NAVY MIL-T-85472 A-1987 TEST SET GROUP OQ-169B DSM-96A SPECIFICATION FOR《OQ-169B DSM-96A组试验装置规范》.pdf

1、MIL-T-85472A(AS) 4 AUGUST 1987 MIL-T-85472(AS) SUPERSEDING 14 May 1985 MILITARY SPECIFICATION TEST SET, GROUP OQ-169B/DSM-96A9 SPECIFICATION FOR This specification is approved for use within the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agenci

2、es of the Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the design, performance, and acceptance requirements for the Group OQ-169B/DSM-96A Test Set herein referred to as the test set. The test set is for shore installation and is used with the Guided Weapon Test Set AN/DS

3、M-96A to test the operational status of Walleye Data Link Weapons and Walleye Phase II Data Link Weapons. 2. APPLICABLE DOCUMENTS 2.1 Government Documents. 2.1.1 Specifications and standards: The following specifications and standards form a part of this specification to the extent specified here Un

4、less otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications Standards (DODISS) and supplement thereto, cited in the solicitation. I I Beneficial comments (recommendations, additions, deletions) end any pertinent data

5、 which may be of use in improving this document should be eddressed to: Commanding Officer, Naval Air Engineering Center, Systems Engineering ad Standardization Department (SESD) Code 93, Lakehurst, NJ 08733-5100, by usinq the self-addressed Standardization Document Improvement Proposal (DD Form 142

6、6) eppearing at the end of this document or by letter. I I AMSC N/A Distribution Statement A. Approved for pub1 ic release; distribut THIS DOCUMENT CONTAINS 4d PAGES. n. and FSC 4935 on is unlimited, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SP

7、EC I F ICAT I ONS FEDERAL PPP-B-636 M I 1 I TARY MIL-P-116 MIL-S-901 MI 1-T-5422 WS-6536 MI 1- E-16400 MIL- E-17555 MI L-T-28800 MI L-T-8503 1 STANDARDS MI L ITARY MIL-STD-129 MI L - STD- 130 MI L-STD-454 MIL-STD-461 MIL-STD-462 MIL- STD- 704 MI L -STD- 781 MI L - STD- 81 O Boxes, Shipping , Fi berb

8、oard Preservation and Packaging, Methods of Shock Tests, H.I. (High Impact); Shipboard Machinery Equipment and Systems, Requirements for Testing, Environmental, Airborne Electronic and Associated Equipment Procedures and Requirements for Preparation and Soldering of Electrical Connections El ectroni

9、c, Interior Communication, and Navigation Equipment, Naval Ship and Shore, General Speci fi cat i on for L Electronic and Electrical Equipment, Accessories, and Repair Parts; Packaging and Packing of Test Equipment for use with Electrical and Electronic Equipment , General Speci fi cat i on for Test

10、 Set, Guided Weapon, AN/DSM-96A Marking for Shipment and Storage Ident i fi cati on Marking of US Mi 1 i tary Property Standard General Requirements for Electronic Equipment Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference Electromagnetic Inter

11、ference Characteristics, Measurement of Electric Power, Aircraft Characteristic and Uti1 ization of Reliability Tests and Exponential Distribution Environmental Test Methods 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-T-85q72A Li9 9999906

12、0258308 T MIL-T-85472A(AS) MIL-STD-965 Parts Control Program 2.1.2 Drawings and publications. The following drawings and publications form a part of this specification to the extent specified herein. otherwise specified, the issues shall be those in effect on the date of the solicitation. Unless NAV

13、AL AIR SYSTEMS COMMAND DRAWINGS DL412AS9000 Test Set, Group OQ-169B/DSM-96A PUBLICATIONS NAVAIR 16-3504169-1 Maintenance Instructions with Illustrated Parts Breakdown (Intermediate-Depot) Test Set, Group OQ-169B/DSM-96A NAVAIR 16-350Q169-1A Secret Supplement, Test Set, Group OQ- 169B/DSM-96A (Copies

14、 of specifications, standards, drawings, and publ ications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. specification to the extent specified herein. Unl

15、ess otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS specified the supplement thereto, if applicable. The following documents form a part of this Instruction Manual for Power Meter and Thermistor Mount, Hewlett-Packard, Model HP-

16、 432A (Appl i cat 1501 Page Instruction Manual for Power Supply, Hew1 ett - Pac kard, Model HP-60155C on for copies shall be addressed to the Hewlett-Packard Company, Mill Road, Palo Alto, California 94304.) Instruction Manual for TV Monitor, Conrac Div, Giannini Control Corporation, Model PVA17/R o

17、r SNA17/R (Application for copies shall be addressed to the Conrac Corp/Controls Group 3, Landmark Square, CT, 06901.) (Nongovernment standards and other publ ications are normally available from the organizations which prepare or which distribute the documents. documents also may be available in or

18、 through libraries or other informational services.) These 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-T-CV7iA i7 7999706 01258109 1 W MIL-T-85472A(AS) 2.3 Order of precedence. In the event of a conflict between the text of this specificat

19、ion and the references cited herein (except for associated detail specifications, specification sheets, or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been

20、 obtained. 3 REQUIREMENTS 3.1 conjunction with Guided Weapon Test Set AN/DSM-96A to operationally test the Walleye Data Link Guided Weapons. The test set shall consist of the principal assemblies shown on figure 1. 3.1.1 Interface description. The OQ-169B/DSM-96A Test Set Group shall be interconnect

21、ed with Guided Weapon Test Set AN/DSM-96A as shown on figure 2 for Walleye weapon testing. The OQ-169B and DSM-96A test consoles shall contain all the switches and indicators required to enter the test commands .and monitor the responses of the weapon under test. The OQ-169B/DSM-96A Test Set Group s

22、hall be capable of checking all the parameters unique to data link/PHASE I and II weapons. All remaining parameters shall be checked with the DSM-96A test set (see MIL-T-85031). Figure 3 depicts a typical weapon test setup using OQ-169B and DSM-96A test sets as a unit. 3.2 First article. When specif

23、ied in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.4 and 6.3). 3.3 Parts and materials. 3.3.1 Nonstandard parts and material approval. Approval for the use of nonstandard parts and materials shall be obtained by the contractor as specified in MIL-ST

24、D-965. 3.3.2 Basic conformance. Material selected for use in the equipment shall be as specified in MIL-T-28800. conforming to MIL-E-16400, unless the parts listed therein will not perform adequately in the intended applications and environments specified herein in which case 3.3.1 applies. 3.3.3 In

25、terchangeability. All parts and materials shall meet the interchangeability requirements as specified in MIL-T-28800. The drawings conforming to DL412AS9000 shall be the standard for measuring interchange- ability of all applicable units, and assembling subassemblies and parts. 3.4 Design and constr

26、uction. The test set group shall be manufactured in accordance with the drawings and subsidiary specifications conforming to DL412AS9000, except that errors of omission or commission on the drawings may be incompatible with the requirements of this specification. In any case, it is a condition of fi

27、nal acceptance that the equipment manufactured shall meet all the design, construction, and workmanship requirements of this specification and applicable test documents. 3.4.1 Reliability. 3.4.1.1 Operational stability, The test set group shall operate with required performance, continuously or inte

28、rmittently for a period of not less Item description. Test Set Group OQ-169B/DSM-96A shall be used in Parts shall be selected from those 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-85472A 49 W 7979906 0258330 B W MIL-T-85472A(AS) PHASE I

29、 ANTENNA SHROUD ASSEMBLY PHASE II ANTENNA SHROUO ASSEHBL NOTE: THE USE Of ITEM 3 412AS9003 ATTENUATOR IS SUSPENDE0 PENDING THE AOOITION OF THE RF SHIELOINC OF THE WEAPON TEST CELLS. .6W6 y-p.;y.:;2T=z7 I_ .- L=.l yv1- .rs -Jgq-TJll iW501 -c-r FIGURE 1. Test Set Group OQ-169B/DSM-96A. 5 - . i . . . .

30、 *. ,. - .- - -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-+Jj I I III e# I I 10 if1 - VAC Ut FIGURE 2. Test Set Group OQ-169B/DSM-96A interconnection diagram. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

31、se from IHS-,-,-MIL-T-85472A 47 777770b 0258L12 L MI L -T- 85472A (AS) FIGURE 3. Typical Walleye test set ups. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-85Ll7ZA Li9 9499906 02CBlL3 3 MI L-T-85472A(AS) than 300 hours. During this time, i

32、t shall not be necessary to readjust any controls that are inaccessible to the operator during normal use. 3.4.1.2 Operating life. The test set group shall have a total operating life of not less than 2000 hours with minimal servicing and replacement of parts 3.4.1.3 Reliability in mean-time-between

33、-failures (MTBF). The test set group shall have a specified mean (operating) time between failures of 300 hours when tested in accordance with 4.5.3. 3.4.2 Standard conditions. The following conditions shall be used to establish the normal performance characteristics under standard conditions for pe

34、rforming laboratory bench tests: a. Temperature Room ambient (30 210 OC b. Altitude Normal ground c. Vibration None d. Humidity Room ambient up to 90 percent relative humi di ty e. Input Power 115 211.5 volts, 60 23 Hz, 1 phase at 3400 volt-amperes, 30 (t.2) (-0.0) volts dc, 5 amperes 3.4.2.1 Servic

35、e conditions. The test set shall operate as required under any of the environmental service conditions or reasonable combination of these conditions as specified in MIL-E-16400, except as modified herein: 3.4.2. I 1 Temperature. a. Operating. The test set group shall maintain specified performance w

36、hi 1 e exposed to 1 ow Operating temperatures of -0 OC and high operating temperatures of 150 C. b. Non-operating. shall operational performance be degraded when restored to the operational temperature range after being subjected to a nonoperating low temperature of -62 OC and a high nonoperating te

37、mperature of +7l OC. The test set group shall not be damaged nor 3.4.2.1.2 Vibration. The test set group shall meet the requirements of 4.9.2 for equipment transported as secured cargo. 3.4.2.1.3 Shock, The test set shall be capable of withstanding the Grade A, Class I, shock requirements of MIL-S-9

38、01. 3.4.2.1.4 Humidity, The test set shall maintain the specified performance when exposed to a relative humidity of 95 percent for both continuous and intermittent periods, including conditions wherein condensation takes place in and on the equipment in the form of both water and frost. 8 Provided

39、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-85472A 49 7979706 0258114 5 W MI L-T-85472A (AS) 3.4.2.1.5 Fungus. The test set shall be resistant to fungi in both the operating and nonoperating condition and shall not be adversely affected when tested

40、in accordance with 4.9.5. 3.4.3 Warm-up time. to operation shall be not greater than 10 minutes under standard conditions and 30 minutes under service conditions. The time required for the equipment to warm-up prior 3.4.4 Primary input power requirements. power requirements as specified in MIL-STD-7

41、04 for Class 2 equipment. power required shall be of the following type and shall be not greater than the specified values: The test set shall meet input The a. 115 k11.5 volts ac, 60 +3 Hz, 1 phase, 3400 volt-amperes b. 30 (t2.0) (-0.0) volts dc, 5 amperes 3.4.4.1 Electrical overload protection. El

42、ectrical overload protection for the test set group shall conform to Requirement 8 of MILySTD-454 for Class 1 equipment. 3.4.5 Electromagnetic interference. The generation of electromagnetic interference by the test set and the susceptibility of the test set t6 electromagnetic interference shall be

43、in accordance with MIL-STD-461 as referenced in MIL- E- 16400. 3.4.5 1 not be susceptible to signals from 50 Hz to 400 MHz injected on the 115 V ac power leads as specified in MIL-STD-461, Requirement CS02. Conducted suscept i bi 1 i ty, power 1 eads. The test set group shall 3.4.5.2 Conducted emiss

44、ion, power leads. Conducted emissions from the test set arouD Dower leads sh.all be within the limits of MIL-STD-461, Requireminis CE02 and CE04. 3.4.5.3 Conducted emission, control, and signa from the test set control and signal leads shal MIL-STD-461, Requirements CE03 and CS05. 3.4.5.4 Radiated s

45、usceptibility. The test set radiated signals from 30 Hz to 12.4 GHz as spec Requirements RSO1, RS03 and RS03.1. 1 ead be w shall fied . Conducted emissions thin the limits of not be susceptible to n MIL-STD-461, emissions from the 3.4.5.5 Radiated emission, electric field. Radiated test set over the

46、 frequency range of 14 Hz to 1000 MHz, shall be within the limits of MIL-STD-461, Requirement RE02. 3.4.5.6 Transient voltage. The test.set group shall meet the requirements of MIL-E-16400 for transient high and low voltage. 3.4.5:7 Transient frequency. The test set group shall meet the requirements

47、 of MIL-E-16400 for transient high and low frequency. 3.4.5.8 Power interruption. The test set group shall meet the requirements of MIL-E-16400 for power interruption. 3.4.6 Dimensions. The dimensions of the test set group shall be not greater than the following: 9 Provided by IHSNot for ResaleNo re

48、production or networking permitted without license from IHS-,-,-MIL-T-5472A 47 7777906 02581157 a. Height 78.76 inches b, Width 40.5 inches c. Depth 36.5 inches 3.4.7 Weight. The total weight of the test set group console shall be not greater than 700 pounds. 3.4.8 Color and finish. The color and fi

49、nish of the test set shall be in accordance with DL412AS9000, 3.4.9 Identification plate and item markings. Nomenclature and identification marking shall be in accordance with MIL-STD-130 and DL412AS9000. 3.5 Performance. The performance of the test set group shall be as specified herein in addition to the performance requirements specified in DL412AS9000. Unless otherwise specified h