NAVY MIL-S-15103 F (2)-2000 SALINITY INDICATING EQUIPMENT《盐度显示设备》.pdf

1、AMSC N/A FSC 6630DISTRIBUTION STATEMENT A. Approved for public release; distribution isunlimited.1 of 2MIL-S-15103F(SH)AMENDMENT 213 July 2000SUPERSEDINGAMENDMENT 117 December 1992MILITARY SPECIFICATIONSALINITY INDICATING EQUIPMENTThis amendment forms a part of MIL-S-15103F(SH), dated 16 March 1988

2、andis approved for use by the Naval Sea Systems Command, Department of the Navyand is available for use by all Departments and Agencies of the Department ofDefense.PAGE 2* 1.2.5, Add between lines 7 and 8: “050P 0 to 50 p/m of chloride”.PAGES 3 and 42.1.1, under SPECIFICATIONS, MILITARY: Delete “MIL

3、-W-16878 - Wire,Electrical, Insulated, General Specification For and MIL-W-16878/4 - Wire,Electrical, Polytetrafluoroethylene (PTFE) Insulated, 200C, 600 Volts,Extruded Insulation.” and substitute “MIL-C-24643 - Cable and Cord,Electrical, Low Smoke, For Shipboard Use, General Specification For and M

4、IL-C-24643/2 - Cable, Electrical, 300 Volts, Types LSDCOP and LSTCOP.”PAGE 12* Table III: Add columns for 20.0 p/m and 50.0 p/m as follows:(p/m chloride (77F reference)Temp. (F)20.0 p/m 50.0 p/m40 2120 Ohms 860 Ohms75 1320 54077 1295 530100 1010 412125 805 330150 670 274175 570 233200 493 202225 435

5、 180250 390 161INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-15103F(SH)AMENDMENT 22 of 2PAGE 143.6, line 9: Delete “150 lb/in2” and substitute “250 lb/in2”* 3.6.1, line 17: After “use of thread” insert “sealing compounds”PAGE 153.6.

6、1.5: Delete and substitute:“3.6.1.5 Sensor cable. The sensor cable shall be made in accordancewith MIL-C-24643 and MIL-C-24643/2 and shall be 6 feet long. Individualconductors shall have ring tongue terminations and shall be labeled withletter designations. The outer electrode (SBB-O) lead shall be

7、red, the innerelectrode (SB-O) lead shall be white and the temperature compensator (SB-1)lead shall be black.”3.6.2, line 2: Delete “150 lb/in2” and substitute “250 lb/in2”.line 4: Delete “225 lb/in2” and substitute “375 lb/in2”.PAGE 173.8.11, line 2: Delete “225 lb/in2” and substitute “375 lb/in2”.

8、line 7: Delete “150 lb/in2” and substitute “250 lb/in2”.PAGE 274.5.15.1, line 3: Delete “225 lb/in2” and substitute “375 lb/in2”.line 4: Delete “150 lb/in2” and substitute “250 lb/in2”.line 7: Delete “225 lb/in2” and substitute “375 lb/in2”.line 12: After “shall be” insert “verified as specified in3

9、.8.11. Following the leakage test, the sensorconstant shall be”.4.5.15.2.2, line 3: Delete “225 lb/in2” and substitute “375 lb/in2”.NOTE: The margins of this amendment are marked with asterisks to indicatewhere changes from the previous amendment were made. This was done as aconvenience only and the

10、 Government assumes no liability whatsoever for anyinaccuracies in these notations. Bidders and contractors are cautioned toevaluate the requirements of this document based on the entire contentirrespective of the marginal notations and relationship to the last previousamendment.Preparing activity:Navy - SH(Project 6630-0578)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-