NAVY MIL-T-81791-1970 TAPE TEXTILE NYLON LANDBASED ARRESTING GEAR 11 INCH《11英寸陆基拦阻装置尼龙织物带》.pdf

1、. e. L*-*Uriirp- r- 7 *7= - _ #- . -. f. . c . Weight, u!jces/yard .r (ma) g . -/ Breaking rength, pounds (min) - I/ *. - j - * C4r. - pen Place Jerked-In, Filling, Slough-Off, Slug . Kinks Knots icli slack End Iispick, Double Slub or Slag, Gout i .- -I . i . DESCRIPTION Rlultipe, less than i/2 :h i

2、n combined warp or ling directions or single )at or skip over more an 1/2 inch, but not ex- :ediiig 1 inch if in warp, * more than 1/4inch of ,e width but not exceeding inch, if in filling. learly visible opening etween adjoining picks, . r waipwise tension area ver part of the width re- ulting in v

3、isible light .nd heavy place. i clearly visible loop of lling pulled in at edges. lGre than 3 in any 9 linear inches. More than 1 knot in any 5 linear inches. One knot every 2 yards with un- trimined ends extending from surface of tape. TWO or more across the fidl width. Single across the fidl width

4、. Two or more in the same length, jerked in bemeen picks, or forming clearly visible loops on the sur- face. Nore than twice the thick- ness of the yarn (or ply, if plied). 13 CRITICAL MAJOR . x X X X Licensed by Information Handling Services_ -. ?41L-817% (tiiiic of nfanufacturc (i not thc samc as

5、contractor) - GEAR, 11-INCH In addition, each reel sliall hc marked or shipment in accordance with the NIL-STD-129. 5.2 Inspectioii of packaged roll of tape - 5.2.1 General -_ The method of packing and all material entering into the process sliall be subject to inspection by authorized Government In

6、spectors. When inspection is conducted at the contractorfs plant, it shall be conducted by the contractor under the supervision of the Inspector. I. h I - . . , _ 1. . ,. . r - .I , 4 i. -8 1 i i i I i ! I I I Licensed by Information Handling ServicesLicensed by Information Handling ServicesMIL-T -8

7、17% (AS) 5.2.2 Prcvious approval - Acceptance of approval o matcrial in course of packing shall in no case be construed as a guaranty of the acceptance of the finished package. 5.2.3 Examination of package - Each package shall be carefully exam- ined to determine conformance with the requirements of

8、 this specification. 5.2.4 Rejection and retest - Failure of any package to conform to any one of the requirements of this specification shall be cause for rejection. Packages which have been rejected may be reworked or replaced to correct the defects and resubmitted for accept8nce. Before resubmitt

9、ing, full particulars concerning pre- I vious rejection and the action taken to correct the defects found in the original shall be furnished the government quality assurance representative. 6. NOTES 6.1 Intended use - The nylon tape covered by this specification is intended for use in landbased airc

10、raft arresting gear. 6.2 lowing: Ordering data - Procurement documents should specify the fol- (a) Title, number and date of this specification. (b) Size. (c) Quantity desired. (d) Manufacturers identification. (e) Color required if other than specified in 3.3. (f) Length of roll required. t 1 (g) P

11、rovisions for deductions of defects (if any). (h) Responsibility for inspection records (see 4.1). Specify whether copies of records are to be furnished Government. . 6.3 For access to the standard sample, address the procuring activity issuing the invitation for bids, Custodian: Navy - AS 17 Preparing activity: DOD Project No. 8315-N139 Navy - AS :* :. Licensed by Information Handling Services