NAVY MIL-T-85284-1983 TEST SET ADAPTER GROUP OF-65 ASM《OF-65 ASM适配器组试验装置》.pdf

1、 MIL-T-85284 70 7979906 017404b T m 7 MIL-T-85284( AS) 20 July i983 MILITARY SPECIFICATION TEST SET, ADAPTER GROUP, OF-65/ASM This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of

2、 Defense. 1. SCOPE. 1.1 Scope. This specification establishes the requirements for manu- facture and acceptance of the Test Set Adapter Group OF-65/ASM critical item, referred to herein as the TSAG. 2. APPLICABLE DOCUMENTS. 2.1 Government documents. 2.1.1 Specifications and standards. Unless otherwi

3、se specified, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent specified herein. SPEC1 FICATIONS MI LI TARY MIL-T-183

4、03 Test Procedures; Preproduction, Acceptance, and Life for Aircraft Electronic Equipment, format for. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this docu- ment should be addressed to: Commanding Officer, Naval Air Engineering

5、 Center, Engineering Specifications and Standards Department (ESSD), Code 93, Lakehurst, NJ the self-addressed Standardization Document Improvement Pro- posal (DD Form 1426) appearing at the end of this document, or 08733, by using Provided by IHSNot for ResaleNo reproduction or networking permitted

6、 without license from IHS-,-,-MIL-T-21200 STANDARDS FEDERAL FED-STD-1 O2 MILITARY MIL-STD-108 MIL-STD-109 MI L-STD- 129 MIL-STD-130 MIL-STD-454 MIL-STD-81 O MIL-STD-831 MI L-STD- 1 695 MI L-STD-45662 Test Equipment for Use with Electronic and Electrical Equipment, General Specification for. Preserva

7、tion, Packaging, and Packing Levels. Definitions of and Basic Requirements for Enclosures for Electric and Electronic Equipment. Quality Assurance Terms and Definitions. Marking for Shipment and Storage. Identification Marking of U.S. Military Property. Standard General Requirements for Electronic E

8、quipment. - Test Methods. Preparation of. Working, Minimum Standards for. Environmental Test Reports, Environments, Cal i bration S s.tems Requirements. 2.1 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of thi

9、s specification to the extent specified herein, DOCUMENTS Naval Air Systems Command (Code Ident 30003) WS-6536 Procedures and Requirements for Preparation and Soldering of Electrical Connections. Federal Ca tal ogi ng Handbook H4 Federal Supply Code for Manufacturers, United States and Canada. 2 Pro

10、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE OF FEDERAL REGULATIONS (CFR) 49 CRF Parts 171-178 Transportation. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D.C. 20402.) N

11、AVAIR 16-50 BAC-2-1 3 Technical Manual, Computer Memory Loader- Verifier Test Set AN/ASM-607(V) (Series) AN/ASM-607A(V) (Series). 93555.) (Application for copies should be addressed to Commander (Code 3655) y Naval Weapons Center, China Lake, CA DRAW I NGS Naval Air Systems Command (Code Ident 30003

12、) 11 64AS616 11 64AS617 Test Requirements Document for Circuit Card Assembly Test Card. Test Requirements Specification for Circuit Card Assembly Test Card. 11 64AS222 Assembly, Adapter Groupy Test Set (Ul). (Copies of specifications, standards, drawings, and publications required by manufacturers i

13、n connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer . ) 2.1.3 Order of precedence. In the event of a conflict be-tween the text of this specification and the references cited herein, the text of this specificatio

14、n shall take precedence. 3. REQUIREMENTS. 3.1 Item description. The TSAG is a lightweight portable adapter kit used to convert an AN/ASM-607( V) Computer Memory Loader-Veri fier (MLV) Test Set into a configuration to test another MLV. The software routines required to perform the executive functions

15、 of the MLV are stored in the programmable read only memory in the MLV. The software routines required to perform the TSAG function are stored in the tape transport unit in the MLV and loaded into the random access memory in the MLV as required. 3 Provided by IHSNot for ResaleNo reproduction or netw

16、orking permitted without license from IHS-,-,-MIL-T-5284 70 m 4977706 017q044 5 W 3.1.1 Government furnished property. When specified in the contract or purchase order, the Government will furnish two MLVs and one copy of NAVAIR 16-50 BAC 2-13 (see 6.2.1). 3.1.2 First article. When specified, a samp

17、le shall be subjected to first article inspection (see 4.4 and 6.3). 3.2 Characteristics. 3.2.1 Performance. 3.2.1.1 Interface pin definition. The function aiid location of each signal on-the output of the TSAG Al test card shall be as specified in Appendix A. 3.2.1.2 Functional requirements. The fu

18、nctional requirements for the TSAG Al test card shall be in accordance with the command address word as specified in Appendix B and on Drawings 1164AS616 and 1164AS617. 3.2.1.3 Individual acceptance tests. Individual acceptance tests shall be performed on all TSAGs in accordance with 4.6.2. 3.3 Desi

19、gn and construction. The design, construction, materials, and finish of the TSAG shall conform to the requirements specified herein and as Specified in MIL-T-21200. If not specified in MIL-T-21200, the details of design, construction, materials, and finish shall be such as to ascertain that the TSAG

20、 will meet the requirements specified herein. Acceptance or approval of any such details shall not be construed as a guarantee of acceptance of the finished TSAG. 3.3.1 Production drawings. The TSAG shall be fabricated and assembled i.n accordance with the drawings, parts lists, and other documents

21、listed on Drawing 11 64AS222. 3.3.2 Interchangeability. The equipment shall meet the applicable interchangeability requirements as specified in MIL-T-21200, 3.3-.3 Materials. All materials used in the construction of the TSAG shall be in accordance with MIL-STD-454, Requirement 3, Flammable Material

22、s; Requirement 4, Fungus-Inert Materials; Requirement 15, Ferrous Alloys, Corrosion Resistance; and Requirement 16, Dissimilar Metals. 3.3.4 Standards of manufacture. The TSAG shall be manufactured, in- spected, and tested under conditions and procedures as specified herein. 4 Provided by IHSNot for

23、 ResaleNo reproduction or networking permitted without license from IHS-,-,- - - MIL-T-S24 70 m 9999906 0174050 1 M 3.3.4.1 Special working environment. The contractor shall provide adequate facilities for the fabrication, assembly, and inspection of the item to be manufactured in accordance with th

24、is specification. Unless otherwise specified in the contract or purchase order (see 6.2.1), the minimum standards for working environments of MIL-STD-1695 shall apply to the facility where final assembly, test, and delivery of the TSAG is accomplished. 3.3.4.2 Soldering. Procedures for the preparati

25、on and soldering of electrical connections shall be in accordance with WS-6536. 3.4 Environmental requirements. 3.4.1 High temperature. The TSAG shall show no detrimental effects and shall meet the performance requirements of 3.2.1 afher exposure to a high temperature environment of +55 degrees Cels

26、ius ( C) for a period of 48 hours minimum (see 4.6.3.1). 3.4.2 Low temperature. The TSAG shall show no detrimental effects and shall meet the performance requigements of 3.2.1 after exposure to a low temperature environment of -40 C for a period of 24 hours minimum (see 4.6.3.2). 3.4.3 Shock. The TS

27、AG shall show no detrimental effects and shall meet the performance requirements of 3.2.1 after subjection to the shock tests of MIL-STD-810 (see 4.6.3.3). 3.4.4 Watertight. The TSAG shall show no detrimental effects and shall meet the performance requirements of 3.2.1 after exposure to the watertig

28、ht tests of MIL-STD-108 (see 4.6.3.4). meet the performance requirements of 3.2.1 following exposure to a salt fog environment (see 4.6.3.5). 3.4.5 Salt fog. The TSAG shall show no detrimental effects and shall 3.4.6 Dust (fine sand). The TSAG shall show no and shall meet the performance requirement

29、s of 3.2. to a dust (fine sand) environment (see 4.6.3.6). 3.5. Identification and marking. The TSAG shall Marking sha marked in accordance with MIL-STD-130. be limited to, the following: etrimental fol 1 owi ng be identif 1 include, effects expo sur e ed and but not 5 Provided by IHSNot for ResaleN

30、o reproduction or networking permitted without license from IHS-,-,-MIL-T-85284 70 = 7777706 CIL74051 3 m MI L- T- 85 284 ( AS ) a. The number and date of this specification. b. NAVAIR code identification number, 30003. c. Manufacturers name and symbol or code identification from Federal Cataloging

31、Handbook H4. d. A unique serial number. 3.6 Workmanship. The TSAG, including all parts and accessories, shall be constructed and finished in a manner that will ensure com- pliance with all the requirements of this specification and the re- ferenced drawings. Fabrication and assembly practices shall

32、be in accordance with MIL-STD-454, Requirement 9. 4. QUALITY ASSURANCE PROVISIONS. 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order (see 6.2.1 ) , the contractor is responsible for the performance of all inspection requirements as specified herein. Exce

33、pt as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections

34、set forth in this specification where such inspections are deemed necessary to ensure that supplies and services conform to prescribed requirements. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4). b. Qu

35、ality conformance inspection (see 4.5). 4.3 Test conditions. 4.3.1 Test equipment. 4.3.1.1 Calibration and maintenance. Unless 0th rwise specified herein, all test equipment shall be calibrated and maintained in accordance with MIL-STD-45662. 4.3.1.2 Test equipment accuracy. All test equipment used

36、in the performance of the specified electrical tests shall have an accuracy greater than one-fifth the tolerance for the variable to be measured. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-85284( AS) 4.3.1.3 Test facility environment. Un

37、less otherwise specified herein, tests shall be performed under the following conditions: a. Tempera ture : Ambient , between +18OC and +35OC. b. Altitude: Elevation of test facility. c. Relative humidity: Ambient (shall be not greater than 95 percent relative. ) 4.3.2 Test documentation. 4.3.2.1 Te

38、st rocedures. When specified in the contract or purchase order (see 6.2.1 + detailed test procedures conforming to the applicable requirements of this specification and MIL-T-18303 shall be prepared for procuring activity review prior to commencement of testing (see 6.2.2). 4.3.2.2 Test plan. When s

39、pecified in the contract or purchase order (see 6.2.1), a detailed test plan shall be prepared for procuring activity review prior to commencement of testing (see 6.2.2). 4.3.2.3 Test re Orts. When specified in the contract or purchase order (see -+- 6.2.1 test reports shall be prepared in accordanc

40、e with MIL-STD-831 (see 6.2.2). The reports shall contain the quantitative results of each examination, test, or measurement specified. 4.3.2.4 Certification. The contractor shall have available for the Government representative, written certification accompanied by objective quality evidence (as de

41、fined in MIL-STD-109) , that the components used as a part of the TSAG meet the applicable requirements. 4.4 First article inspection. When specified in the contract or purchase order, the contractor shall furnish a first article of two TSAGs to the testing activity designated in the contract or pur

42、chase order for first article inspection and approval (see 6.3). First article approval is valid only on the contract under which it is granted, unless specifically extended by the procuring activity to other contracts. The first article shall be manufactured using the same methods, materials, proce

43、sses, and procedures proposed for production. Any production prior to approval of the first article shall be at the risk of the contractor. 4.4.1 First article inspection sequence. The first article sample of two TSAGs shall be subjected to the inspections of Table I in the sequence shown. 4.4.2 Fir

44、st article acceptance and rejection criteria. Failure of any TSAG to pass any of the first article inspections specified herein shall cause rejection of the first article sample. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-5284 70 W 77797

45、0b 0274053 7 S Inspection Visual and mechanical Performance tests High temperature Low temperature Shock Watertight Salt fog Dust (fine sand) Performance tests Individual acceptance tests MI L-T-85 284 ( AS ) Requirement Method paragraph paragraph 3.3, 3.5, 3.6 4.6.1, 4.6.4, 4.6.5 3.2.1.1, 3.2.1.2 4

46、.6.1 3.4.1 4.6.3.1 3.4.2 4.6.3.2 3.4.3 4.6.3.3 3.4.4 4.6.3.4 3.4.5 4.6.3.5 3.4.6 4.6.3.6 3.2.1.1, 3.2.1.2 4.6.1 3.2.1.3 4.6.2 TABLE I. First article inspection. 4.4.3 Disposition of first article sample. Disposition of first article samples shall be in accordance with the contract or purchase order

47、(see 6.2.1). 4.5 Quality conformance inspections. All TSAGs offered for acceptance shall be subjected to the quality conformance inspections and in the sequence specified in Table II. ments of Table II shall be rejected. Any TSAG that fails to meet the require- 8 Provided by IHSNot for ResaleNo repr

48、oduction or networking permitted without license from IHS-,-,-. . MIL-T-85284 70 7979906 0174054 7 MI L- T- 85 284 ( AS ) Inspection Requirement Method Visual and mechanical 3.3, 3.5, 3.6 4.6.1, 4.6.4, paragraph paragraph 4.6.5 Performance tests 3.2.1.1 , 3.2.1.2 4.6.1 Individual acceptance 3.2.1.3

49、4.6.2 tests TABLE II. Quality conformance inspection. 4.6 Methods of inspection. 4.6.1 Performance tests. The TSAG Al test card shall be tested for conformance to 3.2.1.1 and 3.2.1.2. 4.6.2 Individual acceptance test. The following individual acceptance tests shall be performed in accordance with NAVAIR 16-50 BAC 2-13 (see 3.2.1.3): a. TSAG circuit card test. b. MLV-to-MLV test. 4.6.3 Environmental tests. The envir