NAVY MIL-S-87053 C-1988 SKIRT WOMAN-S BELTED《女式束带衬衫》.pdf

1、MIL-S-87053C 8V m 7779906 04L044l 3 m MIL-S-87053C(NU) 8 August 1988 SUPERSEDING MIL-S-87053B(NU) 19 Nov 1985 MILITARY SPECIFICATION SKIRT, WOMANS, BELTED This specification is approved for use by the Navy Clothing and Textile Xesearch Facility, Department of the Navy, and is available for use by al

2、l Departments and Agencies of the Department of Defense. 1, SCOPE 1.1 Scope. This specification covers the requirements for womens skirts in fabrics and colors as specified. 1.2 Classification. The skirts shall be of one type only in the following classes, sizes, and lengths as specified in 6.2. 1.2

3、.1 Classes. Class 1 - Blue 3346 Class 2 - White 3006 1.2.1.1 Sizes. 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 18, 20, and 22 1.2.1.2 Lengths. Short, Regular, Long Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be

4、 addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8410 DISTRIBUTION STATEME

5、NT A. Approved for public release, distribution is unlimited. ,- THIS DOCUMENT CONTAINS 2 9 PAGES. y Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. Unl

6、ess otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified. SPECIFICATIONS FEDERA

7、L V-F-106 DDD-L- 20 NN-P-71 MILITARY MIL-P-15 MIL-B-17757 MIL-C-24910 MIL-T-4354a MIL-C-43718 MIL-C-87052 MIL-(2-87059 STANDARDS FEDERAL FED-STD-191 FED-STD-751 3( MILITARY MIL-STD-I05 MIL-STD-129 MIL-STD-147 MIL-STD-1609 - Fasteners, Slide, Interlocking - Label; For Clothing, Equipage, and Tentage

8、(General - Pallet, Material Handling, Wood, Stringer Use) Construction, 2 Way and 4 Way (Partial) - Pallet, Material Handling, Wood, Post Construction, - Boxes, Shipping, Fiberboard (Modular Sizes) - Cloth, Tropical; Polyester and Wool - Thread, Polyester Core; Cotton-, Rayon-, or Polyester-Covered

9、- Cloth, Polyester; Polyester and Cotton; Polyester and Rayon, for Pockets - Cloth, Twill Polyester, White - Cloth, Nylon, Tricot 4 Way Entry - Textile Test Methods - Stitches, Seams and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Uni

10、t Loads - Provisions for Evaluating Quality of Womens Skirts Attributes (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting of Eicer

11、. ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-7053C q M 7779706 04LOLt43 7 M t -i MIL-S-87053C(NU) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a

12、 part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS U.S. POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, 2.2 Other publicati

13、ons. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issue of documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of document

14、s not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. U.S. Government Printing Office, Washington, D.C. 20402.) NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for cop

15、ies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404) i UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Committee, Room 1

16、106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). * THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades for Sewing Threads Standard Shades for Thread - 1968 (Application for copies of color cards should be addressed to the Color Association of the U.S., 343

17、Lexington Avenue, New York, NY 10016). TECHNICAL MANUAL OF THE AMERICAN ASOCIATION OF CHEMISTS AND COLORISTS Method No. 135-1978 - Dimensional Changes in Automatic Home Laundering of Woven and Knit Fabrics (Application for copies should be addressed to AATCC National Headquarters, P.0, Box 12215, Re

18、search Triangle Park, NC 27709-9989.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this specification shall take p

19、recedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. iiI 3. REQUIREMENTS 3.1 Guide Sam le. Samples, when furnished, are solely for guidance and information - to t e contractor (see 6.3). Variations from this

20、 specification may appear in the sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Basic material. The basic materials for the skirts sh

21、all be as specified in 3.3.1.1 thru 3.3.1.2. wool, 10.0 - c 5 oz/yd, Shade Blue 3346, conforming to MIL-C-24910. twill, 6.7 oz per sq yd, Shade White 3006 conforming to MIL-C-87052. * 3.3.2 Lining material. The material for lining the Class 2 skirt shall be a nylon tricot warp knit, 2.7 oz per sq yd

22、 shade White 3006 conforming to 3.3.1.1 Class 1. The blue skirt fabric shall be a tropical, polyester and 3.3.1.2 Class 2. The white skirt fabric shall be a texturized polyester MIL-C-87059. * 3.3.3 Fusible interlining. The skirt waistband and pocket welts shall be fused with a woven or nonwoven the

23、rmal bonded consisting of 85-100% polyester with the remaining fiber being nylon. The material shall be free of chemical binders. The fusible adhesive system shall be a polyester paste dot uniformly distributed over one side of the material. The color shall approximate the shade oftbase fabric. The

24、total weight of the nonwoven fusible shall be 1.1 t ,2 oz/yd . The fused sample, consisting of fusible interlining and basa fabric, shall conform to the requirements stated below when tested as specified in Table III, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

25、ense from IHS-,-,-MIL-S-87053C 84 M 977790b OLlLO445 O W MIL-S-87053C(NU) Component Testing Requirements Appearance of fused samples 11 Initial 2/ - No evidence f bubbling or delamination of the bond, change of color, OF strike through. After 5 dry cleanings 2/ - No evidence of bubbling or delaminat

26、ion of the bond, change of color, or strike through. Bond strength - 31 22 oz min. - init5ally 18 OZ. after 5 launderings 18 oz - after 5 dry cleanings Shrinkage After 3 launderings - 2.5% max. After 3 dry cleanings - 2,5% max. - 1/ Applies to quality conformance and in-process tests. 2/ After evalu

27、ation for initial appearance and shrinkage, samples may be used for the remainder of appearance tests. 3/ Bhen a nonwoven fusible is used, the item will be accepted if the fusible eiTher splits from itself rather than separates from the outershell material or if it begins to separate from the outers

28、hell material higher than the minimal bond strength and then splits from itself. * 3.3.3.1 Colorfastness. All dyed, finished, fusible interlining materials shall show fastness to laundering (3 cycles) and dry cleaning (3 cycles), equal to or better than the standard sample. As a minimum level of acc

29、eptability, or when no standard sample is available the finished, dyed fusibles shall show a minimum of llfairl fastness after 3 launderings and 3 dry cleanings (see Table III). 3.3.4 Pocketing. The material for the front and back plies of the pockets shall be fabric conforming to class 1 of MIL-C-4

30、3718. The color of the pocketing for the class 1 blue skirt shall be dark grey or black and for the class 2 white skirt it shall be white. 3.3.5 Tape, waistband, non-slip. The woven non-slip tape for the waistband shall be made of polyester or a blend of- polyester/nylon natural or white in color, 1

31、/2 to 7/8 inch in width with two or three rows of nitrile or chloroprene rubber thread woven or stitched to the tape. The rows of rubber thread shall be positioned a minimum of 3/16 inch from edges of tape. The finished tape shall not shrink more than 2.0 percent in length direction when subjected t

32、o the manufacturers standard procedures for determining dimensional stability to laundering and dry cleaning, as appropriate for the end item (see 4.4.1 and 6.4). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-S-87053C 84 7797706 0410446 2 MI

33、L-S-87053C(NU) * 3.3,6 Thread. The thread used for seaming and stitching the skirts shall be a cov-polyester thread, ticket NO. 70, 2 or 3 ply conforming to MIL-T-43548. The thread for the class 1 blue skirt shall be dyed shade black AA, C.A. 66043, and shade White AH, Cable No. 66050 for the class

34、2 white skirt, in accordance with the DoD Standard Shades for Sewing Threads. The use of polyester-covered, polyester-core thread is not allowed. 3.3.6.1 Colorfastness of threads. The dyed threads shall show colorfastness to laundering, wet-dry cleaning, and light equal to or better than the standar

35、d sample when tested as specified in MIL-T-43548, As a limit of acceptability, or when no standard sample is available, the dyed threads shall show a minimum of “good“ colorfastness to laundering, wet-dry cleaning, and light when tested as specified in MIL-T-43548. 3.3.7 Labels. * 3.3.7.1 Combinatio

36、n label. Class 1 skirt shall have a combination personal/identification/instruction label conforming to type VI, classes 10 and 15 of DDD-L-20. Class 2 skirts shall have a separate personal/identification combination label conforming to Type VI, classes 1 and 10 of DDD-L-20, and a separate instructi

37、on label conforming to type VI, class 3 of DDD-L-20. The printing shall show good fastness to laundering and dry cleaning. The label shall bear the folowing inscription, and appropriate laundering instruction (separate label for class 2 skirts). 6 Provided by IHSNot for ResaleNo reproduction or netw

38、orking permitted without license from IHS-,-,-MIL-S-87053C(NU) NAME : SERVICE NO: SKIRT, WOMANS BELTED CLASS 2 (EXAMPLE) FIBER CONTENT: 100% POLYESTER (EXAMPLE) LINING: 100% NYLON (CLASS 2 SKIRT ONLY) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (if other than contractor) CONTRACT NO: DLA-100-00-0-0000

39、 NOTE: The kick pleat shall finish 6 inches in length after alterations. The following instructions apply to Class 1 skirts: MACHINE WASH - PERMANENT PRESS CYCLE IN WARM WATER (120 MAX) DO NOT BLEACH MAY ALSO BE DRY CLEANED OR TUMBLE DRY MEDIUM HEAT - REMOVE IMMEDIATELY FOLLOW NAVEDTRA MANUAL 414-01

40、-45-81 FORMULA III The following instructions apply to Class 2 skirts: FILL MACHINE WASH, PERMANENT PRESS CYCLE, HOT WASH. DO NOT MIX COLORS. MACHINE WITH CLOTHES TO 2/3 CAPACITY. USE HEAVY DUTY SOAP OR DETERGENT. PRESPOT STAINS WITH A LAUNDRY STAIN PRETREATMENT. TUMBLE DRY USING A WARM SETTING OR S

41、HAPE AND HAND DRY. REMOVE AT ONCE FROM DRYER. OR IF NEEDED USE A NON-CHLORINE BLEACH. IF TOUCH-UP IRONING IS NEEDED, USE A WARM IRON. FOLLOW NAVEDTRA MANUAL 414-01-45-81 FORMULA II 3.3.7.2 Size label. Each skirt shall have a separate size label conforming to Type VI, class 2 and shall bear the follo

42、wing inscription: SIZE: 14R (EXAMPLE) STOCK NO: 8410-00-000-0000 (EXAMPLE) The length (short, regular, or long) may be abbreviated as S, R, or Le 3.3.7.3 Removable size ticket. Each skirt shall have a commercial type size ticket attached to the outside of the waistband above the left back dart. The

43、ticket shall be 3 inches long and 1 inch high, made of a suitable plain white cardboard. The corners of the ticket may be double perforated for ease in tacking. The size (12R - Example) shall be printed or stamped on the upper left hand corner in black or blue ink. The lettering for the size shall b

44、e 1/4 inch in height. Abbreviations for lengths shall be allowed in accordance with 3.3.7.2. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-87053C 4 m 7797706 0430448 b = MIL-S-87053C(NU) 3.3.8 Hook and eye fasteners. The hook and eye for wa

45、istband shall be of the clinch type conforming to North and Judd (Hook Flex H-29 and E-40) or equal (see 6.5). The finish of both components shall be nickel plate (see 4.4.1). 3.3.9 Slide fastener. The slide fastener shall be type I, style la (continuous chain) or style 3 (pre-assembled), size LS, s

46、hort tab pull of V-F-106. The length of the style 3 slide fastener shall be 7 inches. The slide fastener chain shall be a continuous monofilament nylon or polyester coil. The color of all components shall be black for the class 1 skirt and white for class 2 skirt, or the color of the continuous coil

47、 may be clear. The complete slide fastener shall not shrink more than 2 percent when tested as specified in V-F-106. The style la (continuous chain) slide fastener requires the application of a slider and bottom stop during production of the slacks. 33.9.1 Colorfastness. The dyed slide fastener tape

48、 shall show colorfastness to laundering equal to or better than the standard sample when tested as specified in V-F-106. As a minimum level of acceptability, or when no standard sample is available, the tape shall show a minimum of rfgoodll colorfastness to laundering when tested as specified in V-F

49、-106. 3.4 Desi n. The skirt shall be unhemmed with a one panel front and two panel bdslide fastener closure at center back, two straight welt pockets on front, a hemmed kick pleat, four waist darts, a one piece non-slip waistband with five belt loops and a hook and eye waistband closure (see Figure 1). 3.4.1 Figvre, The figure is furnished for information purposes only. When inconsistencies exist between the written specification and t