NAVY MIL-STD-1323-313 A-1987 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE 5 125 INCH MK 214 MOD 0 NATO SEA GNAT RF SEDUCTION AND MK 216 MOD 0 NATO SEA GNAT RF DISTRACTION IN PALL.pdf

1、MIL-STD-1323 -313A 1 m 7777712 00715Bb 7 m s- 3 7-0s- MILITARY STANDARD MIL-STD-1323-313A 21 APRIL 1987 (NAVY) UNIT LOAD FOR UNDERWAY REPLENISHMENT SUPERSEDING CARTRIDGE, 5.125 INCH, MK 214 MOD O FIIL-STD-1323-313 2 NOV 04 NATO SEA GNAT RF SEDUCTION AND MK 216 MOD O NATO SEA GNAT RF DISTRACTION N PA

2、LLET ADAPTER, MK 144 Gu22 3W80 INIT loAD - DATA .- DODICINALC NO. (MK 2111) (MK 216) 1 12 NUFER OF CARTRIDGES PER CONTAINER NUEBER OF ADAPTER UNITS PER UNIT LOAD 2 2 NUEBER OF CARTRIDGES PER UNIT LOA0 24 GROSS WEIGHT OF ONE ADAPTER UNIT 782 LBS 1 12 . . NUEBER OF CONTAINERS PER ADAPTER UNIT 24 65 LB

3、S 8Y2 L8S GROSS WEIGHT OF ONE CONTAINER . 60 LBS . EIGHT OF STEEL STRAPPING . 12 LBS UEIGHT OF ADAPTERS 2 R 58 LBS 116 LBS UEIGHT OF PALLET 911 LBS 94 LBS I/* GROSS WEIGHT OF UNIT LOAD . 1662 LESA 1790 LBSA CUBE 12.1 CU FT 42.1 CU FT HAZARD CLASSIFICATION DOT . CLASS C 12 L8S SHIPPING CONDITIOI DRAW

4、ING RF SEDUCTION 53711 - 6133075 RF DISTRACTION 53711 - 6348315 CLASS B CG CLASS II 8 CLASS II B ADO NOT USE FOR SHIPPING UEIGHT O0 NOT STACK MORE THAN 5 UNIT LOADS HIGH IN STORAGE AMSC NO. - N/A iOTES: 1. UNLESS OTHERUISE SPECIFIED. DIMENSIONS ARE IN INCHES. 2. FOR CROSS REFERENCE TO ASSOCIATED TRU

5、CKLOADING. CONTAINERLOADING AND CARLOADING MILITARY STANDARDS. REFER TO INDEX TO STANDARDS MIL-HDBK-236 (N4VY). - APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR SHIPPING, HANDLING, STORAGE AND TRANSFER-AT-SEA. IT MAY ALSO BE USED FOR OF THIS UNIT

6、 LOAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1323 (NAVY) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1323 -313A 81 7777711 0071587 O MI 1-STD-13 23 -31 3A (NAVY) PALLETIZING PROCEDURE THREAD STRAPPING, ITEM 7, BETW

7、EEN THE DECK WIRES OF THE PALLET, ITEM 1, AS SHOWN IN DETAIL A. THREAD STRAPPING, ITEM E, THROUGH THE SQUARE OPENINGS IN THE PALLET DECK AS SHOWN IN DETAIL A. POSITION STRAPPING, ITEM 5, USED TO UNITIZE MODULE, ON PALLET ABOVE STRAPPING, ITEM 7, AS SHOWN IN DETAIL 3. THREAD STRAPPING, ITEM 6, THROUG

8、H THE STRAP LOOPS OF THE FRONT AND REAR FRAMES, ITEMS 2 AND 3, AND POSITON THE FRAMES ON THE PALLET AS SHOWN IN DETAIL B. POSITION TWO CONTAINERS IN THE CORNERS OF THE FRAMES WITH THEIR COVER ENDS AGAINST THE FLANGE OF THE FRONT FRAME, ITEM 2, AND THEIR BOTTOM ENDS ON THE SPACER BLOCKS OF THE REAR F

9、RAME, ITEM 3, AS SHOWN IN DETAILS 3 AND C. POSITION A THIRD CONTAINER BETWEEN THE TWO CONTAINERS WITH THE COVER END AGAINST THE FLANGE OF THE REAR FRAME. POSITION THE REMAINING THREE ROWS OF CONTAINERS, ALTERNATING THE DIRECTION OF THE CONTAINERS BETWEEN ROWS, AS SHOWN IN DETAIL B. POSITION THE TOP

10、FRAME, ITEM 4, OVER THE FRAMES AND CONTAINERS WITH THE TWO SPACER BLOCK END OVER THE FRONT FRAME. POSITION STRAPPING, ITEM 5, IN THE CORNER NOTCHES AND OVER THE TOP FRAME. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 9. THREAD STRAPPING, ITEM 6, THROUGH THE OUTBOARD STRAP LOOPS OF THE FRONT AND REAR FRAM

11、ES. TENSION AND DOUSLE NOTCH THE SEAL, ITEM 9. REPEAT STEPS (c) THROUGH (i) FOR THE SECOND ADAPTER UNIT. THREAD STRAPPING, ITEM E, UP THROUGH THE STRAP LOOPS OF THE FRONT AND REAR FRAMES AND OVER THE TOP FRAMES. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 9. POSITION STRAPPING, ITEM 7, TO SECURE LOAD TO

12、 PALLET,OVER THE ADAPTER UNIT STRAPPING, ITEM 5. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 9. MARKING: THE UNIT LOAD SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-1323 (NAVY). SEE NOTES: I. .O31 COLD ROLLED, HEATTREATED, WY BE SUBSTITUTED. 2. DO NOT USE TWEI STRAPPING WITH POWER TOOLS. DEPALLETIZING PROC

13、EDURE (a) CUT AND REMOVE THE PALLETIZING STRAPPING, ITEM 7 AND E. piKq DO NOT CUT ADAPTER UNIT STRAPPING, ITEMS 5 AND 6, IF THE ADAPTER UNITS ARE TO E HANDLED/TRANSFERRFD BEFORE REMOVING THE CONTAINERS. CUT AND REMOVE THE ADAPTER UNIT STRAPPING, ITEMS 5 AND 6. (c) REMOVE TOP FRAME. (d) REMOVE CONTAI

14、NERS. (e) (b) REMOVE FRONT AND REAR FRAMES. PAGE 2 I 1 I 1 I PALLET, MK 3MODOI STEEL Ilml -564200 I40x48x43/4 REO. ITEM DESCRIPTION MATL MATL SPEC. DIMENSION! LIST OF MATERIALS r s Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1323 -313A 1

15、m 7777711 00715 2 m MIL-STD-1323-313A (NAVY) THREAD STRAPPING DOWN THROUGH THE SQUARE WHICH IS 2ND FROM THE END AND 3RD FROM THE SIDE. THREAD STRAPPING BETWEEN THE 6TH AND 7TH WIRE DETAIL 0 EDGE NOTCH I KEY B = BOTTOM END C=COVER END - SEE DETAIL 4 APPLY THIS STRAP FIRST POSITON ON PALLET DECK IN LI

16、NE WITH EDGE NOTCHES POSITION FRAMES WITH 1 INCH OVERHANG IN BOTH DIRECTIONS ADAPTER UNIT ASSEMBLY THREAD THROUGH STkAP LOOPS ON INBOARD SIDE BEFORE PIACING ADAPTER FRAMES ON PALLET POSITIONING OF END FRAMES REVIEU ACTIVITY NAVY - os PREPARING ACTIVITY: WVY - os (PROJECT NO. 8190-N796) PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-