NAVY MIL-T-10695 A-1952 TEST SETS SHUTTER SPEED (CAMERA TS-703( ) UF)《TS-703()超精摄像头快门速度测试装置》.pdf

1、- - - -I . 4 -8 F - tf5- A7 “ MIL-T-LOb95A 67 m 9999906 0148729 4 = MIL-Tq695A 24 NOVEMBER 1962 SUPERSEDING MIL-S-l0695(SigC) 17 NOVEMBER 1960 MILITAY SPECIFICATION TEST SETS, SHUlTER SPEED (CAMERA TS-703( )/U?) Th 260 volts. NN-3401 -Boxes, Wood-Cleated- Plywood (For Domestic Shipment), NN-l3-621 -

2、Boxes, Wood, Nailed and Lock-Corner. Q-S-671 -Solder, Soft (Tin, Tin- Lead and Lead-SiIver). UU-T-111 -Tape, Paper, Gummed (Sealing and Securing). MILITARY JAN-1A -Tubes, Electron, JAN-GO -Capacitors, Mica-Dielec- tric, Fixed. MTGM-6 -Met ers, Elect r ical-Indi- cating; Panel Qpe. JAN-1-10 -Insulati

3、ng Mat er ials, Ceramic, Radio Class L, JAN-R-11 -Resistors, Fixed Com- position. MIL-P-14 -PlasthMaterit Ther- mosetting. JAN-R-22 -Rheostats, Wire Wound, Power, Type. JANS-23 -Switches, Toggle (For Electronic and Communications Use), JAN-C-26 -Capacitors, Direct Cur- rent, Paper Dielectric Fixed (

4、Herme- tically Sealed in Metallic Cases). JAN-R-26 -Resistors, Fixed Wire- Wound, Power Type. MILT-27 -Transformers and In- ductors (Audio and Power). JAN-S-28 -Sockets, Electron-Tube and Accessories. JAN-R-29 -Resistors, External Me- ter (Bigh Voltage, Ferrule Terminal MIGP-76 -Packaging, Packing a

5、nd Container-Marking Tubes, Electron. Type) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-JAN-G7G -Cable (Hook-Up Wire), Electric, Insulated, Radio and Inrstru- ment. MLP-78 -PlaEitic-Material, Lam- nated, Thermosetting (For Designa- tion Plates).

6、MIL-i?-79 Plastic-Materials, Lami- nated, Thermosetting Rods and Tubes. JAN-43-91 -Capacitors, Paper- Dielectric, Fixed (Nonmetallic Cases). JAN-R-93 Res i s t or s, Ac cur at e, Fixed, Wire-Wound. JAN-R-94 -Res ist or EI, Variable Composition. JAN-P-105 -Packaging and Packing for Overseas Shipment-

7、Boxa, Wood, Cleated Plywood. JAN-P-106 -Packaging and Packing for Overseas Shipment-Boxes, Wood, Nailed. M General Procl esses for. MIL-V-173 Varnish, Moisture- and Fungus-Resistant, For Treatment of Communications, Electronic and As- sociated Electrical Equipment. JAN-R-184 -Resistors, Fixed, Wh Wo

8、und (Low Power). MIL1431 -Insulation, Electrical, Synthetic-Resin Composition, Non- rigid. JAN-P-668 -Packaging and Packing of Electrical muipment and Spare Parts (Electronic, Electrical, and Elec- tro-Mechanical) . JAN-A469 -Anti-Seize Compound, White Lead Base, General Purpose (for Threaded Fittin

9、gs). JAN-T-713 -Twine, Lacing and Ty- ing, Electrical and Electronic Equip ment. MIGp-997 -Plastic-Material, Lturii- nated, Thermosetting; Electrical-In- sulating ; Sheets, Glass Cloth, Silicone Resin. MIL-P-31 15 -Plastic-Mat erial, Lamil nated, Thermosetting, Sheeta, Paper Base, Phenolic-Resin. MI

10、GP-3408 -Piastic-Material, Mold- ing; Rigid Thermoplastic, Aniline Formaldehyde. MIL-P-3409 -Plastic-Material, Mold- ing ; Rigid Thermoplastic, Polydichlo- rostyrene. MIL-P-3410 Plastic-Material, Mold- ing; Rigid Thermoplastic, Polyvhyl Chloride and Copolymers Thereof. MIGP-3411 Plastic-Material, Mo

11、Td- ing ; Rigid Thermoplastic, Vinylidene Chloride. MIL-P-3412 -Piastic-Material, Mold- ing; Rigid Thermoplastic, Ethyl Cel- lulose. MIGP-3413 -Plastic-Material, Mold- ing ; Rigid Thermoplastic, Polystyrene. MIL-P-8414 Plastic-Material, Mold- ing; Rigid Thermoplastic, Cellulose Acetate Butyrate. MIG

12、P-3416 -Plastic-Material, Mold- ing; Rigid Thermoplastic, Cellulose Acetate. MILp-3416 Plastic-Material, Mold- ing ; Rigid Thermoplastic, Acrylic. 2 . , , , j Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproductio

13、n or networking permitted without license from IHS-,-,-(Copies of Underwritere Laborataries, Inc., Sub- ject 62, “Standard for Flexible Cord and Fixture Wire” may be obtained from that organization at 181 Sixth Avenue, New York, N. Y.) 3. REQUIREMENTS 3.1 Preproduction samples.-After award of contra

14、ct, the contractor shall proceed with fabrication of material and shall assem- ble samples of each equipment on order, using tools and methods similar to those which will be used in quantity production. The quantity of samples shall be as follows: For workmanship and performance : 2 test sets, shutt

15、er speed (Camera TS-703( )/UF). These samples, together with test data show- ing complete compliance with this specifica- tion, shall be submitted to the Government agency as specified (see 6.2). The test data shall comprise an engineering report stat- ing all essential details of the testing equip-

16、 ment (manufacturers model, serial number, and date of calibration), test procedure, ob- servations and other data, calculations, and test results, Approval of the submitted sam- ples shal not be construed as authorizing any deviations from the requirements of this specification. 8.1.2 Mayking and s

17、hipping.-?reproduc- tion samples shall be marked and shipped by the contractor as specified (see 6.2). 3.1.8 Approval. - Preproduction samples will be inspected by the Government agency, for compliance with the applicable specifica- tiom and drawings. if any samples are is- approved, the contractor

18、may be required to igubmit additional samples until the required quantity of satisfactory samples has been submitted. Such additional samples shall be accompanied by a description of the changes made to correct the faults of the rejected samples. SS.4 Standards of prodt any reeultiag loose flakes of

19、 rosin shall be care- fully removed from the inside of the equip ment, Imulatfn material that has been sub- jected t heating during the soldering opera- tion shall be undamaged and parta faatend thereto shall not have become loosened, 3,7 Wire, hookup.-Wherever practicable, hookup wire shall be stra

20、nded. Conductor aize shall be sufficient to avoid reduction in expected service life ob the equipment, caused by deterioration in electrical properties of the wire from overheating. S.7.1 Bart3 hokp wire. - Bare hookup wire shall not be used unless insulated wire is Impracticable because of circuit

21、character- istics or shortness of the wire run. Where used, bare hookup shall conform to ASA Standard H4.4. 8.7.2 Insulated hookup wire. - Insulated hookup wire shall conform to the following: Waxhum potentlat to grorcnd (zroltr ma a,a4 OP squirt, ad.) Oto 600 Bao to 1000 600 to 1000 600 to 2600 Ove

22、r 2600 Type PSU tpecipscCEion WL JAN-C-76 SRIR JAN-G76 SRRF JAN-(3-76 SRHV JAN476 Ae approved by the bureau or agency concerned for each application. 3.8 Wiring and cabling.-Wiring and ca- bling shali be neat and sturdy. 3.8.1 Cabliitg.-Insulated wires shall be formed into cables except when perform

23、ance of the equipment would be adversely affected thereby or where it is mechanically imprac- 6 ticable as in the case where the renuiting cablw would be excesnively hge and would interfere with the operation or maintenance of the equipment. The cabling of wires shall be effected by twine conforming

24、 to Spedti- cation JAN-T-713, or by vinyl-chloride-. acetate-backed, prwsure-sensitive tape, type VF, conforming to Spedfication ML-T- 15126 except that the tape shall be natual color. 3.8.2 SlacB.-Whe and cables shsll be au short as practicable except that sutrident slack shall be provided to (a) p

25、revent undue stress on cable forms, wires, and connec- tions, (b) enable parts to be removed and replaced during servicing without discon- necting other parts, and (c) facilitate field repair of broken or cut wires. 3,8.3 Protection.-Wirea and cables ive effects, unless used _ of the equipment, will

26、 3.8.10.2 Shielding on wire and cable. - Shielding on wire or cable shall be grounded to the chassis or frame, in the manner speci- fied in 3.8.10.1 and shall end at a sufficient distance from exposed conductors to prevent shorting or arcing between the conductor and the shielding- num practicable.

27、3.8.9 Cect.oldeng leads, lugs, and terminals shall be tinned, silver-plated, ubject to break- le provided with Rire insulation, used on tinned, dio circuits, but 3.8.11 Zdmti$cath of wiring. - Wiring shall be identified by suitable color-coding or, if approved by the contracting officer, may be iden

28、tified by other means such a8 marking of terminals at both ends of each A be soldered. - . - .- lead. -,dered to temi- OnCe and not 3.9 Power cordage.-The power cord shall e be- be 8 feet long insulated in accordance with means be Specification 71-4946 and in addition shail sulat;ion ends Of wires -

29、L . ._. be type “S“ conforming to Underwriters ng by Laboratories Standards for Flexible Cord- Of varnish On- and Fixture-Wire. One end shall be perma- nently attached to the equipment and the other end shall be equipped with a stand- to ard hard rubber 10 ampere-260 volt, non- ! parts e- crushable

30、parallel blade attachment plug cap -a not be made meeting the requirements of Specification ai circuits but only to w-ie marked on spare parts. 3.12.4.2 Cables and cable assemblim.-ahe typenumber *portion of applicable Joint Army-Navy or Signal Corps nomenclature shall be marked on each cable or cab

31、le as- sembly, by moldine or use of an identifica- tion tag conforming to Drawing SCLA- 21826 and fastened securely around the cable. 3.12.4.3 Fu.ses and bmps.-Reference dee- ignations shall not be marked on fusw or lamps. The reference designation of the fuse or lamp shall be marked adjacent to the

32、 fuse holder or 14mp socket. Where space is limited, the reference designation of the fuse holder or lamp socket may be omitted to provide space for the reference designa- tion of the fuse or lamp. 3.12.4.4 Electron tubes.-Reference desig- nations shall not be marked on electron tubes. The type numb

33、er and reference desig- nation of each tube shall be marked adjacent to the tube. Type numbers of tubes shall be as marked on the tubes except that the letters “JAN” shall be omitted. Where space is limited, the reference designation for the socket may be omitted to provide space for the reference d

34、esignation and type number of the tube. When space is not avail- able for marking the required tube refer- ence designations and type numbers, a suit- able label showing location of the tubes and the corresponding reference designations shall be mounted inside the component where it will be readily

35、visible when viewing the tubes. mT-aQ6* 8.12.4.6 0th letPd gartS.-EXC 8LI otherwise specified in 3.12.4.3 and 3.12.4.4 the regerence designation for each part hav- ing electrical circuits or connections ahall be marked 9n an adjacept surface but if space is not available there the refererice designa

36、- . tion shall be marked on the part itself. 3.12.4.6 Nonekctrkd parts.-The refer- ence designation for each nonelectrical part except screws, nuts, washers, bushings, and similar small hardware shall. be marked on the chqssis, frame, panel, etc., immediately adjacent to the part but if space is not

37、 avail- able there the referenced designation shall be marked on the part itself. 3.52.5 Method of marking. - Except ati otherwise specified, marking shall be ap plied by the following means, in such manner as to be legible and permanent: Wolding Die Stamping *Glyceryl- Engraving *Rubber Ehhing Stam

38、ping *Permanent ink Steel Stamping *Sik Screening *Stenciling ?hthalatePaint Labeln 3.12.6 Vi the tolerance shall be 10 percent (K) and the resistance value shali be 1.0, 1.5, 2.2, 3.3, 4.7 or 6.8 ohms, (4) Power type: Specification JAN- R-26. Ft-98. JAN-R-29. 8.22.4 Wirwound rheostatt - Wire- wound

39、 power type rheostats shall be in ac- cordance with Specification JAN-R-22, 8.28 Sockets and tube shields.-Electron tube mkets and tube shields shall conform to the general requirements of Specification JAN-S-28 and where practicable shall be of the type designations given in that speci- flcaton, Wh

40、ere practicable, other plug-in psrtis hall also conform to the foregoing requirementctm procedure-for nau determined in quantity and number from the bid request or contract, individu- ally in accordance with the applicable provi- sions of Specification MIL-P-7. 2or ,. s 5.1.2.8 Spare pa shutter test

41、ing masks ; light shade, and lens adapter, determined in number and quantities from the bid request or contract, within the appropriate compartment of the shutter speed tester. Ell all voids with flexi- ble corrugated paper to prevent movement. Close door and secure fastenings. Place the shutter tes

42、ting scales in front of the cathode ray tube and hold in place with the retaining spring. Cushion each transit case, holding the shutter speed tester, on all surfaces with cells or pads fabricated of corrugated fiber- board, conforming to Specification 19-10 and designed to absorb the shock of impac

43、t nor- mally encountered in handling and transit. Place each cushioned item together with the required amount of desiccant as prescribed in MLP-116, within a close-fitting suitable style corrugated fiberboard box, having a minimum Mullen test strength of 276 pounds. Seal entire closure with gummed k

44、raft tape conforming to Specification UU-T-111. Blunt all corners of the box. Place the boxed item within a water-vaporproof barrier, qualified for class A application in accordance with the requirements of Specification ML-B- 131. Heat seal closure. Place the moisture- vaporproofed item within a cl

45、ose-fitting euit- able style and grade fiberboard box confom- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ing to sensitive tape, confomiing to Specifi- cation JAN-P-127. 5.2 Parking. 5.2.1 For domest& shipment.-The shutter speed tester packaged a

46、s specified in 6.1.1, shall be packed in substantial containers of the type, size, and kind commonly used for the purpose, in such a manner as to insure acceptance at and safe delivery to the desig- nated point by common or other carrier at the lowest rate. For Air Force use the shut- ter speed test

47、er shall be packed in boxes con- forming to Specification NN-B-601 or NN- B-621. 5.2.2 For export shipment. - Place the shutter speed tester packaged as specified in 5.1.2.6 and consolidated package in 5.1.2.4 within a wood cleated plywood, nailed wood or wire bound wood box conforming to he require

48、ments of Specification JAN-P-106, JAN-P-106 and MIGB-107 respectively. Fabricate the boxes to fit contents snugly. The approximate gross weight of any exte- rior shipping container shall not exceed 150 pounds. Place technical manual packaged as specified in 6.1.2.1 between the packaged item and lid

49、of the shipping container. Close and strap the shipping container as specified in the appendix of the applicable box specifica- tion. (Shipments consigned to depots shall not require strapping.) 5.3 Marking for shipment.-Interior pack- ages and exterior shipping containers shall be marked in accordance with applicable pro- visions of MIGSTD-129. 6. NOTES 6.1 Intended we.-The Test Sets, Shutter Speed (Camera Ts-703 ( ) /UF) are intended for use in