NAVY MIL-T-19244-1955 TRUCK HAND 2-WHEEL COMBINATION TRUCK AND DRAIN RACK《双轮组合货车及排水架手动卡车》.pdf

1、._ MIL-T-19244 (34 ) - 18 November 1955 MILITARY SPECIFICATION TRUCK, HAND, 2 WHEEL, COMBINATION TRUCK AND DRAIN RACK 1. SCOPE 1.1 Scope. -This specification covers combination barrel or drum trucks and drain racks, equipped with steel wheels and removable double handles, Combination trucks and drai

2、n racks are for use in transporting or draining drums or barrels of liquid chemicals or petroleum products where rugged design is required to insure safe, efficient, and economical operation under extended service conditions. 1. 2 Classification, -Combination trucks and drain racks shall be of the f

3、ollowing type, as specified in the contract or order: Type-Truck, hand, 2 wheel, combination truck and rack, drain, 55 gallon drum and barrel, double handle, 1 drum capacity, all metal construction, approximate weight 90 pounds. 2. APPLICABLE DOCUMENTS 2.1 The following specifications and standards,

4、 of the issue in effect on date of invitation for bids, form a part of this specification. SPECIFICATIONS FEDERAL QQ-P-416 - Plating, Cadmium (Electrodeposited) TT-(3-595 - Colors (for) Ready-Mixed Paints MILITARY MIL-P- 116 - Preservation, Methods of MIL-T-704 - Treatment and Painting of Materiel F

5、rED. SUP. CLASS 3920 1 f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-11133 -Crates, Wood, Slatted Style, Wirebound, Domestic STANDARDS MILITARY MIL-STD- 129 - Marking for Shipment and Storage (Copies of specifications and standards required

6、 by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the Contracting Officer. ) 2.2 Other publications, -The following publications, of the issue in effect on date of invitation for bids, form a part of this specification,

7、 CONSOLIDATED CLASSIFICATION COMMITTEE PUBLICATION Consolidated Freight Classification Rules (Application for copies of the above publication should be addressed to the Consolidated Classification Committee, 202 Chicago Union Station, Chicago 6 , Illinois, ) 3. REQUIREMENTS 3.1 General. -Combination

8、 trucks and drain racks covered by this speci- fication shall be complete and ready for operation when delivered. tion trucks and drain racks shall be constructed and equipped to meet all re- quirements specified herein, as well as all other referenced federal and mili- tary specifications and stand

9、ards. Combina- 3. 1. 1 Preproduction sample, -In all respects not specifically covered by this specification, the combination trucks and drain racks shall be equal to the preproduction sample. The design, structural, and operational characteristics of this sample also will be evaluated for acceptabi

10、lity from a standpoint of safety and efficiency in operation, and for conformance with generally accepted design practice, Unless otherwise specified, a preproduction sample shall be submitted for examination, inspection, and test, to determine compliance with all provisions of this specification. T

11、he first combination truck and drain rack produced under the terms of a contract, following notice of award, may be sub- mitted for approval as a preproduction sample, and approval shall be obtained 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-N

12、IL-T-172YY 37 W 7777906 0282607 5 i - MILT-19244 (a) prior to fabrication of subsequent items. prior to approval of the preproduction sample will be at the contractors risk and such additional items are subject to rejection in the event they fail to.meet the requirements of this specification. The p

13、reproduction sample combination truck and drain rack, if conforming to this speci- fication, will be used as a measurement guide for all combination trucks and drain racks subsequently manufactured for a given contract under this specification, and will be presented for inspection as the last unit f

14、or de1iver.y under the contract. Examination and testing, wherever practicable, will be conducted at the manufacturers plant by a represent- ative of the Contracting Officer and the delivery schedule, under the terms of the contract, will be automatically extended in an amount equal to, but not exce

15、eding the time required for such testing and examination. time for testing is estimated at less than 15 days, Fabrication of additional items The 3. 1. 2 Material. -Materials shall be as specified herein. Material not definitely specified may be manufacturer 1s normal commercial product, but shall m

16、eet test requirements specified in Section 4, commercial product“ shall be interpreted to mean an item producted by a manufacturer normally engaged in commercial production of the item(s) covered by this specification. The Government reserves the right to re- quire any bidder, who proposes to furnis

17、h other than a “normal commer- cial product“ to submit, prior to and as a condition precedent to the award of any contract, detailed engineering drawings of those parts he proposes to furnish in lieu thereof for approval of the Contracting Officer, “Normal 3.2 Structure 3.2.1 General, -The combinati

18、on trucks and drain racks shall be fabricated in accordance with the design and construction characteristics as specified in this specification and Figure 1. Combination trucks and drain racks shall consist of structural steel frame, cross braces, nose pieces, pipe handle, axle, and wheels. The fram

19、e, related structures, and all their joints shall provide a rigid unit structure. Completed com- bination trucks and drain racks shall be capable of withstanding, without permanent deformation, stresses induced by capacity loads and tests as specified in Section 4. 3.2.2 Frame. -The frame shall be f

20、abricated from commercial grade, structural steel angles and black steel pipe, as shown in Figure I. The frame and cross braces shall be made from 1 112 by 1 1/2 by 3/16 inch angles. Angles forming each side shall be notched, bent, 3 Provided by IHSNot for ResaleNo reproduction or networking permitt

21、ed without license from IHS-,-,-MIL-T-19244 37 977770b 0282608 7 ._- - MIL-T-l9244( S and bent down at an angle of 26 112 degrees from the horizontal, with a radius of 3 inches, 42 inches above the lower end. be joined by a cross brace, of 3/4 inch diameter black steel pipe, butt welded to each upri

22、ght, and a rest, of 1/4 by 1 1/2 inch hot rolled flat steel, bent to an inside radius of 12 inches and butt welded to each up- right. Centerline of the cross brace shall be 29 1/2 inches above the lower end of the handle. lower end of the handle. rights with their tops 19 5/8 inches above the lower

23、end of the handle. Fingers shall be set normal to the rest and centered on the uprights. Fin- gers shall be made from 1/4 by 4 by 4 inch, commercial grade, hot rolled flat steel. After handles have been fabricated, they shall be inserted into the pipe supports in the combination truck and drain rack

24、 and a 3/16 inch diameter hole shall be drilled through pipe supports, handles, and frame. To provide handle adjustment, 2 additional holes, 3/16 inch diameter on 1 inch centers, shall be drilled through each handle upright parallel to the first hole, handles in pipe supports during use. Uprights sh

25、all Top of the rest shall be 19 5/8 inches above the There shall be 2 fingers, butt welded to the up- Two, 118 by 1 inch cofer pins shall be provided to reain 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-19ZLILI 39 7997706 0282609 7 M - -

26、3.2.5 Axles and spacers. -Each combination truck and drain rack shall be provided with a 3/4 inch diameter, cold rolled steel axle, 17 inches long, and a 3/4 inch diameter, black steel spacer or sleeve, of a length sufficient to retain the wheels approximately 11 3/8 inches apart on centers, Axles,

27、and frame legs adjacent to them, shall have 3/16 inch diameter holes drilled in them to accommodate 1/8 inch diameter cotter pins. 3.2.6 Wheels. -Each combination truck and drain rack shall be pro- vided with two, 8 inch diameter by 2 inch tread, one piece, semi-steel wheels, equipped with commercia

28、l grade roller bearings. Roller bear - ings shall be of the size required for the application, and shall meet all test requirements in Section 4. seals and standard pressure lubrication fittings, Wheels shall be provided with grease 3. 3 Accessories. -Unless otherwise specified, no accessories shall

29、 be required. 3.4 Performance 3.4.1 Maximum load. -The combination truck and drain rack shall show no permanent deformation or failure following a static test under 200 percent of rated load, or 1,800 pounds, for a period of 1 hour. 3.5 Other requirements 3.5. 1 Bearings. -Bearing load capacity, inc

30、luding applicable safety factors, as rated by the bearing manufacturer, shall be equal to or greater than maximum bearing loading under normal truck and drain rack operation, 3.5.2 Grease fittings. -Grease fittings shall conform to the manu- facturers normal commercial practice, 3.5. 3 Steel fabrica

31、tion. -All edges shall be smooth, rounded, and free from burrs or jagged edges, 3.5.4 Welds, -Welded joints shall be sound; smooth; free from pits, holes, fissures, and rough projecting edges; and shall be thoroughly fused to the base metal. All joints shall be welded with 3/16 inch fillet welds aro

32、und their entire periphery. 3.5.5 Bolts and nuts. -All bolts, cap screws, and nuts shall be pro- vided with lock washers or other locking devices and shau be tightly 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-19244 39 9 999990b 022610 5

33、9 KIL-T-192 however, th? Government reserves the right to use additional information It is to be understood 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILT-19244 (S by approval of the above mentioned samples for a particular contract or order,

34、 the duly authorized agent thereby assumed responsibility to the Govcrnment for purchase .of items represented but in no way assumes any part of the contractor Is responsibility as to design or .satisfactory performance thereof for the purpose intended. If for any reason the equipment fails to meet

35、specification requirements, although its use has been tentatively sanctioned.by the duly authorized agent, such fact does not relieve the 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-contractor of responsibility to correct defects and make such

36、changes as may be necessary to meet specification requirements, without additional cost to the Government. S. PREPAiLATION FOR DELIVERY I 5.1 Preservation 5. 1.1 Domestic shipment (immediate use), -Cleaning and preser- vation shall be in accordance with manufacturer 1s standard practice, 5.1.2 Domes

37、tic shipment (storage) or overseas shipment, -Clean- ing and preservation shall be in accordance with Specification MIL-P- 116 as applicable. All unpainted surfaces subject to corrosion shall be coated with type P-1 preservative compound, excess with manufacturers recommended lubricant, Bearings sha

38、ll be lubricated to 5.2 Packing 5. 2. 1 Domestic shipment (immediate use). -The truck, packaged as described in 5.1.1, shall be packed in a manner to insure carrier accept- ance and safe delivery at destination. with Consolidated Freight Classification Rules or other carrier regulations as applicabl

39、e to the mode of transportation, Containers shall be in accordance 5. 2. 2 For domestic shipment (storage) or overseas shipment. - Unless otherwise specified, trucks preserved as specified in 5. 1.2, shall be individually packed in a style 2 wirebound wood crate conform- ing to Specification MIL-C-1

40、1133 and appendix thereto, be removed from the truck and secured to the crate or frame of truck so as to conserve the greatest amount of cube. Handles shall 5.3 Marking. -In addition to any special marking required by the contract or order, shipments shall be marked in accordance with Military Stand

41、ard MIL-STD - 12 9, 6. NOTES 6. 1 Intended use. -Combination truck and drain racKs described herein are intended for carrying barrels or drums, whose gross weight does not exceed 900 pounds, for short distances where powered mate- rials handling equipment is not available. emptying barrels and drums

42、 at their points of use, They also are intended for 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-L44 39 9999906 0282633 O I - _- VJL-T-19244 (su i 6. 2 Ordering data. -Procurement documents should specify the following: (a) Title, number,

43、 and date of this specification (b) Whether preproduction sample is required. (See 3. 1. 1) (c) Whether accessories are required. (See 3. 3) (d) Additional requirements not listed in specifications, (See 3.5.9) (e) General inspection procedures required, (See 4.2. i) (f ) Type of preservation, packi

44、ng, and packaging required. (See 5) (g) Special markings required in addition to MIL-STD-129. (See 5. 3) 6. 3 Guaranty. -Invitation for bids and contracts or orders shou i specify the following guaranty clause, except in those instances where it is determined that the inclusion of the guaranty claus

45、e would not be to the best interest of the Government, a. The contractor guarantees that at the time of delivery thereof the article provided for under this contract will be free from any defects in material, or faulty workmanship, or improper design, and will conform to the requirements of this con

46、tract. If the Govern- ment discovers any such defects or nonconformance within a period of one year after delivery, it may require the contractor (i) to correct or replace (as designated by the Contracting Officer) the defective or non- conforming articles or part thereof; or (2) to repay such porti

47、on of the contract price as is equitable in the circumstances. Notice of the defect or nonconformance shall be given by the Government within a reasonable time after delivery thereof. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b. If required b

48、y the Government to correct or replace the de- fective or nonconforming article or part thereof, the contractor shall with all possible speed make such correction or replacement. correction or replacement requires transportation of the article or part thereof, shipping costs, not exceeding usual cha

49、rges from truck location within the Continental United States or from the nearest designated port of embarkation to the contractors plant and return shall be borne by the contractor; the Government shall bear all other shipping costs, This guaranty shall then continue as to corrected or replacing articles, or, if only parts of such articles are