NAVY MIL-T-81546 A-1971 TEST STAND ACTUATOR LINEAR LOAD《线性负载致动器试验立场》.pdf

1、z c MIL-T-BL5LIbA LI9 H 7999706 025b5L4 O H -.: - MILITARY SPECIFICATION MIL T- 8 1 5 4 6 A (A S) 18 Fehrdary 1971 Superseding 21 July 1967 MIL T-81546 (AS) TEST STAND, ACTUATOR, LINEAR LOAD This specification has been approved by the Naval Air Systems Command, Department of the Navy. 1. SCOPE 1.1 T

2、his specification covers the requirements for a lined load, actuator, test ,- stand (herein referenced test unit). right, stationary, pneumatically powered test stands trol cabinets for use in performing operational tests This test unit is a onsisting of two up- bench type con- 2. APPLICABLE DOCUMEN

3、TS 2.1 Government documents normally furnish4 - The following documents, of the issue in effect on date of invitation for bids ogrequest for proposal, form a part of this specification to the extent specified herein. SPECIFIC A TIONS Federal W-C-596 GGG76 PPP- B- GO 1 PPP-B- 621 hlilitarp Connector,

4、 Plug, Electrical, Connector Receptacle, Electrical; Plates, Wall Electrical Gauge, Pressure and Vacuum, Dial Indicating, For Air, Steam, Oil, Water, Ammonia, and Chloro- Fluoro Hydrocarbon Gases Boxes, Wood, Cleated, Plywood Boxes, Wood, Nailed and Lock-Corner MIL-P-116 MIL- C- 50 1 5 Preservation,

5、 Methods of Connector Electric, AN Type F C-4920 G o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-BLSLlbA 49 m 9779906 0256535 2 m MIL-M-10304 AIIL-C-13924 Meters, Electrical, Indicating, Panel Type, Ruggedized Coating, Oxide, Black for Ferr

6、ous Metal STANDARDS Military MIL-STD-129 Marking for Shipment and Storage MILSTD-13 0 Identification Marking of U. S. Military Property BIIL-STD-143 Specifications and Standards, Order of Prece- dence for the Selection of .1245“, .1557“, . 18701, and .2495“ diameter for the mini unit, these dimensio

7、ns arehshing bore diameters and the matching pins are to be ground for a snug sliding fit. The pins are to have a 16 micro inch RMS finish and a life expectancy of 1,000,000 reversals. A steel carrying case shall be provided to house ali threaded bushings and attachment pins. The bushings shall be g

8、rouped as to size and identified by labeling in the kit. 3.7.1.5.2 Guide bushings - The outboard ends of the movable carriage are to be guided by precision linear ball bushings having multiple ball circulating tracks and having a coefficient of friction of . O02 - .004. i 3.7.1.6 Anchor device - To

9、be of steel fabricated so as to provide a means for attaching the actuator. The main fixture only shall have an adjustable anchor - beam of steel, A box-section adapter for mounting flange-type actuators capable of full-load capacity shall be provided for the main fixture. The adapter shall attach t

10、o the fixed beam. Beams or adapters to be removable from vertical up- rights and adjustable within full range. Universal adapters are to be provided so that a wide variety of actuator mounting can be accommodated. For the mini fixture the universal adapters shall be attached directly to the load fix

11、ture base. 3.7.2 Control console - i: 3 3.7.2.1 Control cabinets, general - Cabinets are to be of sheet metal and such design and construction as to withstand severe service. Maximum dimensions are to be 24“ wide (L to R) x 17“ deep (F to B) x 15“ high having a sloping front for instrument and contr

12、ol mounting. Cabinets are to be portable, enclosing all controls both pneumatic and electric and aifording means for providing service to test fixtures and a means for monitoring actuator performance under test. All interconnections, both pneumatic and electrical, between cabinets and test fixture a

13、re to be by removable hose and conductors fitted with end fithng of such design as to insure quick disconnect and insure operator safety. All indicating dials and controls are to be mounted on the cabinet sloping front and to be so positioned as to be convenient for reading and operation from the op

14、erators normal position. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-L54bA 47 777770b 025b520 b W All dials, gages, etc., are to be face mounted and top side access is to be pro- vided for maintenance of components requiring frequent serv

15、ice. Operating switches, indicator lights, etc. , may be mounted on straight portions of cabinet front and top. Recessed finger cavities are to be built-in to cabinet side to facilitate carrying . 3.7.2.2 Control cabinet, pneumatic - A metal cabinet detailed in 3.7.2.1 shall house all pneumatic cont

16、rol components, piping, gages, valves, etc., as are re- quired to conduct test operations. Quick disconnect fittings, for incoming air and air supply to test fixtures, are to be from rear of cabinet. The system must be capable of operation on 100 psig compressed air supply. Means are to be provided

17、for infinite regulation of delivered air over fit11 pressure range. The system must be designed so as to permit venting air presmre over a regulated setting while applying an aiding or opposing load. A three position control valve must be provided to select tension, compression or neutral position.

18、Regulating and control valves must hae sufficient flow and pressure capacities for continuous duty on 100 psig air supply. Regulation of air pressure must be maintained within 2 psi of set pressure under either aiding or opposing loading. An air filter and air line lubri- cator are to be included in

19、 the pneumatic circuit and be accessible for mainten- ance and inspection. A dial indicating gage for both tension and compression shall be located on output side of pressure regulator. All gages, pressure regu- lator operating knob and selector knob are to be mounted in the sloping face of the cont

20、rol cabinet and be convenient for the operator. 3.7.2.2.1 Gages - All pneumatic gages must have full range capacity and a built-in accuracy of 1/2 of 1 percent. Gages are to be a minimum of 6 inches in diameter and must have an external adjustment for calibration. Gages for both tension and compress

21、ion are to be face mounted within the cabinet sloping front. Gauge dials shall have color-coded scales to directly indicate load applied for either fixture over full range. Also, a psi scale shall be provided, 0-100 psi, for calibration. Gages shall conform to GG-G-76. 3.7.2.3 - Control cabinet, ele

22、ctric - - A metal cabinet detailed in 3.7.2. i shall be provided to house ,211 clectric control components, timer, meters, switches, circuit breakers, terminals, etc., as are required to conduct test operations. Connections between control cabinet and actuator under test are to be portable cords hav

23、ing ends suitable for connecting to binding post at control cabinet and open end leads at actuator. Each cabinet to be furnished with a total of twelve (12) leads (nine (9) for A. C. and three (3) for D. C. ) capable of delivering design capacity of system. Power for operation of the actuators is to

24、 be from external 7 , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-T-L54bA 47 7777906 0256523 I powor HOU rccs, tl:livcrcd to and monitorcci th rough thc (:on( rol diiict. powcr connections are to he by portable cords, roin mar o cabinet, ro

25、ccptncles and plug to he in accordance with W-C-596 and MIL-C-5015. Output power re- quirements are 110 Volt, single phase, 400 cycle, 10 amperes; 208 Volt, 3 phase, 400 cycle, 10 amperes; and 28 Volt, D. C., 20 amperes. Control circuit to oper- ate on 115 Bolt, single phase, 60 cycle service. Instr

26、umentation to include A. C. and D. C. volt meters and ammeters with selector switch to permit reading of total draw in any phase, timer, operational switches for forward and reverse operation, indicator lights, terminal binding post, voltage and phase selector switches, and all other components requ

27、ired for safe and efficient operation. All gages, instruments, switches, terminals, circuit breakers, indicator lights, etc. , are to be face mounted on cabinet front. Components not requiring visual readout may be mounted on straight portion of cabinet face or top. All instruments, switches, indica

28、tor lights, terminals, etc., are to be clearly labeled with rigid nameplates conforming to MIL-STD-130 and securely affixed in place or have the identification engraved or silk screened on the cabinet front panel in a relative position as applicable. The lettering is to be a minimum of 1/8“ high; an

29、d if en- graving is used, characters are to be filled with black enamel to insure visibility. All circuit breakers are to be of the reset type and to be available for reset with- out having to remove panels or other covers. Iiipiit 3.7.2.3.1 Power cable - The electrical control cabinet shall be furn

30、ished with a separate electrical supply cord for ench required external power source. Each cold shall be 10 fect long conforming to ANSI-C-1. Tho powcr cord shall he fit tcd vifi appliczble connector pliigs in :iccord:mcc with W-C-59j. The size md typc shall bc siiitriblc for thc rcquircd servicc. 3

31、.7.2.3.2 Power switch - A power ON-OFF switch shall be provided for both A. C. and D. C. sources. An indicator lamp shall be provided to indicate “POWER-ON1. 3.7.2.3.3 Circuit breaker - All electrical circuits must be protected by circuit breakers of adequate capacity to permit operation at full ran

32、ge of com- ponents. All circuit breakers mus be accessible from front of console, 3.7.2.3.4 Timer - Actual time of load test must be measured by means of an electric timer. Timer must be capable of automatic or manual operation or control by external switches. Timer to have a one second, 360“ sweep

33、with dial graduations in.01 second; a one minute (O-GO second) hand, 360“ sweep with dial graduations in one second; and a 0-15 minute totalizer in one minute graduations to be at least 3.5 inches in diameter and face mounted within the sloping face of the cabinet. Timer control circuit is to incorp

34、orate a electronic, solid state current sensing device to automatically start and stop timer consistent with current flow to the actuator and to be capable of operation in both the A. C. and D. C. modes, The sensor circuit shall activate the timer at any current draw between 150 miliamps and 20 amps

35、. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A MIL-T-BL54bA LI9 9999906 0256522 T m - _. MIL-T -81 5.46 ( AS) Response time shall be less than one milisecond. The timer is to be provided with a portable remote cord, atleast three feet long, wi

36、th start, stop, and reset buttons. 3.7.2.3.5 Instrumentation - Voltmeters and Ammeters, 2 1/2lf minimum diameter, shall be provided to monitor power consumption during test. Meter internal movements to be of ruggedized construction conforming to MIL-M-10304. Meters are to be face mounted on the slop

37、ing face of control cabinet. Phase selector switch is required for reading current flowing in any one branch of a three phase system. A.C. ammeters to be dual range having scale of 0-10 and 0-1. O amperes. D. C. ammeter to be dual range having scales of 0-20 and 0-2. O amperes. Range selector switch

38、 to be panel mounted with spring return momentary contact in low range position to prevent meter damage due to in-rush current at start-up . 3.7.2.3.6 Run-job switch - A three position switch shall be mounted on the panel to operate the item being tested. One position shall be spring-loaded for mome

39、ntary contact to be used to jog the actuator during Set-up and special testing. 3.7.2.3.7 Mode selector switch - A “Mode Selector Switch“ shall be provided to select automatic, manual, or auxiliary modes of operation of Actuator being tested and inter-related circuitry. This switch shall be so wired

40、 as to allow opera- tion of test actuator through timer remote cord. 3.7.3 Label plate - Each switch, gage, meter, indicator light, terminal, control device, etc., shall be labeled as to identify its function. Power outlets are to be identified as to characteristics. to cabinet, or the information m

41、ay be engraved or silk screened on the front panel in letters no less than 1/8“ high and filled with black enamel if engraving is used. Label plates are to be securely affixed 3.7.4 Accessories - One complete accessory set shall be installed on each test fixture, The accessory equipment shall consis

42、t of a scale indicator and an adjustable microswitch. This accessory equipment will permit accurate adjust- ment of mid-position and verification of full travel capability. It will allow simpli- fied calculations wherein actuator speed must be expressed in inches per second. The precision steel scal

43、e shall be mounted on one side of the test fixture. The scale shall be adjustable (to permit setting the %era“ reference point), and shall be equipped with two adjustable reference stops. A pointer shall be attached to the movable crosshead to allow the “stroke“ to be read directly in inches. The ad

44、justable microswitch shall be attached to the scale. The microswitch shall be furnished with leads and plugs to mate with the t1auxiliaryf7 terminals on the 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-T-8154bA Y9 9999906 0256523 I electrica

45、l console, and shall be actuated by the pointer on the movable crosshead. When in the “au;uiliaryll mode, circuitry within the console shall automatically stop the actuator and record time for any pre-determined intermediate actuator setting. Accessory equipment shall be mounted on the linear actuat

46、or test stand. 3.8 Color and finish - Load Fixture: All functional steel parts shall be finished black oxide in accordance with MIL-C-13924, Class 1. Non-functional parts may be painted grey enamel. Control Cabinet: All parts fabricated from ferrous metal not otherwise plated or protected, shall be

47、painted grey enamel. 3.9 Identification marking - A metal nameplate of reasonable size, per- manently marked in accordance with MIL-STD-130 shall be securely attached to each of the test stands and the control cabinets. 3.10 Workmanship - Workmanship shall be in accordance with the best commercial s

48、tandards All components and assemblies shall be free from burrs, rough surfaces, marred finish, broken, loose damaged or missing parts; and be capable of functioning satisfactorily when properly connected to an adequate power source. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection

49、- Unlcss otherwise specified in the con- tract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may utilize his own facilities or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the ins