NAVY MIL-T-85471-1981 TEST SET INERTIAL MEASURING UNIT II TS3846 ASM-608V《TS3846 ASM-608V惯性测量装置 II试验装置》.pdf

1、-. _- MIL-T-85473 bb 7777706 0345239 2 m v MIL-T-85471 (AS) 6 July 1981 MILITARY SPECIFICATION TEST SET, INERTIAL MEASURING UNIT II, TS 3846IASM-608V This specification is approved for use by the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agenc

2、ies of the Department of Defense. 1. SCOPE L 1.1 Scope. This specification establishes the hardware and executive software design requirements for an Inertial Measuring Unit Test Set II (IMTS IL). The IMUTS II shall provide for maintenance support of the AN/ASN-92 Inertial Measuring Unit (IMU) and t

3、he AN/ASN-130 Inertial Navigation Group (ING) for both shore and sea based applications. 1.2 General. The Inertial Measuring Unit Test Set II (IMUTS II), TS 3846/ASM-608(V), contractors P/N 262200-1, shall consist of a two (2) bay console. 1.2.1 Test program sets (TPS) IMUTS II, when used with the a

4、ppro- priate Test Program Sets, shall provide for the test and fault isolation of those Weapons Replaceable Assemblies (I*) listed in table I. The TPS shall consist of those items necessary to test a Unit Under Test (UUT) on an IMUTS II. This includes the electrical, mechanical, instructional and lo

5、gic decision elements, These individual elements and their function shall be as defined in the latest procurement contract for IMUTS LI. 1.2.2 Control software. Control software for the Test Set shall be provided. requirements. Refer to paragraph 3.6.2 for a detailed description of the software *- 1

6、.2.3 Self-check program. A Self-check Program (SCP) and Self-check Interface Device (ID) shall be provided. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect on the date of invitation for bids, unless otherwise specified below, form a part of this specif

7、ication to the extent specified herein. Beneficial comments (recommendations, additions , deletions) and any pertinent data which may be of use in improving this document should be addressed to Commanding Officer, Naval Air Engineering Center, Engineering Specifications and Standards Department (Cod

8、e 9313), Lakehurst, NJ 08733 by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. THIS DQCWMENF CONTAINS PAGES. _- Licensed by Information Handling ServicesMIL-T-5i?I -6h- 9?999b 01115220 9 m MIL-T-85471 (AS) SP

9、EC IF ICAT IONS Elilitary MIL-B- 1000 MIL- E-1 7 5 5 5 MIL-N- 18307 ElIL-N-81604 MIL-T- 28800 STANDARDS Drawings, Engineering and Associated Lists Electronic and Electrical Equipment, Accessories, and Repair Parts; Packaging and Packing of Aeronautical Electronic and Associated Equipment, Nomenclatu

10、re and Nameplates for Navigation Set, Inertial (CAINS) AN/ASN-92 (V) Test Equipment for Use With Electrical and Electronic Equipment, General Specification for Military MIL-STD-46 1 Electromagnetic Interference Characteristics Requirements for Equipment, Subsystem and System MIL-S TD-4 80 Configurat

11、ion Control - Engineering .Changes, Deviations and Waivers Ped er a 1 FED-STD-595 Colors Naval Air Systems Command AR-10 Maintainability of Avionics Equipment and Systems, General Requirements for (Copies of specifications, standards, drawings, and publications required by contractors in connection

12、with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer .) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. the issue in effect on date of invitation for bids or requ

13、est for proposal shall Unless otherwise indicated, apply Litton G/CS 249467 261896 Engineering Test Equipment, General Requirements Installation Requirements, IMUTS II 2 Licensed by Information Handling ServicesMIL-T-8547L 66 m 7779906 OLq522L O m Litton G/CS (Continued) MIL-T-85471 (AS) IMUTS II ZI

14、F Connector Input/Output S-Anal and Power Interface Characteristics ATS Programming Manual FORTRAN Z Reference Manual Real Time Operating System Users Guide (Application for copies should be addressed to Litton Systems, Inc., Guidance and Control Systems Division, 5500 Canoga Avenue, Woodland Hills

15、, CA 91364 .) McDonnell Aircraft Company (MCAIR) MDC 388 F-18 Avionics Multiplex Design Specification (Application for copies should be addressed to the McDonnell Douglass Corporation, P. O. Box 516, Saint Louis, MO 63166.) Electronic Industries Association (EIA) RS- 2 3 2-C-69 Interface Between Dat

16、a Terminal Equipment and Data Communication Equipment Employing Serial Binary Data Inter change (Application for copies should be addressed to the Electronic Industries Association, 2001 Eye Street, N.W., Washington, DC 20006.) Institute of Electrical and Electronic Engineers (IEEE) 488-1975 Digital

17、 Interface for Programmable Instrumentation (Application for copies should be addressed to the Institute of Electrical and Electronic Engineers, 345 East 47th Street, New York, NY 10017.) 2.3 Precedence of documents. When the requirements of the contract, purchase order, this document or referenced

18、specifications herein are in conflict, the following precedence shall apply: a. Contract b. Purchase Order c. Equipment Specification d. Specifications referenced in a, b and c above. All IMUTS II component part numbers referenced in this document shall be considered to be those in effect at the.tim

19、e of first article acceptance. 3 Licensed by Information Handling ServicesMIL-T-8547 1 (AS) 3 REQUIRE3lENTS 3.1 First article. Then specified, the contractor shall furnish a sample unit for first article inspection and approval (see paragraph 4.4.2, First Article Demonstration Sample). 3.2 Parts, ma

20、terials, and processes. Parts, materials and processes shall be selected to conform to the requirements of Litton Specification 249467 and the performance and reliability requirements of this specification. 3.2.1 Finishes. The IFILITS II front panels shall be finished as follW3 : a. Contractor. Fede

21、ral STD 595, Color No. 26559 for door and panels; Color No. 26134 for side panels and trim. b. Commercial units. These finishes shall conform to the requirements for contractor designed units or shall be in accordance with MIL-T-28800. 3.3 Design and construction. The IMUTS II shall be designed to b

22、est commercial practice in accordance with Specification 249467. In addition, contractor designed units shall be classified- as Type III, Class 4, equipment in accordance with MIL-T-28800 with the following exceptions: a, The enclosure for the overall test station shall be manufactured in accordance

23、 with approved engineering drawings. b, The ambient operating range shall be 10C to 4OoC. ci Console air inlets may be less than 18 inches above the consolemounting surface. 3.3.1 Physical characteristics. The IMUTS II subassemblies shall conform to the physical characteristics specified below. 3.3.

24、1.1 Total weight. The maximum weight for the IMUTS II shall not exceed 2000 pounds. 3.3.1.2 Dimensions/form factor. Each IMUTS II shall conform to the dimensions and form factor shown in the installation drawing 261896. 3.3.2 Connectors. The IMUTS II shall utilize external connectors designed and se

25、lected to meet the requirements of MIL-T-28800. exposed male connector pins shall not carry voltages in excess of 30 volts when exposed. In addition, c 4 Licensed by Information Handling ServicesMIL-T-85473 bb 7779706 0345223 4 MIL-T-85471 (AS) 3.3.3 Electrical power sources and connections. The IMT

26、S IL shall operate when supplied with 115V, 60 Hz and 115V, 400 Hz ac power meeting the requirements of MIL-T-28800, except that 400 Hz power shall meet the require- ments of 400 +20 Hz, 3 phase, WE connected, ABC phase rotation, 5 wire (including Neutral and Earth Ground), 118 - +7V ac. 3.3.3.1 Pow

27、er transient. The IMUTS II. shall be capable of operating under the power transient conditions specified in MIL-T-28800 except that the duration of voltage and frequency transients shall not exceed 5 milliseconds. However, damage to IMUTS II requiring maintenance action shall not be incurred for dur

28、ations specified in MIL-T-28800. 3.3.4 Modularity. Placement of the IMUTS II modules shall provide for accessibility. replacement of its component modules or other major assemblies within the enclosure. Rear access shall not be required for the removal and/or 3.3.5 Internal controls and adjustments.

29、 Internal controls of contractor designed units shall be easily accessible and shall be designed such that their-position of normal adjustment is within the center 50 percent range whenever possible. 3.3.6 Controls, displays and indicators. Controls, displays and indicators shall be as defined by th

30、e contractors engineering drawings. 3.3.7 Interference control. The IMUTS II shall be designed such that the requirements of MIL-STD-461 are considered to the extent that these requirements are consistent with best comercial design practice and the requirements of this equipment specification. 3.3.8

31、 Reliability. The Mean Time Between Failures (MTBF) of the IMUTS II shall be a minimum 300 hours for the contractor designed assemblies and 150 hours for the total station. 3.3.8.1 Operating stability. The Equipment Verification Standard (EVS) shall be the reference source for calibration verificati

32、on of the Digital Multimeter and the Frequency Counter/Timer. The Digital Multimeter and the Frequency Counter/Timer shall be subject to periodic calibration as determined by the EVS. The EVS is subject to calibration in accordance with paragraph 3.6.1.4. The Digital Multimeter and the Frequency Cou

33、nter/Timer shall be used as a standard second source for all adjustments in the IMUTS II. The IMTS II shall operate within specified performance for a period of 2000 hours or six (6) months, whichever occurs first, continuously or intermittently, without the need for adjustment. 3.3.8.2 Total operat

34、ing life. The IMUTS II shall have a minimum total operating life of 25,000 hours with reasonable servicing and replacement of parts. 3.3.9 Maintainability. The IMTS II shall conform to the main- tainability requirements of the maintenance plan. 5 Licensed by Information Handling Services3.3.9.1 Stan

35、dard test equipment. It shall be possible to locate faults in contractor designed units using only the test system itself and test equip- ments normally available in intermediate shop facilities. 3.3.9.2 Category of faults. Failures in the IMlJTS II shall be divided into four categories: a, Category

36、 I: Faults which prevent program execution. b. Category II: Processor and peripheral faults which may be isolated with commercial supplied diagnostic programs. c. Category III: RTOS detected, in-process faults, which are out of scope for self-check. d. Category IV: Faults in the contractor designed

37、assemblies, and commercial units which are controlled by contractor designed interface. 3.3.9.3 Fault isolation. Category I faults shall be isolated using applicable procedures and common ground support equipment existing in Inter- mediate (I) level maintenance shops. Category II faults may be isola

38、ted to a functional area within the computer with the commercial supplied diagnostic programs. Category III faults shall be automatically detected by the Real Time Operating System and alert the operator to the area and the nature of the fault, Category IV faults are Self-check Program (SCP) detecta

39、ble and isolatible faults. SCP shall detect 98% of all Category IV faults. When a Category IV fault is detected, the Self-check Program shall isolate the fault to meet AR 10: to 1 card, 90% of time to 2 cards, 95% of time to 3 cards, 100% of time When cables, chassis mounted components, an instrumen

40、t, etc., are potential probable causes of failure, they will be included in the component callout. Maintenance times for Category IV fault shall be consistent with MIL-T-28800. 6 Licensed by Information Handling ServicesBIIL-11-85471 (AS) 3.3.9.4 Adjustments. Adjustments are required when a devices

41、parameters are out of tolerance but within the range of the adjustment to restore them to within tolerance. The need for adjustments is determined by a series of tests that are a subset of the.Self-Check Program. parameter be outside the range of adjustment availab,le to restore that parameter to wi

42、thin tolerance, the device is considered to have failed. to adjustment are: Should a devices Devices subject a. Processor Unit power supply voltages. b. Station fixed 5V dc supply voltages. c. Station multi-output fixed supply voltages. d. Programmable power supply offset, gain, and output. e. Ampli

43、tude of 26V ac, 400 Hz reference. f. Processor Unit AID converter offset and gain. 3.3.9.5 Initial settings. Certain devices have parameters that are set at time of installation and are not reset unless the device has been repaired or replaced. These parameters are: a. Actuation level of Processor U

44、nit power supply ACLO signal. b. Over voltage and over current limits of all power supply outputs. c. Frequency and voltage tolerance limits of optional Power Monitor, 3.3.9.6 Power supply safety. Power supply failures in the IMUTS II shall not cause damage to any UUT or to the IMUTS II. 3.3.9.7 Spe

45、cial tools. The IMUTS II shall not require special maintenance tools except for cleaning and aligning the disc readlwrite heads. 3.3.10 Service conditions. Console assemblies shall provide protection for subassemblies contained therein when subjected to the specified environmental conditions. 3.3.10

46、.1 Humidity. Contractor designed units of the IMUTS II shall operate satisfactorily at the temperature and humidity requirements specified herein. 7 Licensed by Information Handling ServicesMIL-T-85471 (AS) 3.3.10.2 Vibration. The IMUTS II is intended for aircraft carrier, mobile van and shore based

47、 installation and shall meet the vibration require- ments normally associated with transport of commercial equipment. requirements of MIL-T-28800 used as a design guide, the console shall meet the vertical vlbration requirements. However, for horizontal vibration (fore-aft and side-to-side), the con

48、sole may require additional support to limit the amplitude of sway. With the 33.11 Standard conditions. The following are the standard environ- mental conditions for demonstration of the ItUTS II. a, Temperature: 25OC - -t SOC b. Altitude: O to 4000 feet c. Vibration None d. Humidity: Up to 75% (wit

49、hout condensation) e. Input Power: 118V ac +7 volts, 400 Hz, 3 Phase 115V ac -f-lO%, - 60 Hz 3.3.12 Interchangeability. The IMUTS II shall meet the interchange- ability requirements specified in MIL-T-28800. 3.3.13 Safety. The IMUTS II shall be designed to meet the safety requirements of MIL-T-28800. 3.4 Nomenclature assignment. Nomenclature assignments for the IblTS II shall be determined, when required, in accordance with MIL-N-18307. 3.5 Functional description. The basic IMUTS II shall have the capability to test the Carrier Aircraft Inertial Navigation System (CAINS)