NAVY MIL-STD-1322-111-1991 UNIT LOAD FOR DOMESTIC AND OVERSEAS SHIPMENT AMRAAM CONTROL SECTION IN CONTAINER CNU-402 E OR AMRAAM WARHEAD SECTION IN CONTAINER CNU-403 E《CNU-402 E CNU.pdf

1、, i MIL-STD-1322 -111 1 W 9999911 0311911 384 MILITARY STANDARD UNIT LOAD M I L- STD - 13 2 2 - 111 CNAWI 29 JULY 1-1 FOR DOMESTIC AND OVERSEAS SHIPMENT AMRAAM CONTROL SECTION IN CONTAINER. CNU-402/E OR AMRAAM WARHEAD SECTION IN CONTAINER, CNU-403/E UNIT LOAD DATA CONTAINER CN -4OZE NUMBER OF ITEMS

2、PER CONTAINER I NUMBER OF CONTAINERS PER UNIT LOAD. 18 GROSS WEIGHT OF CONTAINER (LBSI 63.4 OROSS WEIGHT OF STEEL PALLET lLB51 72 WEIGHT OF WOO0 ANO STEEL STRAPPING LBSI 175 CUBE ICU FTI . 55.1 GROS5 WEIGHT OF UNIT LOAD ILBSI .A. . 1388 A DO NOT USE FOR SHIPPING WEIGHT DO NOT STACK MORE THAN 4 UNIT

3、LOADS HIGH IN 5TORAE. FOR HAZARD CLAS5IFICATIONS SEE NAVSEA OP 2165 CNU -403E I 18 78.9 72 175 1667 55.1 AMSC NO. - N/A NOTE : DISTRIBUTION STATEMENT A APPROVE0 FOR PUBLIC RELEASE : DISTRIBUTION IS UNLIMITED. UNLESS OTHERWISE SPECIFIEO, OIMENSIONS ARE IN INCHES. TOR CROSS REFERENCE TO ASSOCIATED TRU

4、CKLOADING. I I I I I CONTAINERLOAOING AND CARLOAOING MILITARY REV LTR I I DAT I TOA ISYSCOMI STANDARDS, REFER TO INOEX TO STANDARDS, m REVISION DESCRIPTION MIL-HDBK-236 INAVYI. APPROVAL I I I THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR SHIPPINB. HANDLING. STORAGE AND TRANSFER-AT-SEA. IT MAY ALSO B

5、E USED FOR DOMESTIC SHIPMENT IN COMPLIANCE WITH DOT REGULATIONS. /7 7/M 4/ ?/3 h/ TOA. WPNSTA EARLE MTE SIGNATURE AMSYSCOM BY DIRECTION MTE REQUIREMENTS FOR CONSTRUCTION OF MIS UNIT LOAD SHALL CONSIST OF THIS DOCUMENT AND ME LATEST ISSUE OF MIL-STD-1322 NAVY). / /d, AL- -7/&, LAT O RI G I NATO R WPN

6、STA EARLE. NEW JERSEY PAGE I OF 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322-111 (NAVY) PALLETIZING PROCEDURE 2 1. 2. 3 : 4. 5. 6. 7. 8. 9. 10 PROTECTOR BOARD WOOD 2 X 6 X 46 112 PJ 4 THREAD OUTSIDE LONGITUDINAL STRAPS, ITEM 2, BETW

7、EEN SECOND AND THIRD WIRES OF THE PALLET DECK AS SHOWN IN DETAIL B. THREAD CENTER LONGITUDINAL STRAP, ITEM 2, BETWEEN NINTH AND TE“ WIRES OF PALLET DECK AS SHOWN IN DETAIL B. POSITION TWO FLOOR ASSEMBLIES (SEE DETAIL D) ON PALLET DECK AS SHOWN IN DETAIL C. THERE SHALL BE EQUAL OVERHANG ON ALL FOR SI

8、DES OF THE PALLET. POSITION 18 CONTAINERS WITH SEPARATOR ASSEMBLIES ON THE PALLET DECK AS SHOWN IN DETAILS A AND C. DETAIL F SHOWS SEPARATOR ASSEMBLY CONSTRUCTION. POSITION PROTECTOR ASSEMBLIES, DETAIL E, OVER THE UNIT LOAD AS SHOWN IN DETAIL A. BRING LONGITIJDINAL STRAPS OVER THE UNIT LOAD. TENSION

9、 AND DOUBLE NOTCH THE SEALS AS SHOWN IN DETAIL A. FEED LATERAL STRAPS UNDER THE PALLET DECK AND OVER THE UNIT LOAD AS SHOWN IN DETAIL A. TENSION AND DOUBLE NOTCH THE SEALS. SECURE THE STRAPPING, ITEMS 2 AND 3, TO THE PROTECTOR ASSEMBLIES WITH STAPLES, ITEM 12, AS SHOWN IN DETAIL A. PARTIAL UNIT LOAD

10、S OF SIX OR TWELVE CONTAINERS ONLY ARE PERMITTED. EXTRA CONTAINERS MUST BE TREATED AS LOOSE ITEMS. MIXED UNIT LOADS OF CNU-4021E AND CNU-4031E CONTAINERS ARE PHUIIWED WDER THE FOLLOWING CONDITIONS: A) CNU-402/E AND CNU-4031E CONTAINERS ARE NOT MIXED WITHIN THE SAME LAYER. B) LAYERS OF CN-4031E CONTA

11、INERS ARE LOADED BELOW LAYERS OF CNU-402/E CONTAINERS. 9 SIDE PROTECTOR WWD ,I 2 X 6 X 36 DEPALLETIZING PROCEDURE 12 16 6 4 5 2 3 1 1. REMOVE STAPLES. 2. CVT AND REMOVE STRAPPING. 3. REMOVE PROTECTOR BOARD ASSEMBLIES. 4. REMOVE CONTAINERS AND SEPARATOR ASSEMBLIES. 5. RBIKnrE PUXJR ASSmLIES. 8 CROSS

12、PIECE PLYWWD 318 X 6 X 21 7 VERTICAL SEE NOTE 3 2 X 2 518 X 36 6 CROSS PIECE WOOD 1X6X21 5 PLANX WOOD 2X6X43 4 STRAP SEAL STEEL 314 SIZE 3 STRAP, LATERAL STEEL 314 X .O35 X 16 FT 2 STRAP, LONGITUDINAL STEEL 314 X .O35 X 16 FT 1 PALLET, MK 12 MOD 1 DWG 2645217 35 X 45 112 X 4 314 NOTES: 1. UNLESS OTH

13、ERWISE SPECIFIED, ALL MATERIALS SHALL BE IN ACCORDANCE WITH MIL-STD-1322 (NAVY). 2. DO NOT USE TYPE I STRAPPING WITH POWER MACHINES. 3. ITEM 7 CAN BE HADE FROM 2 X 4 STOCX CUT DOWN IN WIDTH TO SIZE. LGE 2 I 1 I 11 I SEPARATR I PLYWOOD 1 318 X 42 X 36 I I REQ. I ITEM 1 DESCRIPTION I MATL/DWG I DIMENS

14、IONS I I LIST OF MATERIALS I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-STD-1322 -111 1 9999931 0311913 157 MIL-STD1322-111 (NAVY) I SEE DETAIL B DETAIL ARROWS INDICATE FORWARD END OF CONTAINER. n SEE DETAIL F DETAIL PALLBT DECK AS SHOWN.

15、7 DETAIL 0 PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -111 83 M 9999933 0333934 093 1 MIL-STD-1322-111 (NAVY) DETAIL 0 FLOOR ASSEMBLY ASSQISLB Wf4d NAILS. -0 CAN BE CUT FROM ax4sm DETAIL 0 PROTECTOR ASSEMBLY NAIL ITEM TO ITM 9 W/2-6d NAILS PER JOINT. DETAIL 0 SEPARATOR ASSEMBLY ASSEIIBLE W/6d NAILS. REVIEW ACTIVITY: NAVY-AS ,OS PAGE 4 PREPARING ACTIVITY: NAW-OS (PROJECT NO. 8140-N984) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-