NAVY MIL-STD-001303 C-1994 PAINTING OF NAVAL ORDNANCE EQUIPMENT《海军军械设备喷漆》.pdf

1、_,NOTE: The cover page of this standard has beenchanged for administrativereasons.There areno otherchanges to this document.MIL-STD-O01303C(OS)11 APRIL 1994USED IN LIEU OFMIL-STD-1303B15 APRIL 1975DEPARTMENT OF DEFENSESTANDARD PRACTICEPAINTING OFNAVAL ORDNANCE EQUIPMENTAREA MISCProvided by IHSNot fo

2、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-ST1M01:303 C(OS)FORWARD1. This military standard has been prepared by the Naval Sea Systems Command based uponcurrently available technical information but it has not been approved for promulgation as a coordinatedrevis

3、ion of MIL-STD-1303. It is subject to modification. However, pending its promulgation as acoordinated military standard, it may be used.2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which maybe of use in improving this document should be addressed to: Commande

4、r, Indian Head Division, NavalSurface Warfare Center, Standardization Branch (Code 8420), 101 Strauss Avenue, Indian Head, MD 20640-5035 by using the StandardizationDocument Improvement Proposal (DD Form 1426) appearingat the end of this document, or sending a letter.“,:iiProvided by IHSNot for Resa

5、leNo reproduction or networking permitted without license from IHS-,-,-MIL-STD401303C(OS)CONTENTSParagraphI. SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1l.l Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6、 . . . . . . . . . . . . . . . . . . 12. APPLICABLEDOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.1 Governmentdocuments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.1.1 Specifications andstandards. . . . . . . . . . .

7、 . . . . . . . . . . . . . . . . . . . . . . . . . . 22.20rder ofprecedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.1 paint systems . . .

8、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.2 Re Warheads, Guided MissileCoating, Epoxy, VOC - CompliantTape, Pressure-Sensitive Adhesive for Dissimilar Metal SeparationGrease, Aircraft and Instrument, Gear and Actuator Screw, NATOCode Number G-354,

9、MetricInsulating Varnishes and Solventless Resins for Application by theDip ProcessCement, Epoxy, Metal Repair and Hull SmoothingInsulation Tape, Electrical, Plastic, Pressure-Sensitive3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-., .,. MIL-STD4X

10、11303C(OS)MIL-P-24441MIL-P-24441/lML-P-2444116DOD-E-24607MIL-E-24635MIL-P-24647DOD-P-24648MIL-P-53030ML-G-81322MIL-C-85285STANDARDSFEDERALFED-STD-141FED-STD-595MxLrTARYMS603MIL-STD-709MIL-STD-889Paint, Epoxy-Polyamide, General Specification ForPaint, Epoxy-Polyamide, Green Primer, Formula 150, Type

11、IPaint, Epoxy-Polyamide, Exterior Topcoat, Dark Gray, Formula155-RO = 6, Type IEnamel, Interior, Nonflaming (Dry), Chlorinated A1kyd Resin,Semigloss (MetJic)Enamel, Silicone Alkyd CopolymerPaint System, .Anticorrosive and Antifouling, Ship HullPrimer Coating, Zinc Dust Pigmented for Exterior Steel S

12、urfacesPrimer Coating, Epoxy, Water Reducible, Lead and ChromateFreeGrease, Aircraft, GeneraI Purpose, Wide Temperature RangeCoating: Polyurethane, High-SolidsPaint, Varnish, Lacquer and Related Materials: Methods ofInspection, Sampling and TestingColors Used in Government ProcurementFormula for Fuz

13、e Thread Luting (For Special Ammunition Use)Ammunition Color CodingDissimilar Metals(Unless otherwise indicated, copies of Federal and military specifications, and standards are availablefrom: Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Phdadelphia, PA 19111-5094.),. 2.2 Orde

14、r of precedence. In the even of conflict between the text of this document and the,4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-O01303C(OS)references cited herein, the text of this document takes precedence. Nothing in this documen howeve

15、r,supersedes applicable laws and regulations unless a specific exemption has been obtained.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-h41L-sTDamo3c(os)3. DEFINITIONS3.1 Paint systems. Paint systems are the series of coatings applied over properl

16、y cleaned andchemically treated or otherwise pretreated surfaces. A paint system will include the following, in theorder of application:a. Type of primer and number of coats each, in the order of application to the surfaces includingany fillers, surfacers, or sealers required.b. Type of finish coats

17、 (paints, enamels, varnishes, or others) and number of coats each, in theorder of application over the primer.c. TJiclums of individual coats or of the entire system and other pertinent information is includedwhere necessary.3.2 Resins. Resins are solid organic substances, either natural, originatin

18、g in the secretion of certainplants and insects, or synthetic. They are thermoplastic, flammable, nonconductive of electricity, breakwith a conchoidal fracture (when hard), and dissolve in certain specific organic solvents other than water.3.3 Drying oils. Drying oils, as used in paint compositions,

19、 possess (to a marked degree) theproperty of readily takimg up oxygen from the air and changing to a relatively hard, tough elasticsubstance when exposed in a thin fdm in air.3.4 Mgments. Pigments are fine solid particles that impart hiding and color to paint and aresubstantially insoluble in the ve

20、hicle.3.5 Primers. Primers are the first coat of a paint system. They are applied to suitably preparedwood, or to chemically or electrochemically treated metal. They improve adhesion of the subsequent paintcoats and aid in protecting the metal against corrosion.3.6 FNlera. Fillers are pigmented comp

21、ositions for filling pores or irregularities in a surfacepreparatory to application of other finishes.3.7 Surfacers. Surfacers are pigmented compositions for filling minor irregularities to obtain asmooth uniform surface preparatory to applying finish coats. They are usually applied over a primer an

22、dsanded for smoothness.3.8 Sealers. Sealers are liquid compositions that prevent excess absorption of fudsh coats intoporous surfaces and can also be used to prevent bledng.3.9 Paints. Paints are pigmented liquid compositions that are converted to an opaque solid film afterapplication as a thin laye

23、r.3.10 Enamels. Enamels are paints characterized by their ability to form an especially smooth film.3.11 Varnishes. Varnishes are solutions of resins and drying oils, or resins alone in solvents. Upon6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

24、IL-STD-001303C(OS)drying, they form a clear to dark amber film. Varnishes may be mixed with stains to approximatelyduplicate wood finishes. Varnishes that contain a large amount of opaque pigments are usually listed asenamels.3.12 Other terms. Other general terms, frequently encountered in the speci

25、fications of paints,varnishea, and related materials may be found in Section 8 of FED-STD-141.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-001303C(OS)4. GENEIWL REQUIREMEIWS4.1 Use of th standard. This standard shall be used as a general g

26、uide to the selection of paintingmatcirials, systems, procedures, and their designation or identification on drawings or other documentsapplicable to naval ordnance equipment and weapons. For general procedures, such as preparation forpainting, reference may be made to the standard as a whole. Howev

27、er, specific reference shall be made,in accordance with the descriptions or designations herein, when particular materials, processes, or paintsystems are to be used. System number and alternates, if any, must be specified when this standard isused to define a protective finish on a hardware item.4.

28、2 Use of specification materials and processes. Unless otherwise spifkd in the procurementdocuments, materials, and processes used in painting of naval ordnance equipment shall be in accordancewith the latest issues of the applicable specifications listed herein. The film thickness of paint typemate

29、rials and techniques of the application shall be .as specified in ML-F-18264. Other Federal andmilitary specifications may be used when prior approval is obtained from the Naval Sea SystemsCommand. Company standards, industry specifications and industry practices shall be subject to priorapproval by

30、 the Naval Sea Systems Command before use.4.3 Surfaces requiring painting. Practically all metal and wood surfaces exposed to weather arepainted for protection against deterioration. Surfaces of some metals, such as corrosion-resisting steel,copper alloys, and cerin aluminum containers may be left u

31、npainted if they are enclosed or otherwisesufficiently protected against moisture, high humidity, or salt spray. Aluminum containers, wheredetermined necessary, may be coated with primer conforming to MIL-P-24441.4.4 Surfaces not to be painted. Certain types of surfaces do not require painting or ar

32、e harmfdlyaffected by painting. These include the following:a.b.c.d.e.f.Machined surfaces that are required to move against or assemble to others such as threads,slides, bearing contacts, gear teeth, bourrelets, rotating bands, and linkages. Moving parts aregenerally lubricated when in use.Electrica

33、l parts and components already assembled, such as contact supports, relays, sockets,plugs, connectors, and insulators. When any portion of these are to be painted, it shall be doneprior to assembly. If touchup is required, as on cut or machined plastics, utmost care shall beused to avoid leaving any

34、 paint residue on electrical contact surfaces, hinges, pivots, bearingsurfaces, or others whose proper operation may be affected by such residues.Parts of copper or copper alloys, plated or unplated, such as ekctrical sockets, plugs,comectors, contacts, and terminals.Plastic, rubber, or ceramic insu

35、lators, mounts, spacers, gaskexterior of miseilee wherespecified.14 Enamal, gloss TT-P-645 MIL-E-24635 2 Metal surfaces notwhite white No. 17875 exposed to waather, forhigh light reflection. ., .,10Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

36、STD4101303C(OS)TABLE I. Naval Sea Systems Command standard paint systems - Continued.System Name and Primer. Paint and No.No. Co!or Filler, Color No. of usesSurfacer F5D-STD-595 Costa14C Paint, Interior ?T-P-645 DOD-E-24607 1 Metal interior eurfaceswhite, fire not exposad to waather,ratardant for hi

37、gh light reflectionand firs ratarding20 Coating system for MIL-P-24441 /1 MIL-E-24635, 4 coats total, Extarior surfaces oftopside combat (1 coat, 3 to 4 color No. 26270 (2 7 to 10 roils above deck radar andayatema, roils) and then coats, 1 to 1.5 total optical equipment,equipment, haze MIL-P-24441 J

38、6 roils each coat) thicknaas axcluding reflactivagray (1 coat. 2 to 3 surfacas of radomes, Mkroils) 86 Remota Optical Sight,AN/SPQ-9, AN/SPG-60,AN fsPa-9B20A Coating system for MIL-P-24441 /1 Sprayiat 599- 8 coats total Reflective surfaces,reflective surfaces, (1 coat) Y1 002 or ANISPG-60haza gray e

39、quivalent (see6.4) copperconductive paint (3coats),MIL-P-24441 /1 (1coat), and thenMIL-E-24635,color No. 26270 (2coats)20B Coating syatam for MIL-P-24441/l MIL-E-24635, 3 coats total, Exteriorsurfacaofradomas, haza (1 coat, 0.5 to color No. 26270 2 2.5 to 4 milS radomes, AN/SPQ-9gray 1 roil) coats,

40、1 to 1.5 totalroils each coat) thickness22 Paint, haza gray lT-P-645 MIL-E-24635 COIOr 2 Extarior of gun barrels,(for metal) No. 26270 mounts, launchers, dapthcharges, and projectors;casea for torpado tastaquipment etc.25 Paint, aluminum TT-P-645 TT-P-28 2 Metal casaa armoradcable, ammunition andcar

41、tridge boxes andtanks: exteriors of gunbarrels, mounts,Iaunchad dapth chargas,and projectors.31 Varnish (for wood) TT-F-336 filler MIL-C-85285 Type 2 Natural wood finish, a.g.,II (Approved for for hard wood boxes, anduse on wood casessurfaces end topcoat only.), orTT-v-l1911Provided by IHSNot for Re

42、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD4101303C(OS)TABLE I. Naval Sea Systems Cbmmand standard paint systems - Continued.Primer, Peint and No.;yatem Name andNo. Color Filler, color No. of UaaeSurfacer FED-STD-595 Coate37 Enamel, eemigloss TT-P-645 MIL-E-24635

43、 cless 2 Equipment inside ehields,light gray II color, light grey turrets or elactricelNo. 26307 panels end enclosures;cables, end enclosed firecontrol equipment42 Varnish, electrical None MIL-I-24092 1 Sealing, touchup, orinsulating moisture-proofing ofelectrical parts247 Coating None MIL-C-450, so

44、lvent 1 Surfeces of cevities incompound, type, or contact with explosives;acidproof, cavity MIL-C-3301 acid rasistant coatinglining hotmek46 Paint, anti-fouling MIL-P-24441 MlL-P-l 5931, Or 2 or more to Exterior eurfaces ofred MIL-P-24647 4 roils moored minas, andminimum floate; stenciling onthickne

45、ss moored mines (2)48A Enamel exterior MIL-P-24441 MIL-E-24635 color 1 or more to Marking, Iettaring onwhite No. 27875 4 roils minceminimumthickness49 Paint, vinyl alkyd, MIL-P-24441 MIL-E-24635 color to 4 mile floats, buoye, and harborgray No. 26118 minimum defanse items (2)thickness51 Paint, fluor

46、escent lT-P-645 MIL-E-24635, 1 each (MiL-L- Torpedo exercise head,orenge MlL-L-2I891 Type 3891 not for visibility; forF, liquid form more than 3 underwater objactsorange color. roils) (clhmce sighting)TopcoatMIL-C-85285, notmore than 1 roil.52 Enamel, semigloss TT-P-645 MIL-E-24635 Type 2 coate gree

47、n Exterior surfaces ofgreen (1 coat) II green No. 24109 aluminum torpedoee;1 coat white metal surfaces ofWhite INo. 27875 ammunition andammunition containersAlternate greenand white withfinal coat giean53 Paint vinyl alkyd TT-P-645 MIL-E-24635 color 1 Torpedoesgrey No, 2611854 Coatings for color TT-

48、P-645 MIL-E-24635, 1 Color coding of weaponscoding and color as applicable and ammunitionmarking components inaccordance withMIL-STD-709, andIettaring and stencilinformation/12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-O01303C(OS)TABLE I

49、. Naval Sea Systems Chunand standard paint systems - Continued.System Name and Primar. Paint and No.No. Color Filler, Color No. of UaaoSurfacer FED-STD-595 Costa58 Enamel, quick lT-P-645 MIL-E-24635 color 1 Exterior of anchordrying Iuateriess as epecified housing; parta of minceyellow, black,brown, and blue60 Enemel, eemigloss TT-P-645 MIL-E-24635 blue, 1 Metal surfaca