NAVY MIL-STD-1320-55-1981 TRUCKLOADING TRAILER ON FLAT CAR (TOFC) OR CONTAINER ON FLAT CAR (COFC) MINE UNDERWATER MK 53 AND MODS IN CRATE UNDERWATER MINE MK 52 MOD 0 DOMESTIC& UNDE .pdf

1、MILITARY STANDARD MIL-STD-13 20- 5 5 (NAVY) TRUCKLOADING 7 DECEMBER 198T Trai I er - On - F I at - C a r (T OF C) or Conta in er- On -FI at - Ca r ( C OF C) MINE, UNDERWATER MK 52 AND MODS IN CRATE, UNDERWATER MINE MK 52 MOD O DOMESTK AND UNDERWAY REPLENISHMENT UNIT LOADS SuPERSEDING wR-51/55 1 MARC

2、H 1968 UNIT LOAD DATA DIMENSIONS , 66 1/4LX493/4WX30H CUBE. 57.2 CUFT WEIGHT SEE TABLEI DOT HAZARD CLASSIFICATION - EXPLOSIVES A PAGE - ITEM GENERAL NOTES 2 FTL 40 FT. TRAILER (DF) 3 DETAILS 2,3 64 NOTES : I. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. 2. FOR CROSS REFERENCE TO ASSOCIATED

3、PALLETIZING, CONTAINERLOADING AND CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS, MI L-HDBK-236, rFsc 8140 _ AUTHORIZED AND RELEASED APPROVED BMUREAU OF EXPLOSIVES FOR TRAILER-ON-FLAT-CAR (TOFC) OR CONTAINER-ON-FLAT-CAR (COFC) SIGNATURE SUPERVISOR, MILITARY AND INTERMODAL SERVICES DATE U

4、SE. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-/- -_ -_- MIL-STD-1320 -55 1 7777711 00701B 3 9 - MIL-STD-1320- 5 5 (NAVY) GENERAL NOTES 1. THIS DOCUMENT GIVES DETAILED INSTRUCTIONS FOR LOADING UNIT LOADS OF UNDERWATER MINES MK 52 AND I,ODS IN DF

5、 EQUIPPED VANS WHEN SHIPPING THE VAN TRAILER-ON-FLAT-CAR (TOFC) OR CONTAINER-ON-FLAT-CAR (COK). THE UNDERWATER MINE MK 52 AND MODS SHALL BE IN CRATE, UNDERWATER MINE MK 52 AND MODS AND PALLETIZED PER DOMESTIC UNIT LOAD MIL-STD-1322-715 OR UNDERWbY REPLENISHMENT UNIT LOAD MIL-STD-1323-208. DF EQUIPPE

6、D VANS SHALL BE IN CONFORMANCE WITH AND SHIPPED ON FLAT CARS COMPLYING WITH BUREAU OF EXPLOSIVES PAMPHLET 6C. USE OF THE PLYWOOD SEPARATOR GATE (DETAIL B) IS PREFERRED DUE TO ITS EASE OF CONSTRUCTION AND LOW COST. HOW- EVER, A SEPARATOR GATE CONSTRUCTED OF 2 INCH THICK LUMBER (SEE DETAIL E, PAGE 4)

7、MAY BE USED WHEN PLYWOOD IS NOT AVAILABLE. DF CROSS MEMBERS SHALL BE POSITIONED AGAINST THE SEPARATOR GATES AS TIGHT AS THE ADJUSTMENT HOLES OF THE BELT RAILS PERMIT, 2. 3. 4. 5. WHEN POSITIONING CROSS MEMBERS, MAKE A VISUAL CHECK TO ENSURE THAT CROSS MEMBERS ARE LOCKED SECURELY IN PLACE. 6. UNLESS

8、OTHERWISE SPECIFIED, ALL MATERIALS SHALL BE IN ACCORDANCE WITH THE GENERAL TRUCKLOADING DOCUMENT, MIL-STD-1320. AFTER BLOCKING AND BRACING HAS BEEN INSPECTED, ATTACH SHIPPING DOCUMENTS TO REAR DUNNAGE. CLOSE AND SEAL DOORS AND ATTACH “EXPLOSIVES A” PLACARD TO ALL FOUR SIDES OF TRAILER. FOR GENERAL T

9、RUCKLOADING PROCEDURES REFER TO THE GENERAL TRUCKLOADING DOCUMENT, MIL-STD-1320. 7. 8. TABLE 1 )ODIC/NALC NO. un5 U776 u777 U791 U792 u793 u807 U808 U809 U823 U824 U825 U839 u840 U841 U846 u847 U848 MINE MK 52 MOD CONFIGURATION 1 B 1 C 1 D 2 B 2 C 2 D 3 B 3 C 3 D 4 B 4 C 4 D 5 B 5 C 5. D 6 B 6 c 6 D

10、 DO NOT USE FOR SHIPPING PURPOSES * DUL WT. FOR URULS ADD 10 LBS. * * DUL WT. FOR URULS ADD 160 LBS/TL TRUCKLOAD DATA WEIGHT IN LBS. A UNIT LOAD * TRUCKLOAD * 2606 41,696 2502 40,032 2374 37,984 2726 43,616 2602 41,632 2458 39,328 2624 45,184 2674 42,784 2714 43,424 2662 42,592 2538 40,M)B 2418 3e,m

11、 2746 43,936 2622 41,952 2510 40.160 2716 43; 456 2592 1 41,472 2452 39,232 NUMBER OF UNIT LOADS . TRUCKLOAD WEIGHT . SEE TABLE I NUMBER OF CROSS MEMBERS. NOTE- ANY ADDITIONAL CROSS MEMBERS RECEIVED IN 16 20 THE TRAILER MAY BE USED AT THE REAR OF THE LOAD TO ”BACKUP” THOSE PREVIOUSLY INSTALL- ED ON

12、THE 16”. 28”, 38 AND 48” BELT RAILS. OF TRAILER AND USING SEPARATOR GATES AS REQUIRED. , NOTE - LTL CAN BE MADE BY STARTING LOAD AT FRONT PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1320 -55 1 = 77777LL 0070189 5 *6 5 * * * 2 *1 PI

13、ECE NO. 2 X 4 DOUBLED w CLEAT UPRIGHT HORIZONTAL UPRIGHT PLYWOOD SHEET CLEAT DESCRIPTION DETAIL SEPARATOR 0 GATE w-0 8 REQUIRED 2 x 4 x 62 1/2 2 X 8 X 62 1/2 2 X 4 X TW-1/2 2 X 6 X 62 1/2 1/2 x 48 x TW-1/2 2X4X48 * THESE PIECES NOT REQUIRED WHEN USING SEPARATOR GATE, DETAIL B. fl * * THESE PIECES NO

14、T REQUIRED WHEN USING ALTERNATE SEPARATOR GATE, DETAIL E, (SEE PAGE4). 16 4 3/JOINT 16d 16 4 2/JOINT 12d 24 3,5 L6 24 4 ?/JOINT 12d 8 1 EVERYB“ 16d 32 LAMINATE EVERY8 “ 12d SEE - I NO. PCS. REQD SIZE I NAIL NUMBER I SIZE TO NAILS LIST OF MATERIALS L NAILING DATA SECTION C-C PAGE 3 FTL 40 FT. TRAILER

15、 (DF EQUIPPED) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-,i- -_- - MIL-STD-1320 -55 1 W 7777711 0070L70 1 MIL-STD-1320-55 (NAVY) WHEN USING ALTERNATE SEPARATOR POSITION TOP DF CROSS MEMBER AT BELT RAIL HEIGHT. POSITION VERTICAL MEMBERS (PIECE N

16、O. 3 8 5) AGAINST DF MEMBERS. I GATE, THEM)“ INSTALLATION OF ALTERNATE SEPARATOR GATE (SEE GENERAL NOTE 4, PAGE 2) ALTERNATE SEPARATOR GATE 8 REQUIRED (SEE GENERAL NOTE 4, PAGE 2) REVIEW ACTIVITY: NAVY - OS PAGE 4 PREPARING ACTIVITY: NAVY - OS (PROJECT NO. 8140-N523) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-