NAVY MIL-STD-1323-370-1991 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE COUNTERMEASURES PRACTICE MK 229 MOD 0 CARTRIDGE COUNTERMEASURES 5 125 INCH DUMMY MK 232 MOD 0 IN PALLET AD.pdf

1、MIL-STD-1323 -370 81 9999911 0899348 1 - _ - MILITARY STANDARD MI L- STD- 1323- 370 UNIT LOAD FOR UNDERWAY REPLENISHMENT (NAVY1 i1 FEBRUARY 1991 CARTRIDGE, COUNTERMEASURES, PRACTICE, MK 229 MOD O CARTRIDGE. COUNTERMEASURES, 5.125 INCH, DUMMY, MK 232 MOD O IN PALLET ADAPTER, MK 144 UNIT LOAD DATA MK

2、2291 (MK 232) DODIC/NALC . 4W61 5w95 NUMBER OF CARTRIDGES PER CONTAINER . 1 I NUMBER OF CONTAINERS PER ADAPTER UNIT 12 12 NUMBER OF ADAPTER UNITS PER UNIT LOAD. . 2 2 NUMBER OF CARTRIDGES PER UNIT LOAD. 24 24 GROSS WEIGHT OF ONE CONTAINER ILBCI . 60 60 GROSS WEIGHT OF ONE ADAPTER UNIT ILBSI . 782 78

3、2 WEIGHT OF ADAPTERS 12 AT 58 LBSI ILBS) 116 I I6 GROSS WEIGHT OF STEEL PALLET ILBSI 90 90 WEIGHT OF STEEL STRAPPING ILBSI . 12 12 GROSS WEIGHT OF UNIT LOAD ILBSI .A. -1658 1658 CUBE (CU FTI . 42.1 42.1 DOT HAZARD CLASS. c INERT Ci3 CLASS. . I INERT . 7 Il6 DIA a DO NOT USE FOR SHIPPING WEIGHT DO NO

4、T STACK MORE THAN 5 UNIT LOADS HIGH IN STORAGE- AMSC NO. - N/A DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC RELEASE: DISTRIBUTION IS UNLIMITED. NOTE : UNLESS OTHERWISE SPECIFIED, DIMENCIDNS ARE IN INCHES, FOR CROSS REFERENCE TO ASSOCIATED TRUCKLOADING, CONTAINERLDADING AND CARLOADING MILITARY REV LT

5、R MIL-HDBK-236 INAVY). m REVISION DESCRIPTION DATE APPROVAL THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR SHIPPING; HANDLING, STORAGE AND TRANSFER-AT-SEA. IT MAY ALSO BE USED FOR DOMESTIC SHIPMENT IN COMPLIANCE WITH DOT REGULATIONS. REQUIREMENTS FOR CONSTRUCTION OF THIS UNIT LOAD SHALL CONSIST OF TH

6、IS DOCUMENT AND THE LATEST ISSUE OF MIL-STD-1323 (NAVY). 5.P . L8si DATE OR1 GI NATOR WPNSTA EARLE. NEW JERSEY I PAGE 1 OF 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3323 -370 BI 9999933 O099349 3 MIL- STD- 1323- 370 (NAVY) UNITIZING P

7、ROCEDURE IA1 THREAO LONGITUDINAL STRAPS, ITEM 7, THROUGH THE OECK WIRES OF THE PALLET, ITEM I, AS SHOWN IN DETAIL A. 181 THREAO LATERAL STRAPS, ITEM 8, THROUGH THE SQUARE OPENINGS IN THE PALLET OECK AS SHOWN IN DETAIL A. ICI POSITION LONGITUDINAL STRAPPING, ITEM 5, USE0 TO UNITIZE MOOULE, ON THE PAL

8、LET DECK ABOVE STRAPPING, ID1 THREAO HORIZONTAL STRAPPING, ITEM 6, THROUGH THE STRAP LOOPS OF THE FRONT AND REAR FRAMES, ITEMS 2 (El POSITION TWO CONTAINERS IN THE FRAMES WITH THEIR COVER ENDS AGAINST THE FLANGE OF THE FRONT FRAME, ITEM 2, IF1 POSITION A THIRD CONTAINER BETWEEN THE TWO CONTAINERS WI

9、TH THE COVER EN0 AGAINST THE FLANGE OF THE REAR FRAME. IGI POSITION THE REMAINING THREE ROWS OF CONTAINERS, ALTERNATING THE DIRECTION OF THE CONTAINERS BETWEEN (HI POSITION THE TOP FRAME, ITEM 4, OVER THE FRAMES ANO CONTAINERS WITH WITH THE TWO SPACER BLOCK END III POSITION STRAPPING, ITEM 5, IN THE

10、 CORNER NOTCHES AND OVER THE TOP FRAME. TENSION AND OOUBLE NOTCH IJI THREAD STRAPPING, ITEM 6. THROUGH THE OUTBOARD STRAP LOOPS OF THE FRONT AND REAR FRAMES. TENSION AND IKI REPEAT STEPS ICI THROUGH III FOR THE SECOND ADAPTER UNIT. IL1 THREAO STRAPPING, ITEM 8, UP THROUGH THE STRAP LOOPS OF THE FRON

11、T ANO REAR FRAMES ANO OVER THE TOP (Ml POSITION STRAPPING, ITEM 7, TO SECURE LOAD TO PALLET, OVER THE ADAPTER UNIT STRAPPING, ITEM 5. TENSION MARK IN G : ITEM 7, AS SHOWN IN DETAIL B. ANO 3, AND POSITION THE FRAMES ON THE PALLET AS SHOWN IN DETAIL B. AND THEIR BOTTOM END5 ON THE SPACER BLOCKS OF THE

12、 REAR FRAME, ITEM 3, AS SHOWN IN DETAILS B ANO C. ROWS, AS SHOWN IN DETAIL B. OVER THE FRONT FRAME. THE SEAL, ITEM 9. OOUBLE NOTCH THE SEALS, ITEM 9. FRAMES. TENSION ANO OOUBLE NOTCH THE SEALS, ITEM 9. AND DOUBLE NOTCH THE SEALS, ITEM 9. IN ADDITION TO ANY SPECIAL MARKING REQUIRE0 BY CONTRACT OR ORD

13、ER, THE UNIT LOAD SHALL BE MARKE0 IN ACCORDANCE WITH MIL-STO-I323 INAVYI. HESE STRAPS FIRST NOTE STRAP LOOP ENDFRAMESMAYNEEDSUPPORT SEE DETAILS A AND B DURING LOADING (SEE STEPS e, f, AND g) TO PREVENT TOPPLING. NOTES: DEUNITIZING PROCEDURE IA1 CUT ANO REMOVE STRAPPING, ITEM 7 ANO 8 I CAUTION 1 O0 N

14、OT CUT ADAPTER UNIT STRAPPING, ITEMS 5 AND 6. IF THE ADAPTER UNITS ARE TO BE HANOLEO/TRANSFERREO BEFORE REMOVING THE CONTAINERS. IBI CUT ANO REMOVE THE ADAPTER UNIT ICI REMOVE TOP FRAME. I01 REMOVE CONTAINERS. IEI REMOVE FRONT ANO REAR FRAMES. STRAPPING ITEMS 5 AND 6. ALL MATERIALS SHALL BE IN ACCOR

15、DANCE WITH THE BASIC DOCUMENT, MIL-STO- 1323 (NAVY). DO NOT USE TYPE I STRAPPING WITH POWER MACHINES. IO 9 SEAL STEEL 3/4 21 8 ILATERAL STRAP I STEEL ?44=$ .O35 X .I . , 3/4 X .O35 X 15 FT 2 7 LONGITUDINAL STRAP STEEL 3/4 X ,035 X 14 FT 4 6 HORIZONTAL STRAP STEEL 2 5 LONGITUDINAL STRAP STEEL 3/4 Ili

16、 FT X .O35 X FRAME, REAR 20 5/8 X 6 IR (ADAPTER MK 1441 40 X 48 X 4 314 (REQD ITEM 1 DESCRIPTION I MATLIDWG IDIMENSIONS PAGE 2 I LIST OF MATERIALS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- STD- 1323-370 (NAWI READ STRAPPING WWN THROUGH THE

17、 UARE WHICH IS 2ND FROM THE-END D 3RD FROM THE SIDE. EDGE NOTCH DETAIL A APPLY THIS STRAP FIRST THREAD THROUGH STRAP LOOPS / DETAIL ON INBOARD SIDE BEFORE PLACING ADAPTER FRAMES ON PALLET ADAPTER UNIT ASSEMBLY Dm DETAIL C POSITIONING OF END FRAMES REVIEW ACTIVITY: NAVY -OS PREPARINQ ACTIVITY: NAVY-OS PROJECT NO. 8140-NS581 PAGE *U.S. GOVERNMENT PRINTING OFFICE: 1991-504-034/50258 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-