NAVY MIL-STD-1320-12 A-1991 TRUCKLOADING TORPEDO MK 44 AND MK 46 ASSEMBLIES IN CONTAINER MK 197 MOD 1《MK 44和 MK 46鱼雷组件在MK 197 MOD 1集装箱的装车》.pdf

1、NIL-STD-3320 -32A 83 I 9779733 0303750 4 A REV LTR M I LI TARY STANDARD MIL-STD-1320-12A CONTAINERLOADING AND CAALDADING MILITARY TOA SYSCOM STANDARDS, REFER TO INDEX TO STANDARDS, REVISION DESCRIPTION DATE MIL.-HJBK-236 INAVYI. APPROVAL TRU CK L O AD I N G NAVY) 21 MAY 1991 TORPEDO MK 44 AND MK 46

2、ASSEMBLIES SUPE RSE DIN G 3 JANUARY i975 IN CONTAINER MK 197 MOD 1 M IL -STD- 1320- 12 CONTAINER DATA UNIT LOAD DOCUMENT . MIL-STD-1323-241 um LOAD . MK 197 MOD 1 . CON“ERS DIMENSIONS 114 L X 20 W X 22 H GROSS WEIGHT . 642-810 LES A CUBE . 29.0 CU FT A DO NOT USE FOR SHIPPING WEIGHT FOR HAZARD CLACC

3、IFICATION,CEE NAVCEA OP 2165. u!ux PAGE GENERAL NOTES. 2 FTL TRAILER . 3 6 4 LTL TRAILER . 5 . 7 UNITIZING PROCEDURES 8 AMSC NO. - N/A DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC RELEASE : DISTRIBUTION IS UNLIMITED. NOTES: AUTHORIZED AND RELEASED FOR HIGHWAY SHIPMENT ONLY. n f TOA, WPNSTA EARLE DAT

4、E 5/23/9 CIGHATURE CEASYSCDM BY DIRECTIOH DATE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -12A 81 = 9999911 0103751 b MIL-STD-1320-12A (NAVY1 GENERAL NOTES I. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR TRUCKLOADING LOADED CONTAIN

5、ERS ANO UNIT LOADS OF MK 44 ANO MK 46 TORPEDO ASSEMBLIES IN THE MK 197 MOD I CONTAINER. THE PROCEDURES DESCRIBED HEREIN ARE INTENDED FOR 45 FT THROUGH 48 FT FLATBED TRAILERS WITH THE TRAILERS TANDEM AXLES LOCATE0 IN ANY POSITION. 00 NOT USE TRAILERS WITH METAL FLOORS. CHAINS AND STEEL STRAPPING MAY

6、BE USEO INTERCHANGEABLY ON A ONE TO ONE BASIS FOR TIE DOWNS. STEEL STRAPPING USEO AS TIE DOWNS SHALL BE 2 X .O50 AND SHALL CONFORM TO AND BE APPLIED AS SPECIFIED IN THE GENERAL TRUCKLOADING DOCUMENT. MIL-STO-I320 (NAVY). CHAINS, FITTINGS ANO LOAO BINDERS SHALL CONFORM TO ANO BE APPLIED AS SPECIFIED

7、IN THE GENERAL TRUCKLOADING DOCUMENT. MIL-STO-I320 (NAVY) EXCEPT THAT THE CHAIN/GRAB HOOKS SHALL BE ATTACHED TO THE STAKE POCKETS (NOT AROUND THE RUB RAIL). PROTECTOR BOARDS (DOUBLED 2 X 6s) SHALL BE USEO UNDER THE TIE DOWNS. WHEN USING STEEL STRAPPING, THE STRAPS SHALL BE STAPLE0 TO THE PROTECTOR B

8、OARO USING 2 INtH STRAPPING STAPLES. WHEN USING CHAIN, THE CHAINS SHALL BE SECURED TO THE PROTECTOR BOARO BY DRIVING A Iod NAIL THROUGH THE CHAIN LINK ANO CLINCHING THE NAIL OVER THE CHAIN. FIVE STAPLES/NAILS SHALL BE USEO FOR EACH TIE DOWN. PRIOR TO LOADING THE TRAILER ANO DURING PRELOADING INSPECT

9、ION, REQUIRED BY NAVSEA OP 2165 ANO REPORTED ON DD FORM 626. THE CHAINS. FITTINGS AND LOAO BINDERS SHALL BE INSPECTED FOR STRETCH, GOUGING, BENT LINKS, WEAR ANO ANY OTHER NOTICEABLE DEFECTS. THE INSPECTOR SHALL CONFIRM THAT THE CHAINS. FITTINGS AND LOAO BINDERS HAVE BEEN INSPECTED AND SHALL SO NOTE

10、IN ITEM NO. 22 OF DD FORM 626. ANY DEFICIENCY SHALL BE CAUSE FOR REJECTION OF A CHAIN OR LOAO BINDER. UNLESS OTHERWISE SPECIFIED. DUNNAGE LUMBER. STEEL STRAPPING. STRAP SEALS AND NAILS SHALL BE AS SPECIFIED IN THE GENERAL TRUCKLOADING DOCUMENT, MIL-STO-I320 (NAVY). THE MAXIMUM GROSS WEIGHT OF THE TR

11、ACTOR-TRAILER ANO THE ALLOWABLE AXLE WEIGHTS ARE THE RESPONSIBILITY OF THE CARRIER. THE CARRIER WILL ADVISE THE SHIPPER OF THESE LIMITATIONS ANO THE SHIPPER SHALL LOAD THE TRAILER IN SUCH A MANNER THAT THE TRACTOR-TRAILER WILL NOT EXCEED THESE LIMITATIONS. AFTER THE BLOCKING. BRACING ANO TIE DOWNS H

12、AVE BEEN INSPECTED, THE CONTAINERS SHALL BE COMPLETELY COVERED WITH FIRE RESISTANT WATERPROOF TARPAULINS. THE TARPAULINS MAY BE UNDER THE TIE DOWNS. AFTER THE TARPAULINS ARE IN PLACE, ATTACH PLACARDS AS REQUIRED TO BOTH SIDES, FRONT, AND BACK OF THE TRAILER AND ATTACH THE SHIPPING DOCUMENTS TO AN AC

13、CESSABLE AREA ON THE BACK DECK OF THE TRAILER. FOR GENERAL TRUCKLOADING PROCEDURES REFER TO THE GENERAL TRUCKLOAOING DOCUMENT. MIL-STD-1320 (NAVY). 2. 3. 4. 5. 6. 7. 8. 9. IO. I I. 12. 2 X 6 TRIPLED. NAIL IST PECE TO TRAILER FLOOR WITH 16d NAILS EVERY 6-8 INCHES. NAIL 2ND PIECE TO 1ST AND 3RD TO 2ND

14、 IN LIKE MANNER. P 2 X 6 TRIPLED. NAIL IST PECE TO TRAILER FLOOR WITH 7-16d NAILS. NAIL 2ND PIECE TO 1ST AND 3RD TO 2ND IN LIKE MANNER. o DETAIL 0 PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L320 -32A 81 I 9999933 0303752 8 mz FTL

15、45 FT THROUGH 48 FT TRAILE (45 FT TRAILER SHOWN) e NOTEI .- I SEE DETATL A NUMBER OF CONTAINERS . WEIGHT . . . . . . . . 30816-38880 LES A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3320 -32A 83 I 9999733 0303753 T S MIL-STD-1320-12A (NA

16、VY1 , FTL 40 FT THROUGH 44 FT TRAILER (FLATBED) (40 FT TRAILER SHOWN) 9 TARPAULI NS OVER CONTAI NERS OM1 TTED FOR CLARITY. I l NAIL PIECE 1 TO TRAILER NAIL PIECE 3 TO TRAILER FLOOR W/I-IW NAIL FLOOR W/I-lW NAIL EMRY 8 INCHES. NAIL EVERY 6 INCHES, NAIL PIECE 2 TO PIECE 1 W/I-ltd PIECE 4 TO PIECE 3 W/

17、I-l6d NAIL EVERY 8 INCHES. NAIL EVERY 6 INCHES. TRUCKLOAD DATA NUMBER OF CONTAINERS WEIGHT . . . . . , . . . . 30816-38880 LBS A . . . . . . . . . 48 A DO NOT USE FOR SHIPPING WEIGHT PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3320

18、 -32A 1 S 99999L3 0303754 L E- M l L- ST- 1320- 12A (NAVY) LTL 40 FT THROUGH 48 FT TRAILERS (FLATBED1 I. WHEN REPUIRED TO SHIP LESS-THAN-TRUCKLOAD, SELECT THE CORRECT LOAD PATTERN, FOR THE NUMBER OF UNIT LOADS TO BE SHIPPED, FROM TABLE I. POSITION UNIT LOADS ON THE TRAILER AS SHOWN IN TABLE I. BLOCK

19、 AND TIE DOWN USING THE PRIN PAGES 6 AND 7 AND THE GENERAL DOCUMENT MIL-STO-1320- (NAVY). THE BLOCKING ON PAGE 6 SHOWS THE INTERFACE BETWEEN STACKS OF ONE AND TWO UNIT LOADS. WHEN LOADING AN ODD NUMBER OF CONTAINERS OR FOR SHIPPING 42 OR 46 CONTAINERS, REPLACE A CONTAINER WITH THE FILLER ASSEMBLY SH

20、OWN ON PAGE 7 AND INDICATED BY A ASTERISK BELOW. 2. 3. 4. NO. OF CNTRS 48 46 44 42 40 38 36 34 32 30 28 26 24 NO. OF CNTRS 22 20 18 I6 TABLE. I LOAD PATTERN * mmm - - - . 14 12 IO I I B I kzkl r PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

21、MIL-STD-1320-12A NAVY) 2 X 4 X 18 DOUBLED. NAIL IST PIECE TO TRAILER FTOOR WITH 6-16d NAILS NAIL 2ND IECE TO IST IN LIKE MANNER. 2 X 6 X 48 PIPLED. NAIL 1ST PIECE TO TRAILER FLOOR WITH 16d NAILS EVERY 6-8 INCHES. NAIL 2ND PIECE TO IST AND 3RD TO 2ND IN LIKE MANNER. 2 X 6 X 18 TRIPLED. NAIL IST PIECE

22、 TO TRAILER FLOOR WITH 7-16d NAILS. NAIL 2ND PIECE TO IST AND 3RD TO 2ND IN LIKE ;MANNER. BLOCKING REQUIRED WHERE 2 UNiT LOADS MEET i UNIT LOAD 2X4X18; n IST PIECE 2ND IN LIKE MANNER. BLOCKING REQUIRED WHERE 2 UNIT LOADS MEET 1 CONTAINER. 2 X 4 X 18 DOUBLED. NAIL 2 X 6 X 24 TRIPLED. NAIL IST PIECE T

23、O TRAILER FLOOR WiTH 16d NAILS EVERY 6-il INCHES. NAIL 2ND PIECE TO 1ST AND RD TO ND IN LIKE MANNER. IST PIECE TO TRAILER FLOOR WITH 6-16d NAILS. NAIL 2ND PIECE TO IST IN LIKE MANNER. 2 X 6 X 48 TRIPLED. NAIL IST PIECE TO TRAILER FLOOR WITH 16d NAILS EVERY 6-8 INCHES. NAIL 2ND PIECE TO IST AND 3RD T

24、O 2ND IN LIKE MANNER. 2 X 6 X 18 TRIPLED. NAIL IST PIECE TO TRAILER FLOOR WITH 7o16d NAILS. NAIL 2ND PIECE TO 1ST AND 3RD TO 2ND IN LIKE MANNER. PAGE 6 BLOCKING REQUIRED WHERE 1 UNIT MAD MEETS 1 CONTAINER. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

25、,-,-MIL-STD-L320 -32A L E 9799933 O303756 5 E MI L- STD- 1320- 12A FILLER ASSEMBLY INSTRUCTIONS I. END NAIL LONGITUDINAL BOARD, ITEM I, TO LATERAL BOARD, ITEM 3, WITH 2-Iod NAILS. 2. END NAIL LONGITUDINAL BOARD, ITEM I, TO HORIZONTAL SPACER, ITEM 5, 3. END NAIL HORIZONTAL SPACER. ITEM 5, TO VERTICAL

26、 SPACER, ITEM 4. WITH 2-Iod NAILS. WITH 2-Iod NAILS. 4. NAIL LONGITUDINAL BOARD, ITEM I, TO VERTICAL SPACER, ITEM 4, WITH 2-Iod NAILS. 5. NAIL LONGITUDINAL BOARD, ITEM I, TO VERTICAL BOARD, ITEM 2, WITH 6. SIDE NAIL LATERAL BOARD. ITEM 3, TO VERTICAL BOARD, ITEM 2, WITH 2-Iod NAILS. 2-Iod NAILS. 7.

27、NAIL UPPER BOARD. ITEM 6, TO LONGITUDINAL BOARD, ITEM I, WITH 4-Iod NAILS. NAVY) 4 4 4 4 4 4 REQD 6 5 4 3 2 I ITEM W UPPER BOARD HORIZONTAL SPACER VERTICAL SPACER LATERAL BOARD VERTICAL BOARD LONGITUDINAL BOARD DESCR IPTION ZX4X17 WOOD 12 X 4 X 19 WOOD IZX4X17 zx4x22 ZX4X116 LIST OF MATERIALS PAGE 7

28、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3320 -32A 81 I 9999933 0303757 7 4 MIL-STD-1320-12A (NAVY1 2 SEAL STEEL I I 1/4 X .O35 UNITIZING PROCEDURE I. USING A FORK LIFT TRUCK, PLACE ONE UNIT LOAD ON TOP OF ANOTHER. INSURE THAT THE STA

29、CKING FEATURES ARE ENGAGED. 4 2. STRAP UNIT LOADS TOGETHER BY THREADING THE STRAPS, ITEM I, UNDER THE ROUNDED SHELLS OF THE BOTTOM CONTAINERS AND THE SKIDS OF THE UPPER CONTAINERS. TENSION AND DOUBLE NOTCH SEAL USING ITEM 2. I 1/4 X .O35 X II FT I STRAP STEEL 3. REPEAT PROCEDURE FOR 3RD UNIT LOAD IF

30、 REQUIRED. REQD UNi MAD (IF REQUIRED) UNIT LOAD ITEM DESCRIPTION MATL/DWG DIMENSIONS UNITIZING UNIT LOADS IS RESTRICTED TO LOADING AND UNLOADING ONLY. LIST OF MATERIALS PREPARING ACTIVITY: REVIEW ACTIVITY: NAVY -OC. NAVY -OS (PROJECT NO. 8140-N9821 *U.S.COVERNMENT PN”C0FFICE: 1991-6O4-O3f 70014 AGE 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-