NAVY MIL-T-24649 13-1994 TELEPHONE HARDWARE SOUND POWERED CABINET HANDSET《电话硬件 声能驱动亭 听筒》.pdf

1、RIL-T-24649/13 9999906 1979692 540 MIL-T-24649/13(SH) 10 June 1994 MILITARY SPECIFICATION SHEET TELEPHONE, HARDWARE, SOUND POWERED CABINET, HANDSET This specification is approved for use by the Naval Sea S stems Command, Department of the Navy and is available for use gy all Departments and Agencies

2、 of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of the following specification listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) specified in the solicita

3、tion: MIL-T-24649 REQUIREMENTS : Dripproof (see 3.3.6) not required Splashproof (see 3.3.7) not required Insulation resistance (see 3.3.9) not required Talk demonstration (see 3.3.10) not required Identification plate (see 3.4.3) not required Information plate (see 3.4.4) not required Switches (see

4、3.4.6) not required Construction. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. AMSC N/A All dimensions unless otherwise specified are in mm. Tolerances, unless otherwise specified shall be plus or minus .127 mm. All sharp edges or corners exposed to touch shall be slightly rounded. Enclosures with a wall thicknes

5、s equal to or greater than 4.775 mm shall be provided with a cable entrance plate on the bottom of the enclosure. Cable entrance plates shall preserve the degree of enclosure specified, Space shall be provided inside the enclosure so that ships wiring will not be crushed or distorted when the enclos

6、ure is mounted and assembled. Screw threads for all threaded securing devices shall conform to FED-STD-H28. The thread shall be right handed, of the course thread series. Threads in aluminum alloys shall not be used. Through bolts shall be used whenever practical. Inserts shall be provided where scr

7、ews or bolts must be removed for maintenance. Threads shall not be employed in plastic parts without the use of suitable threaded metallic inserts. Castings, if applicable, shall be free of cold shots, blow holes or any other imperfections that may affect strength in any way. All surfaces of casting

8、s shall have all fins and burrs removed. Sand surfaces shall be disturbed as little as possible. Flash shall be removed and the width of the flash edges made thereby shall be no greater than 7.874 mm. Flash edges shall then be buffed smooth. 1 of 7 FSC 5935 DISTRIBUTION STATEMENT A. Approved for pub

9、lic release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-24649/L3 m 7Ob I1979693 487 m MIL-T-24649/13(SH) 11. No deviation in details, dimensions, size and type as shown on the applicable standard will be permitte

10、d, unless approved by the Naval Sea Systems Command (NAVSEA). All loose parts required for installation or operation shall be provided in a suitable cloth or plastic bag and packaged with the assembly. 12. Preparing activity: Navy - SH (Project 5935-N457-13) t I DENT IF ICATIOt PLATE I I I I I 1 I I

11、 I I I I l I I 4 DRILL 2 HOLEST L-4.-J - 57 IDENTIFICATION PLATE SOUND POWERED JACK. H-27A cabinet. front view. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A0 MIL-T-2Yb47/13 = 9997906 1777bq 313 m 133 133 t I il I II -R 10 -R 13 -R 22 DEEP DO N

12、OT 6.4 DRILL AT ASSEMBLY WITH BOX AND AND REAM FOR SMOOTH WWKINC FIT WITH HINGE PIN 2 HUES I I I I I I I I I I I I I I I I I I I 1 I I I I I I I I 1 I I c- I ; ,-: FIGURE 2. Cover. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-362 UIL-T-24649/23

13、9999906 2979695 25T = 333 133 m 1 I 49 -4 . -. 30 FIGURE 3. W. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-24649/13 7777Rb 397bb 196 = p-18- U 1 -STUFFING TUBE MIL-S-19622 WO-24 R.H. MACHINE SCREW - 0 UM LONG d SHAKEPROOF WASHER FOR #i0 I

14、 SCREW TUFFING TUBE WASHER 1.6 X 9.5 U.D. 6-32 R.H. YCH SCREW 9.5 LONG STUFFING TUBE SIDE VIEW FIGURE 4. Cabinet. inside view, cover removed. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RE TA G WO-24 R.H. MACH SCR 6-32 R.H. MACH SC PIN 2.4 MM D

15、IA -32 R.H. MACH SCR MM LONG b SHAKEPROOF ASHER FOR ?# SCR -32 R.H. MACH SCR 3 MM LONG b SHAKEPROOF ASHER FOR SCR STUFFING TUBE I MIL-S-19622 FIGURE 5. Bottom view. cover removed. SOUND POWERED JACK. H-27A k 110.3. .a ,A I 7 FIGURE 6. Top plate 6 Provided by IHSNot for ResaleNo reproduction or netwo

16、rking permitted without license from IHS-,-,-p309Y 9.5-16 NC-2 P TO MAVE PRESS FIT IN BOX PAD COVER, HOLD-DOWN O TB2 BLK R*NG7 r WHT OTE1 TIP - JACK H-25A WIRING DIAGRAM #lo-24 NC C-2- NC-2 I 39.7 I A I R 3.2 w STUD 74r 6 95 I HINGE PIN FIGURE 7. Details. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-