NAVY MIL-T-81311 A-1980 TRAILER AIR LAUNCHED WEAPONS ROUGH TERRAIN A M324-4A《 A M324-4A崎岖地形空中发射武器和拖车》.pdf

1、7 September 1965 MILITARY SPECIFICATION TRAILER, AIR LAUNCHED WEAPONS, ROUGH TERRAIN, A/M32K-4A This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agcncies of the Department of Defense. 1. SCOPE o 1.1 Scope

2、. - This specification establishes the requirements for the procurement of one type of flat bed, pneumatic tired, rough terrain trailer for air launched weapons. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a

3、part of this specification to the extent specified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILITARY (continued) MIL-M-8090 MIL-C-16173 MIL-G-23827 STANDARDS MILITARY MIL-STD-129 MIL-STD-810 DRAWINGS Mobility Requirements, Ground Suppo

4、rt Equipment General Specification for, Corrosion Preventive Compound, Solvent Cutback, Cold-Application. Grease, Aircraft and Instrument, Gear and Actuator Screw. O Marking for Shipment and Storage. Environmental Test Methods. NAVAL AIR SYSTEMS COMWWD Data List 67A219J1 Rough Terrain A/M 32K-4A Tra

5、iler Assembly (And all documents listed thereon). (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1

6、First article. When specified (see 6.2) the contractor shall furnish one sample unit far first article inspection and approval (see 4.2 and 6.2). 3.2 Construction. The trailer shall be manufactured in strict accordance with Naval Air Systems Command Data List DL67ASE9Jl and all documents listed ther

7、eon. 3.2 Performance Characteristics. The trailer covered by this specification shall meet the following performance characteristics. 3.3.1 Bed - The bed of the trailer shall be furnished with a non- skid surface in accordance with applicable drawings. 2 Provided by IHSNot for ResaleNo reproduction

8、or networking permitted without license from IHS-,-,-I When the cradle tie-down fittings described in 3.3.2 the trailer shall be free of any obstructions or protuberances. are removed, the bed of 3.3.2 Cradle tie-down fittings. - As shown on applicable drawngs, 12 cradle tie-down fittings shall be s

9、upplied with each trailer. These mechanica1,devices shall slid$ in the tracks provided in the trailer bed and are designed to hold cetan weapons cradles rigidly to the bed. 3.3.3 Brakes. 3.3.3.1 Service. - As shown on applicable drawings, air over hydraulic brakes shall be placed on the two rear whe

10、els of the trailer. Power is supplied by the prime mover. 3.3.2 Parking. - Mechanical parking brakes, as shown on appli-cable .drawings shall be utilized on the trailer. 3.3.4 Suspension. - As shown on applicable drawings, suspension is of the indepgndeptly sprung type with one multiple leaf spring

11、at each wheel. Each axle shall be provided with bump stops to insure that maximum deflection to stop is three inches. 3.3.5 Cramping stops. - Stops shall be furnished on the trailer chassis to restrict the cramping angle to a maximum of 40 degrees each side of center. 3.4 Mobility. - Trailers suppli

12、ed under this specification shall be capable of meeting, without damage, the- requirements listed below. In the event any conflict arises between the aformentioned specificat-ion and this document, the requirements herein stated shall apply. Requirement Test Paragraph (a) Towing loaded trailer: ,. (

13、1) on improved concrete between 35 and 45 mph for 50 miles. 4.4.2 (2) on improved gravel at 25 mph for 25 miles. 4.4.3 (3) across open fields and broken terrain at 5 mph for 25 miles. 4.4.4 (4) through figure eights at eight mph and demonstrating turning radius of not greater than 15 ft. 4.4.5 i 3 3

14、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-8 1311A(AS) Requirement * (5) across 20 percent grade five times in each directio (b) Braking loaded Trailer: (i) on 20 percent grade from 20 mph. within 30 ft. (2) on levei concrete from 20 mph

15、within 30 ft. (3) skidding wheels when towed with parking brakes applied. (4) parking on 20 percent grade. with trailer facing iiphill (5) parking 011.20 percent grade with trailer facing downhill (6) brakes lock when towing force removed. (c) Drawbar pull and static resistance: (i) Trailer shall ro

16、ll before 225 pounds is applied through drawbar. Test Paragraph 4.4.6 4.4.7.1 4.4.7.2 4.3.6 4.4.7.3.1 4.4.7.3.2 4.3.6 4.3.5 3.5 Environmental requirements. - Trailers supplied under this cpeci- I ation shall be capable of meeting, without damage, the following environmental criteria: I High temperat

17、ure - 160F for eight hours. 4.5.1 I for eight hours. 4.5.2 I Sand and dust - Method 510.1, Procedure 1 of MIL-STD-810. 4.5.4 Fording - 30 minutes immersion in water. 4.5.5 4 I a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*. 1 .- -. -. 4.2 Classi

18、fication of inspections. - The examination and testing of trailers supplied under this specification shall be as follows: . 1. - I. II i I_ _. *. 4.2.1 First article inspection - The first article sample and its related components shall be subjected to all examinations and tests of this specificatio

19、n. Unless otherwise specified, these exami- nations and tests shall be performed by the contractor 4.2.2 Quality conformance inspection. - Examination and testing of each trailer for acceptance shall consist of those procedures , specified;.n k.3, . 43 4.3.1 Inspection conditions,. -.Unlegs otherwis

20、e specified-, , Quality cconfQrmance eyamination and testing. : i : .- - i, .* trailers shall be tested under the following conditions: i .( a Temp e rat ur e - 77 + 18 degrees EahFenheit Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(b) ?Humidity

21、(c) Barometric Pressure i s CI .4.3.2 Examination - The trailer shal-1, be Ifnopecte to-r-ditetmine compliance with the requirements specified herein with .-tespec.t? to . = t-. cerein weapo :cradles to determine tpat .the? .fittfngs?-Qill i .in faet; r? . . wheh the pneumatic line fro type vehicle;

22、 The electrical. cable and pneumatic hoses of the trailer shal No adjustment or sedc2ng tof?arty typ shall be performed .I .c :i: ._ . :I :-,-,. . :. NOTE: - on the trailer during any of the following road tests. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

23、from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-L3LLA 17 W 777770b 0204503 T MIL-T-8131 lA(AS) 4,4.7.3.2 The loaded trailer shall be towed to a position where the front of the trailer is facing down a 20 percent (11.3 degrees) grad

24、e and the parking brakes applied. The towing forces shall be re- moved and the trailer shall hold its position for a minimum time of 30 minutes. 4.4.8 Examination. - Upon completion of the foregoing tests, the trailer shall be examined. The trailer shall not have suffered any damage which is conside

25、red sufficient to preclude its meeting any per- formance or operational requirements of this specification. 4.5 Environmental testing. Unless otherwise specified in the contract or order, sample trailers supplied as specified. in 4.2.1 shall be subjected to the following environmental gesting. 4.5.1

26、 High temperature. - The trailer shall be loaded with 8,000 pounds as described in 4.4.1 and exposed to an ambient temperature of 160 degrees Fahrenheit for eight hours. At the end of the eight hour exposure and while still at 160 degrees, the trailer shall be rolled to assure function of moving par

27、ts and brakes. The temperature of the room shall be returned to 80 +lo degrees Fahrenheit and the trailer examined. 4.5.2 Low temperature. - The loaded trailer shall be exposed to an ambient temperature of minus 65 degrees Fahrenheit for eight hours. At the end of the eight hours exposure and while

28、still minus 65 degrees, the trailer shall be rolled to assure function of moving parts and brakes. The temperature of the room shall be returned to 80 kl0 degrees Fahrenheit and the trailer examined. 4.5.3 Humidity. The trailer shall be unloaded and subjected to the Humidity Test of Method 507.1., P

29、rocedure I, MIL-STD-810. At the conclusion of the ten cycles, the trailer shall be returned to a normal humidity environment and examined. The trailer shall be towed a short distance to assure function of moving parts and brakes. 4.5.4 Sand and dust. - The loaded trailer shall be subjected to the Sa

30、nd and Dust Test of Method 510.1, Procedure I, MIL-STD-810. The air velocity shall be between 100 and 500 feet per minute. At the conclusion of the test, the trailer shall be returned to a normal en- vironment and examined. The trailer shall be towed a short.distance.to assure function of moving par

31、ts and brakes. 4.5.5 Fording. - The trailer, loaded as described in 4.4.1 shall be towed into a 30 inch deep fording tank. After 30 minutes immersion, the trailer shall be removed from the tank and attached to a prime mover. The trailer shall then be towed at 15 miles per hour and the brakes applied

32、. The braking characteristics shall be noted. 5. PACKAGING 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 .- i 5.1 Preservation packaging. - Preservation packaging shall be either Level A or Level C, as specified (see 6.2). 5.1.1 Level A (mobile

33、). I 5.1.1.1 Cleaning and drying. - The trailer shall be cleaned and dried in accordance with MIL-P-116. Cleaning shall be accomplished in accordance with Procedure C-l. Drying shall be accomplished in ac- cordance with Procedure D-1 or D-4, or a combination of both. d o; 5. i. i. i 5.1.1.2.1 Unpain

34、ted bearing surfaces. All unpainted bearing surfaces shall be coated with grease conforming to MIL-G-23827, and wrapped with grease-proof barrier material conforming to MIL-B-121, Type II, Grade A, Class 2, secured in place with tape conforming to PPP-T-60. 5.1.1.2.2 Unpainted non-bearing surfaces,

35、All unpainted non- bearing surfaces shall be treated with preservative compound conforming Preservation application. 1. bo MIL-C-16173, Grade 1. axle shall be coated with grease conforming to MIL-G-23827. 5.1.1.2.4 Pneumatic system and cable ends. - Openings into the pneumatic system and the ends of

36、 electrical cables shall be covered with grease-proof barrier material conforming to MIL-B-121, Type II, Grade A, Class 2, secured with tape conforming to PPP-T-60. t I 5.1.1.2.5 Technical publications. - Any technical publications supplied with the trailer shall be packaged in accoydance with Metho

37、d IC-1 of MIL-P-116. 5.1.2 Level C (mobile). - The trailer shall be prepared for ship- ment in accordance with the suppliers standard commercial practice, in a manner acceptable to common carriers for safe transportation to point ri of destination at the lowest transportation rate for the commodity.

38、 This level is intended to provide adequate protection for immediate use domestic shipments, from supply source to the first receiving activity. 5.2 Marking. In addition to any special markings required by the contract or order, the basic trailer and any interior packages shall be marked in accordan

39、ce with MIL-STD-129. 6. N0,TES AND CONCLUDING MATERIAL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(a) Title, number, and date of this specification. (b) (c) Whether or not a first article sample is required. Number of Trailers which will. consti

40、tute the first sample. Information pertinent to the site of first article (see 4.2.1). B (d) (e) Whether or not test reports are required (see (f) Whether or not weapon cradles will be supplied for acceptance testing (see 4.3.3). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-