NAVY MIL-S-87091 C-1988 SHIRT WOMAN-S OPEN NOTCH COLLAR《开领扼位女式衬衫》.pdf

1、6- IPI - 10 MIL-S-87091C(NU) 14 September 1988 SUPERSEDING MIL-S-87091B(NU) 13 December 1986 MILITARY SPECIFICATION SHIRT, WOMANS, OPEN NOTCH COLLAR y This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all De

2、partments and Agencies of the Department of Defense. IL - distribution is unlimited. -. THIS DOCUMENT CONTAINS 35 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-87OgIC( NU) SPECIFICATIONS FEDERAL V-B-871 NN-P-71 DDD-L-20 MILITARY MIL-P-

3、15011 MIL-B-17757 MIL-C-21881 MIL-T-43548 MIL-C-43594 MIL-P-55010 MIL-C-87052 STANDARDS FEDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 Button, Sewing Hole and Button, Staple, (Plastic) Pallet, Material Handling, Wood, Stringer Label; for Clothing, Equipage and Tentage (General Cons

4、truction, 2 Way and 4 Way (Partial). Use ) l6 Pallet, Material Handling, Wood, Post Construction, 4 Way Entry Boxes, Shipping, Fiberboard (Modular Sizes) Cloth, Poplin, Polyester and Cotton Thread, Polyester Core: Cotton-, Rayon-, or Cloth, Interlining, Polyester Plastic, Sheet, Polyethylene Terepht

5、halate Cloth, Twill, Polyester, White Polyester-Covered ” stitches per buttonhole less than minimum specified Finished cut length not as specified Uncut or partially cut buttonhole BT“ - One or more Missing, broken, defective, misplaced, not positioned or attached as specified, or insecurely sewn No

6、t specified type, size, or color Stitching on one or more not locked at end of cycle (tug at the loose end of the thread when accessible to determine if it will ravel) Stitching not caught through all plies COLLAR Any pleat, pucker, or crease 1. n topcollar piece 2. n undercollar piece Length betwee

7、n collar points uneven by: 1. 2. 3. More than 3/8 inch More than 1/16 inch up to and including 1/4 inch Elore than 1/4 inch up to and including 3/8 inch Twisted, not smooth, too full, short, or tight causing collar to turn out Edge of collar not properly forced out, i.e., having a fold of: 1. 1/16 i

8、nch up to and including 1/8 inch in depth 2. More than 1/8 inch in depth One or both collar stays missing One or both collar stays misplaced Edge of undercollar exposed beyond edge of topcollar: 1. 1/16 inch or more for a distance of 2 inches 2. or more Less than 1/16 inch on major portion of collar

9、 AB X X X X X X X X X X X X X X X X X X X X 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-8707LC 4 9 7777706 0432044 4 9 Classification Defect Major Minor AB h. Width of collar at center back less than 2-5/8 inches or more than 2-7/8 inch

10、es X i. Collar points measure less than 3 1/8 inches or more then 3 3/8 inches X j. Any evidence of the collar stay or reinforcement material protruding into the fold of the finished topcollar. X XI POCKETS OR FLAPS a. Pocket not uniform in size or shape - any measurement varying from pocket to pock

11、et or pocket to template by: 1. 2. More than 3/8 inch 1/4 inch up to and including 3/8 inch b. Flap not uniform in size or shape - any measurement varying from flap to flap or flap to template by: 1. 2, More than 3/8 inch 1/4 inch up to and including 3/8 inch c. Out of alignment at any point from po

12、cket to pocket or flap to flap by: (Determination may be made by a straight edge) X X X X 1. 1/4 inch up to and including 3/8 inch X 2. More than 3/8 inch up to and including 1/2 inch 3. More than 1/2 inch X X d. Pocket or flap not according to template on any side by: 1. More than 1/8 inch up to an

13、d including 3/16 2. 1/4 inch or more inch X e. Unbalanced positioning between pockets to center front (measurement taken from side edge of pocket to center of buttonhole). X 1. 1/4 inch up to and including 3/8 inch 2, More than 3/8 inch up to and including 1/2 inch 3. More than 1/2 inch X X X a 26 P

14、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Q - Defect Ma j or Mi nor AB a. Pocket edge(s) not parallel to front edge of shirt by: 1. 3/16 inch up to and including 1/4 inch X 2. 3. More than 3/8 inch More than 1/4 inch up to and including 3/8 inch

15、 X X n b. Edge of pocket pleated, puckered or twisted c. Width of pocket less than 4-3/8 inches or more than 4-5/8 inches d. Depth at center of pocket less than 4-5/8 inches or more than 4-7/8 inches e. Depth at sides of pocket less than 4-1/8 inches or more than 4-3/8 inches f. Pocket hem not overe

16、dged g. Pocket not according to template on any side by: 1. 2. 1/4 inch or more More than 1/8 inch up to and including 3/16 inch. XII1 FLAP(S) a. b. c. d. e. Width of pocket flap less than 4-1/4 inches or more than 4-1/2 inches Depth of pocket flap at center less than 1-7/8 inches or more than 2-1/8

17、 inches Depth of pocket flap at sides less than 1-1/4 inches or more than 1-1/2 inches. Pocket exposed beyond end of flap by 1/8 inch or more w/flap unbuttoned Fabric threads visible after attachment of flap a XIV FRONTS a. b. Any button out of alignment with corresponding buttonhole, causing a noti

18、ceable bulge Lengths of fronts uneven at bottom when buttoned: 1. 2. More than 3/4 inch 3/8 inch up to 3/4 inch inclusive XV ARMHOLE AND SLEEVE a. Setting: 1. Sleeve tight at armhole, causing pleats or excessive puckers on front, back, or sleeve X X X E X X X X X X X X X X X X 27 Provided by IHSNot

19、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-8709LC 4 999990b 0432046 B Classification Defect Ma j or Mi nor AB 2. Sleeves reversed, i.e., left sleeve in right armhole; right sleeve in left armhole 3. End of side and underarm seams not staggered as specified.

20、XVI SLEEVE HEZ4 a. Hem twisted, pleated, or puckered b. width not as specified c. Irregular in width by 1/4 inch or more XVII LABEL OR MING a. b. Missing, incorrect, illegible, or strike through Not attached or affixed as specified, misplaced, or stitching through the printing XVIII SHOULDER EPAULET

21、S a. b. c, Not positioned as specified or attached crookedly Not smooth and flat along the shoulder area, affecting appearance Width of finished epaulet less than 1-3/8 or more than 1-5/8 at end of buttonhole furthest from pointed edge Width of finished epaulet less than 1-5/8 inches or more than 1-

22、7/8 inches at armhole seam Epaulet tight, loose or badly distorted when buttoned Back (squared) end of epaulet center positioned less than 3/16 inch or more than 5/16 inch beyond shoulder seam d. e. f. XIX EARTACK OR TACK - One or more a. Missing, insecure, misplaced, not specified size or type, or

23、not serving intended purpose: 1. Bartack for attachment 2. Bartack for reinforcement X X X X X X X X x, X X X X b. Loose stitch tension X 28 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.5.2. Dimensional examination. The shirt shall be examined f

24、or defects in dimensions in accordance with th e following: a. Any measurement deviating from the dimensions and tolerances specified in Table II shall be scored as a size measurement defect. b. Sleeves uneven in length by 1/2 inch or more shall be scored as a size measurement defect. 4.5.2.1 Inspec

25、tion levels and acceptable quality levels (AQLs). The inspection levels and acceptable quality levels, expressed in defects per 100 units for visual and dimensional examination, shall be as follows: AQL Inspection level e For defects applicable to 4.5.1 Major Major and minor A Major, Minor A and Min

26、or B (combined) For defects applicable to 4.5.2 One class III 1.5 6.5 15.0 4.0 s-3 4.6 Examination of packaging requirements. An examination shall be made to determine that packaging, packing and marking comply with the section 5 requirements of this specification. The sample unit shall be one shipp

27、ing container fully prepared for delivery. Examination for closure defects listed below shall be made. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the AQL shall be 2.5 defects per 100 units. e 4.5 Examination of packag

28、ing requirements. An examination shall be made to determine that packaging, packing and marking complies with Section 5 requirements of this specification; Defects shall b scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery. Defects o

29、f closure listed below shall be examined on shipping containers fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the AQL shall be 2.5 defects per hundred units. I 29 Provided by IHSNot for Resal

30、eNo reproduction or networking permitted without license from IHS-,-,-RIL-S-8709LC 84 W 9999906 0432048 L W Examine Defects Marking (interior Wtted, incorrect, illegible, of improper size, location, sequence, or method of application. and exterior) Material Any component missing, damaged or not as s

31、pecified. Workmanship inadequate application of components, such as: incomplete closure of container flaps, improper taping, loose strapping, inadequate stapling. Distorted or bulging containers. Content pen and non-continuous heat sealed seams and Aiternate closure of polyethylene bag not provided

32、Omission of required vent ho& in polyethylene bag. er of shirts per shipping container more or Size shown on one or mre items not as specified on closure of polyethylene bag. l/ with tuck or reverse flap. 1/ 1/ less than specified. 1/ shipping container. - 2/ l/ For this defect, one container in the

33、 sample shall be examined. - z/ For this defect, one item from each shipping container in sample shall be examined. 4-7 Palletization examination. An examination shall be made to determine that the palletization complies with the section 5 requirements, Defects shall be scored in accordance with the

34、 list below. The sample unit shall be one palletized unit load fully packaged. The lot size shall be the number of palletized unit loads in the end item inspection lot. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5 in accordance with MIL

35、-STD-105. Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirements. Palletization Weight Marking Pallet pattern not as specified. Interlocking of loads not as specified. Load not bonded with required straps as specified. Exceeds maxim load limits. Omitted, incorrect, illegible, of improper size, location, sequence, or method of application. 30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-