NAVY MIL-V-17501 F-1990 VALVES CONTROL TYPE MAGAZINE AND HANGAR DECK SPRINKLER《弹药舱喷淋和飞机库甲板喷淋控制阀》.pdf

1、MIL-V-LiSOLF L(8 D 999990b 045775b T 1 INCH-POUND j MIL-V-l7501F(SH) - SUPERSEDING MIL-V-l750lE( SH) 24 March 1970 MILITARY SPECIFICATION VALVES, CONTROL TYPE, MAGAZINE, AND HANGAR DECK SPRINKLER This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is

2、available for use by all departments and agencies of the DePafiment of Defense. 1. SCOPE 1.1 Scope. This specification covers magazine and hangar deck sprinkler control type valves for shipboard service. 1.2 Classification. Valves shall be of the following types and classes as specified (see 6.2): T

3、ype I - Diaphragm actuated, hydraulic operated, 250 pounds per square inch (lb/in2) Class 1 - Sprinkler supply, globe type, normally closed with manual actuation Class 2 - Remote control, globe type, normally closed Class 3 - Lift check, spring loaded, globe type, normally closed Class 4 - Hydraulic

4、 check, globe type, normally closed Class 5 - Hydraulic control, globe type, normally closed Class 6 - Three-way control, four port Type II - Manual operated, 250 lb/in2, rotary disc plate type. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in

5、 improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA Fsc

6、 4810 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-17501F ri8 999990b 0457757 L hlll .- 17501F(SH) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Spec

7、ifications, standards, nnd handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and S

8、tandards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL QQ-A-601 QQ-B-626 QQ-B-637 QQ-B-654 QQ-N-281 QQ-W-390 QQ-W-428 MILITARY MILV-3 MIL-S-901 MIL-G-1149 MIL-F-1183 Aluminum Alloy Sand Castings Brass, Leaded and Nonleaded: Rods, Shapes, Forgings, and F

9、iat Products with Finished Edges (Bar and Strip) Brass Naval: Rod, Wire, Shapes, Forgings, and Flat Products with Finished Edges (Bar, Hat Wire, and Strip) Brazing Alloys, Silver Nickel-Copper Alloy Bar, Rod, Plate, Sheet Strip, Wire, Forgings, and Structurai and Special Shaped Sections Wire, Nickel

10、-Chromium-Iron Alloy Wire, Steel, Carbon (High Carbon, Round, for Mechanical Springs, General Purpose) Valves, Fittings, and Flanges (Except for Systems Indicated Herein); Packaging of Shock Tests, HI (High-Impact) Shipboard Machinery, Equipment, and Systems, Requirements for Gasket Materials, Synth

11、etic Rubber, 50 and 65 Durometer Hardness Fittings, Pipe, Cast Bronze, Silver Brazing, General Specification for 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-5315 MIL-C-8068 MIL-P-15024 MIL-P-15024/5 MIL-T- 16420 MIL-B-16541 MIL- F-20042 S

12、TANDARDS FEDERAL FED-STD-H28 FED-STD-H28/7 MILITARY MIL-STD- 130 MIL-STD-167-1 MIL-STD-777 nIL-V-2750LF Li (DOD adopted) Standard Specification for Stainless and Heat-Resisting Steel, Bars and Shapes; (DOD adopted) Standard Specification for Steel, Wire, Music Spring Quality; (DOD adopted) Standard

13、Specification for Chromium-Nickel Stainless and Heat-Resisting Steel Spring Wire; (DOD adopted) Standard Specification for Free-Machining Stainless and Heat-Resisting Steel Bars, Hot-Rolled or Cold-Finished Standard Specification for Steam or Valve Bronze Castings; (DOD adopted) Standard Specificati

14、on for Nickel-Copper Alloy Rod, Bar, and Wire; (DOD adopted) Standard Specification for Aluminum Alloys in Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings; (DOD adopted) Standard Specification for Copper Beryllium Alloy Plate, Sheet, Strip and Rolled Bar; (DOD adopted) Standa

15、rd Specification for Vulcanized Fiber Sheets, Rods, and Tubes Used for Electrical Insulation; (DOD adopted) Standard Classification System for Rubber Products in Automotive Applications; (DOD adopted) (Application for copies should be addressed to the American Society for Testing and Materials, 1916

16、 Race Street, Philadelphia, PA 19103.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 23 Order of precedence. In t

17、he event of a conflict between the text of this specification and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 4 Provided by IHSNot for ResaleNo re

18、production or networking permitted without license from IHS-,-,-MIL-V-l750lF(SH) 3. REQUIREMENTS 3.1 Qualification. Valves furnished under this specification shall be products which are authorized by the qualifying activity for listing on the applicable qualified products list at the time of award o

19、f contract (see 4.3 and 6.5). 3.2 Materials. The materials of parts shall be as specified in table I. Alternate materials not specified herein shall not be used unless prior approval by Naval Sea Systems Command (NAVSEA) has been received. Such materials shall be suitable for long-term reliable serv

20、ice under the operating conditions specified. Such materials shall be subject to the results of qualification tests and examinations and to acquiring activity concurrence. In selecting materials, contractors should consider that, in addition to service usage, these valve assemblies shall be subject

21、to periods of inactivity. Lightness of weight shall be a consideration; use of magnesium is not approved. For parts working against each other, materials shall be selected to prevent galling, seizing, and excessive wear. Material identification shall include the commercial, industrial, federal, or m

22、ilitary specification to which the material conforms and shall indicate the type, grade, or class of the material if classified in the applicable material specification. Materials used in the construction of components shall be shown and identified on the appropriate drawings and associated lists of

23、 those components (see 6.3). TABLE I. Materials and application. Name of part Valve Body Intermediate valve body Distributor Valve seat WY Valve seat (upper and lower) Valve disc/ retainer assembly Valve disc and skirt Valve stem and guides Material Bronze Bronze Bronze Ni-Cu alloy Ni-Cu alloy Ni-Cu

24、 alloy Synthetic rubber alloy alloy Ni-Cu Ni-Cu Applica ble document MIL-B-16541 ASTM B 61 MIL-B-16541 ASTM B 61 MIL-B-1654 1 ASTM B 61 QQ-N-281 ASTM B 164 QQ-N-281 MTM B 164 QQ-N-281 ASTM B 164 MIL-CS068 ASTM D 2000 QQ-N-281 ASTM B 164 QQ-N-281 ASTM B 164 5 Type CLl X - X X X X X CL2 X - X X X X *

25、and CI CL3 - X X X X X tion CL4 X X X X X X X X X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Name of part Valve stem Plug, cap Cover Spring (internai)l Diaphragm O-rings Diaphrafm washer Washers Indicator washer Unions Tube Gasket Te

26、st fitting Pin Roll pin Indicator stem flIL-V-17501F 48 = 999990b Oq537bl 3 = M 1 L-V- 1 7501F(SH) TABLE 1. Materials and application - Continued. Material Ni-Cu alloy Bronze Bronze Nickel- chrom- ium-iron Synthetic rubber Synthetic rubber Ni-Cu alloy Ni-Cu alloy Fiber BfOm Cu-Ni Synthetic rubber Al

27、uminum alloy (re- movable) Bronze manent) Ni-Cu alloy (per- Copper- beryl alloy Stainless steel Brass Applicable document QQ-N-281 ASTM B 164 MIL-B-16541 ASTM B 61 MIL-B- 1654 1 ASTM B 61 QQ-W-390 MIL-C-8068 ASTMDUWW) MIL-P-5315 QQ-N-281 ASTM B 164 QQ-N-281 ASTM B 164 ASTM D 710 MIL-F-1183 MIL-T-164

28、20 (70-30, type 1) MIL-G-1149 ASTMDUWK) QQ-A40 1 ASTM B 179 MIL-B-16541 ASTM B 61 QQ-N-281 ASTM B 164 ASTM B 194 ASTM A 276 QQ-B-637 - CLl Type CL2 X X X X X X X X X X X X X X X X X X X X Applic and cli Cl3 - X X X X X X ion b (CL) CL4 X X X X X X X X X X X X X X X X X - CL6 X - X X X X X X X - Type

29、 II X X X X X X X X X 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Name of part Indicator assembly adapter Indicator assembly housing Indicator assembly sight tube Spacer Brazing ring Spring (external) Driver Handle and lever Kq. Retaining ring

30、Chain Screws Bolts and Nut Data piate DiaVdata plate studs MIL-V-/?SOLF lt9 999990b Oir577b2 5 m MI I-.- 17501 F(SH) TABLE I. Moicriai ad application - Continued. Material Stainless steel BRSS pyrex Ni-Cu alloy Silver alloy Stainless steel alloy Aluminum alloy Brass alloy Brass Stainless Steel Brass

31、 alloy alloy Ni-Cu alloy Brass Brass Ni-Cu Ni-Cu Ni-Cu Ni-Cu Applim ble document ASTM A S2 QQ-B-637 Commercial QQ-N-281 ASTM B 164 QQ-B-654 ASTM A 313 QQ-N-281 QQ-A401 ASTM B 179 QQ-B-637 QQ-N-281 QQ-B-626 ASTM A 193 QQ-B-637 QQ-N-281 ASTM B 164 QQ-N-281 ASTM B 164 00-N-281 ASTh4 B 164 QQ-B-626 QQ-B

32、-626 Application Type I and class (CL) - CL 1 X - X X X X X X X X - CL2 - X X X X - - CU - X X X X - ., - CL4 - X X X X X - CL5 - X X X X X X - CU - X X X X X X X X X X X X For springs not in a wetted chamber, springs may be plastic or rubber coated carbon steel ASTM A 228 for diameters On class 1 v

33、aives larger than 2-inch, diaphragm washer material may be bronze MIL-B-16541 or ASTM B 61. of 0.250 inch and under; and QQ-W-428 over diameters greater than 0.250 inch. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-1750LF r 9999906 OLi5776

34、3 7 MlL-V-I7501F(SH) 33 Recovered materials. Unlcss ot hewisc specified herein, all equipment, material, and articles incorporated in the products covcrcd by this specification shall be new and may be fabricated using materials produced from rccovered materials to the maximum extent practicable with

35、out jeopardizing the intended use. The term “recovered materials” means materials which have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the use of used or re

36、built products is allowed under this specification unless otherwise specifically specified. 3.4 Component parts. Table I lists the general component parts and their application to the valves covered in this specification. The parts application is intended for guidance only; however, when parts liste

37、d are incorporated in the valve construction, materials of such parts shall be as specified. This general guidance shall not relieve the contractor from delivering valves that meet the specified requirements of this document. 3.5 Construction. Control valves shall be constructed for use with seawate

38、r. Functional construction characteristics for type I, class 1 through 6, and type II valves shall be as specified in 3.5.1 through 3.5.3 (see 6.3). Weight and size of the assembled valves shall be kept to a minimum. 3.5.1 Design pressure. Control valves shall be constructed for an internal operatin

39、g pressure of 250 lb/in2 and shall withstand an internal test pressure as specified in 4.6.3. The bonnet, dome, cover, or distributor portion of the valve shall be constructed to withstand the highest control pressure to which it will be subjected in the specified working range. 3.5.2 Type I. Contro

40、l valves of the type I classification shall be constructed for hydraulic operation. The movement of the valve disc shall be positively actuated by hydraulic pressure upon the diaphragm when subjected to a minimum fluid pressure of 40 lb/in2 while controlling fluids in a range of 40 to 250 Ib/in2. Di

41、aphragms shall not be employed as a disc or seating element. Control valves shall be constructed so that failure of the diaphragm will cause the valve to remain closed and shall seat with line pressure. Control valves shall be of the globe pattern construction in which all moving parts shall be guid

42、ed. Type I valve construction shall be as specified (see 3.6 through 3.6.16). 3.5.2.1 Class 1. Sprinkler supply valves shall be constructed to be held in the closed position by a combined force of valve spring and inlet firemain supply pressure acting on the valve disc. The valves shall be construct

43、ed to open rapidly when actuated by hydraulic pressure and close rapidly when hydraulic pressure is released. These valves shall permit control of seawater flow to the systems sprinkler head valves. Class 1 valves shall be constructed with an atmospheric vent, a valve position indicator, a test fitt

44、ing, and a manual actuation mechanism. 3.5.2.2 Class 2. The remote control valve shall be constructed to be held in the closed position by an internal valve spring when the control system piping is not pressurized. The valve shall be constructed to open fully and close completely when actuated by hy

45、draulic pressure. This valve shall permit securing of the sprinkler supply valve from an operation station other than the one from which actuation occurred. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-V-L750/F ri 999990b OY577bY 9 D M IL-V

46、- I 7501 F(SH) I 3.5.23 Class 3 The spring-loaded lift check valve shall be constructed to be held in the closed position by an internal valve spring when the control system piping is not pressurized. The valve shall be constructed to open fully and establish flow through the valve when hydraulic pr

47、essure is applied to the inlet side of the valve. The valve shall close completely when hydraulic pressure is applied in the reverse direction through the outlet side of the valve. This valve shall permit thecontrol system to be operated from more than one operating station by preventing reverse flo

48、w. 3.5.2.4 Class 4. The hydraulic operated check valve shall be constructed to be held in the closed position by an internal valve spring. The valve shall open fully when hydraulic pressure is applied to the valve through an actuation connection and close completely when pressure is relieved. This v

49、alve shall provide the means for venting the hydraulic pressure from the sprinkler supply valve, thereby permitting the sprinkler supply valve to close. 3.5.2.5 Class 5. The hydraulic operated control valve shall be constructed to be held in the closed position by an internal valve spring when the control system piping is not pressurized. The valve shall open fully when hydraulic pressure is applied to the valve through an