NAVY MIL-STD-1322-113-1992 UNIT LOAD MK 165 MOD 0 ADAPTER SILL ASSY《MK165MOD0适配器基石集合装载》.pdf

1、MIL-STD-1322 -113 m 9999933 0434237 741 m REV TDA SYSCOM L TR REV IS ION DESCRIPTION DATE APPROVAL MIL-STD-1322-113 NAW1 M I L I TA RY STAN D AR D 14 AUGUST 1992 UNIT LOAD MK 165 MOD O ADAPTER SILL ASSY STANDARDS, REFER TO INDEX TO STANDARDS, MIL -HDBK-236 INAVYI. h UNIT LOAD DATA NUMBER OF SILL ASS

2、YS PER UNIT LOAD. GROSS WEIGHT OF ONE SILL ASSY - - - WEIGHT OF STEEL PALLET- - - -. - - - - - - - _ _- - 90 LBS. WEIGHT OF STEEL STRAPPING- - - - WEIGHT OF DUNNAGE- _ - - - - - - - - - - - GROSS WEIGHT OF UNIT LOAD- - - - - CUBE- - - - - - - - - - - - - - - - - - - - - - - _ - -40 CU/FT - -. ._._ 8

3、 _ - - - -. _ _-113.9 LBS. - - - - - - - -.5 LBS. _- -68 LBS. - - - - - - -_- 1074 LESA A DO NOT USE FOR SHIPPING WEIGHT DO NOT STACK UNIT LOADS IN STORAGE OR TRANSIT FOR HAZARD CLASSIFICATION SEE OP 2165 UP-RIGHT POSITION UP-SIDE DOWN POSITION PA5 NO. - N /A MIS UNIT LOAD IS AUTHORIZED AND RELEASED

4、 FOR DEPOT HANDLING AND STORAGE AND FOR SHIPMENT BY COMMON CARRIER. 8-s - 5%- WPNSTA EARLE SIGNATURE NAVSEASYS& BY DIRECTION DATE REQUIREMENTS FOR CONSTRUCTION OF MIS UNIT LOAD SHALL CONSIST OF THIS DOCUMENT AND ME LATEST ISSUE OF MIL-STD-1322 (NAVY). 2/b/j L DATE OR1 GI NATOR x A/ /IA WPNSTA EARLE.

5、 NEW JERSEY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3322 -333 m 9999933 0434238 b88 m +- a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -113 D 9999911 0434239 514 I. 2.

6、 3. 4. 5. 6. 7. 8. 9 PALLETIZING PROCEDURES PLACE (2) LONGITUDINAL STRAPS, ITEM 5, THROUGH OF PALLET AS SHOWN IN DETAIL A. PLACE (2) PLYWOOD SEPARATOR BDS, ITEM 2, OVERHANG ON ALL SIDES AS SHOWN IN FIG 1. ON THE 5th AND 6th WIRES PALLET WITH EQUAL PLACE (4) MK 165 MOD O SILL ASSYS EQUALLY SPACED IN

7、UP-RIGHT POSITION ON SEPARATOR BDS AS SHOWN IN FIG I. PLACE (I) PC OF PLASTIC SHEET, ITEM 3, OVER SILL ASSYS WITH EQUAL OVER HANG ON ALL SIDES. PLACE (2) PCS OF SEPARATOR ED. ITEM 2, OVER SILL ASSYS AS SHOWN IN FIG 1. PLACE (4) MK 165 MOD O SILL ASSYS IN UP-SIDE DOWN POSITION OVER SEPARATOR BDS, ITE

8、M 2, AS SHOWN IN FIG 2. PLACE (1) PC OF PLASTIC SHEET, ITEM 3, OVER SILL ASSYS WITH EQUAL OVER HANG ON ALL SIDES. PLACE (2) PCS. OF SEPARATOR ED, ITEM 2, OVER SILL ASSYS AS SHOWN IN FIG 3. PLACE (2) TOP SEPARATOR BDS, ITEM 2, OVER SILL ASSYS. COVER ENTIRE LOAD WITH PLASTIC SHEET, ITEM 4. SEE FIG 3.

9、*NOTE: FINAL PLASTIC SHEET, ITEM 4, MUST COVER ENTIRE LOAD, IT IS PERMISSIBLE TO OVERLAY AN EXTRA SHEETTO MEETTHIS REQUIREMENT. TENSION AND SECURE ALL STRAPPING ITEMS, 5 & 6 WITH DOUBLE NOTCH SEALS, ITEM 8. SECURE TOP LAYER OF PLASTIC SHEET. ITEM 4, WITH STAPLES, ITEM 9, AS SHOWN IN FINAL UNITIZED V

10、IEW MARKING: MIL-STD-1322-113 (NAVY) . T / IN ADDITION TO ANY SPECIAL MARKING REQUIRED BY CONTRACT OR ORDER, THE UNIT LOAD SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-1322 (NAVY). STENCIL ON EACH PIECE / OF PLYWOOD IN APPROX PO.LXION SHOWN WITH 1 f2 HIGH CHARACTER USING ITEM 10, IN A CONTRASTING COLO

11、R, “REUSEABLE DO NOT DESTROV HANDLE WITH CARE DEPALLETIZING PROCEDURE a. CUT AND REMOVE STRAPPING. b. C. d. REMOVE MIDDLE PLASTIC SHEET. e. f. NOTE: SPECIAL CARE SHOULD BE TAKEN WHEN BREAKING DOWN THESE UNIT LOADS, AS THE MATERIALS OTHER THAN THESTEELSTRAPPINGCANBESTOREOANOREUSED. CAREFULLY REMOVE S

12、TAPLES FROM TOP PLASTIC SHEET. REMOVE PLASTIC SHEET AND TOP (2) SEPARATOR BOARDS. CAREFULLY REMOVE (4) SILL ASSYS. REPEAT PROCEDURES c-e FOR REMAINING SILL ASSYS. 1. UNLESS OTHERWISE SPECIFIED, ALL MATERIALS SHALL BE IN ACCORDANCE WITH MIL-STD- 1322 (NAVY). AR I 10 I INKSTENCIL 1 A-A-208 DESCRIPTION LIST OF MATERIALS PREPARING ACTIVW: NAVY-OS (PROJECT NO. 8140-N1027) PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-