL INSTITUTE OF ENVIRONMENTAL HEALTH SCIENCES (NIEHS) National Toxicology Program (NTP) latest Annual Report on Carcinogens (Copies of this document are available from NIEHS, Public Information Office, MD B2-04, Research Triangle Park, NC 27709 or online at htt

26、p:/library.niehs.nih.gov) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24667C 5 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

27、 these documents are those cited in the solicitation or contract. AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS (ACGIH) ACGIH 0100 - Documentation of the Threshold Limit Values and Biological Exposure Indices (Application for copies should be addressed to the American Conference of Gover

28、nmental Hygienists, 1330 Kemper Meadow Drive, Cincinnati, OH 45240 or online at www.acgih.org.) AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI B74.12 - Size of Abrasive Grain-Grinding Wheels, Polishing and General Industrial Uses Copies of this document are available from the American National St

29、andards Institute, 25 W. 43rd St, 4th Floor, New York, NY 10036 or online at http:/webstore.ansi.org/. ASTM INTERNATIONAL ASTM A229/A229M - Standard Specification for Steel Wire, Oil-Tempered for Mechanical Springs (DoD adopted) ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus

30、DoD adopted) ASTM C136 - Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates (DoD adopted) ASTM D660 - Standard Test Method for Evaluating Degree of Checking of Exterior Paints (DoD adopted) ASTM D661 - Standard Test Method for Evaluating Degree of Cracking of Exterior Paints (DoD

31、 adopted) ASTM D1141 - Standard Practice for the Preparation of Substitute Ocean Water (DoD adopted) ASTM D1652 - Standard Test Methods for Epoxy Content of Epoxy Resins (DoD adopted) ASTM D2485 - Standard Test Methods for Evaluating Coatings for High Temperature Service ASTM D2572 - Standard Test M

32、ethod for Isocyanate Groups in Urethane Materials or Prepolymers (DoD adopted) ASTM D3272 - Standard Practice for Vacuum Distillation of Solvents From Solvent-Reducible Paints For Analysis (DoD adopted) ASTM D3278 - Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus

33、 (DoD adopted) ASTM D4541 - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers ASTM E260 - Standard Practice for Packed Column Gas Chromatography ASTM E1252 - Standard Practice for General Techniques for Obtaining Infrared Spectra for Qualitative Analysis Provided

34、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24667C 6 ASTM F137 - Standard Test Method for Flexibility of Resilient Flooring Materials with Cylindrical Mandrel Apparatus (DoD adopted) ASTM F718 - Standard for Shipbuilders and Marine Paints and Coa

35、tings Product/Procedure Data Sheet (DoD adopted) ASTM G8 - Standard Test Methods for Cathodic Disbonding of Pipeline Coatings ASTM G14 - Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) ASTM G154 - Standard Practice for Operating Fluorescent Light Apparatus for U

36、V Exposure of Nonmetallic Materials (Copies of these documents are available from ASTM International, 100 Barr Harbor Dr., PO Box C700, West Conshohocken, PA 19428-2959 or online at www.astm.org.) SAE INTERNATIONAL (SAE) SAE AMS1424 - Deicing/Anti-Icing Fluid, Aircraft, SAE Type 1 (DoD adopted) SAE

37、AMSC9084 - Cloth, Glass, Finished, for Resin Laminates (DoD adopted) (Copies of these documents are available from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or online at www.sae.org.) SOCIETY FOR PROTECTIVE COATINGS (SSPC) SSPC-PA 2 - Measurement of Dry Coating Thickn

38、ess with Magnetic Gages (DoD adopted) SSPC-SP 1 - Solvent Cleaning (DoD adopted) SSPC-SP 3 - Power Tool Cleaning (DoD adopted) SSPC-SP 10 - Near-White Blast Cleaning (DoD adopted) (Copies of these documents are available from SSPC Publication Sales, 40 24thStreet, 6thfloor, Pittsburgh, PA 15222-4656

39、 or online at www.sspc.org.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption ha

40、s been obtained. 3. REQUIREMENTS 3.1 Qualification. Non-skid systems furnished under this specification shall be products that are authorized by the qualifying activity for listing on the applicable qualified products list before contract award (see 4.2 and 6.3). 3.2 Materials. Each individual compo

41、nent and final combined product of the total non-skid system qualified to this specification shall, when mixed and applied in accordance with the manufacturers instructions, be in accordance with the appropriate requirements. The composition of the system furnished to this specification shall be the

42、 responsibility of the manufacturer, except as limited by this specification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-24667C 7 3.2.1 Description. 3.2.1.1 Types I-X. The total non-skid system shall consist of a non-skid topcoat, anti-c

43、orrosive primer (for metal decks only), or primer (for fiberglass decks), any needed intermediate coatings and color topping coatings. The composition of each individual coating of the non-skid system is the manufacturers responsibility subject only to the limitations of 3.2. Each individual coating

44、 of the non-skid system may be provided as one or two parts. Types I, II, III, V, VI, VII, and VIII non-skid coatings and Type III underlayment intermediate coatings shall be formulated for application by roller. Type IV coatings shall be formulated for application by spray only. The application met

45、hod for Type IX and X coatings shall be at the manufacturers discretion. 3.2.1.2 Type XI. The non-skid system shall consist of a fabric, film, or composite backing having a uniform closed coat of abrasive particles on the front surface and a pressure sensitive adhesive on the back. The abrasive part

46、icles shall be aluminum oxide, silicon carbide, or other abrasive material with a Mohs hardness of 6 or greater. When sized in accordance with the table on allowable limits for the sizing of abrasive grains in ANSI B74.12, the abrasive shall have no more than 2 percent coarser than 54 grit with none

47、 coarser than 30 grit. The abrasive shall be bonded to the backing with a resin or similar material. The adhesive on the back surface shall be of the pressure-sensitive type and shall be covered with a removable protective cover. Asbestos fibers and components containing asbestos fibers are prohibit

48、ed (see 6.3). 3.2.1.2.1 Adhesive and protective cover. The adhesive shall be pressure sensitive, coated to cover the back side of the non-skid system, and shall adhere immediately to smooth, clean, dry deck surfaces without wrinkling, curling, breaking, or lifting. A protective cover shall be used t

49、o prevent contamination of the adhesive by foreign matter until the deck treads are applied. 3.2.1.2.2 Sealing compound. The sealer is used to seal the periphery of the tread to prevent ingress of water and other liquids, especially for cotton backed treads. The compound shall be a cold-setting type ready for use and shall have no deleterious effect on the steel or aluminum deck