NAVY MIL-V-18318 B-1966 VALVE PRESSURE REGULATING OXYGEN SYSTEM《高压氧阀心》.pdf

1、f - I MIL-V-13LB 48 m 7777906 0273386 b m - MlL-V-18318B 29 September 1966 Superseding 8 April 1958 MIL-V-18318A. (ASG) MILITARY SPECIFICATION VALVE, PRESSURE REGULATING, OXYGEN SYSTEM This specification is mandatory for use by all Departments and Agencies of the De- partment of Defense. 1. SCOPE 1.

2、1 Scope - This specification covers an oxygen pressure regulating vaive. 1.2 Classification - Regulathg valves shall be of the following types (see 6.2). Type1 - 7Opsi Typen - 400 psi 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids or reques

3、t for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS Federal 0-T-236 0-T-634 BB-N-411 PPP-T-60 PPP-B-591 Trichloroethylene (Perchloroethylene) Technical Grade Trichloroethylene, Technical Nitrogen, Technical Tape, Pressure-sensitive Adhesive, Vinyl Plastic

4、 Film Box, Fiberboard, Woodcleated Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-7105 MIL-S-7742 MIL-A-8625 MIL-F-22191 MIL-V-18318B PPP-B-636 PPP-B-640 Military MIL-P-116 MIL-C-5541 *- i MIL-0-272 1 O MIL-T-27730 STANDARDS Federal FED-STD-59

5、5 _ . . .- Box, Fiberboard Box, Fiberboard, Corrugated, Triple-wall Preservation, Methods of Chemical Films and Chemical Film Materials For Aluminum and Aluminum Ailsys Pipe Threads, Taper, Aeronautical National Form, Symbol ANPT, General , Requirements For Screw Threads, Standard, Optimum Selected

6、Series, General Specification For Anodic Coatings, For Aluminum And Aluminum Alloys Films, Transparent, Flexible, Heat Sealable, For Packaging Applications Oxygen, Aviators Breathing, Liquid and Gas Tape, Antiseize, Tetra- fluoroethylene, With Dispenser Colors r Provided by IHSNot for ResaleNo repro

7、duction or networking permitted without license from IHS-,-,-I . MIL-V-L3LB 48 = 7777906 0273188 T Military MIL-STD-105 MIL-STD-129 MIL-STD-I30 MIL-STB-143 Sampling Procedures And Tables For hspection By Attributes Marking For Shipment And Storage Identification Marking Of U. 8. Military Property Sp

8、ecifications And Standards Order Of Precedence For The Selection Of MS20913 Plug, Square Head Pipe Thread MS33586 Air Force-Navy Aeronautical AND10053 Metals, Definition Of Dissimilar Bosses, Pipe-Thread, Internal-Standard Dimensions For (Copies of specifications, standards, drawings, and publicatio

9、ns required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 Qualification - The valve furnished under this specification shall be a product which has been tested, and passed

10、the qualification tests specified herein, and has been listed on or approved for listing on the applicable qualified products list. 3.2 First article - The valve furnished under this specification shall be a product which has been inspected, and passed the first article inspection specified herein.

11、3 f I 4 -. I i ., . I i?, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-183L8B LJ8 m 9979706 0273387 L m MIL-V-18318B 3.3 Selection of specification and standards - Specifications and standards for necessary commodities and services not speci

12、fied herein shall be selected in accordance with MIL-STD-143. 3.4 Materials - Materials shall conform to applicable specifications and shall be as specified herein and on applicable drawings. Materials which are not covered by specifications, or which are not specifically described herein, shall be

13、of the best quality, of the lightest practicable weight, and suitable for the purpose intended. 3.4.1 Metal parts - All metal parts shall be of a corrosion-resistant material or treated in a manner to render them adequately resistant to corrosion. 3.4.1.1 Dissimilar metals - Unless suitably protecte

14、d against electrolytic corrosion, dissimilar metals shall not be used in intimate contact with each other. Dissimilar metals are defined in MS33586. 3.4.2 Nonmetallic materials - Any nonmetallic material that is adversely affected by continued use with oxygen shall not be used. 3.4.2.1 Age - Elastom

15、er components, except silicone, shall not be more than 12 months old from the cure date of manufacture to the date of delivery to any Government Service or to any airframe or accessory manufacturer. 3.4.3 Protective treatment - When materials are used in the con- struction of the valve that are subj

16、ect to deterioration when exposed to environmental conditions likely to occur during service usage, they shall be protected against such deterioration in a manner that will in no way prevent compliance with the performance requirements of this specification. Protective coating which might crack, chi

17、p, or scale during normal service life or under extremes of environmental conditions shall not be used. 3.5 Standard parts - MS and AN standard parts shall be used where they suit the purpose. They shall be identified on the manufacturers drawings by their part numbers. Parts which are not covered b

18、y specifications or military standards, or which are not specifically described herein or on the drawings, shall be completely described on manufacturers drawings. 3.6 Design and construction - The pressure regulating valve shall be designed in accordance with Figure 1. The valve shall be capable of

19、 reducing inlet pressures, up to 2,000 psi, to low pressures at the outlet. An adjustable pressure reduction control shall be provided for pre-setting the outlet pressure to a predetermined fixed pressure within the range of 70 to 400 psi. 4 Q Provided by IHSNot for ResaleNo reproduction or networki

20、ng permitted without license from IHS-,-,-RIL-V-L3LB LJ = 7797906 0273190 W . MIL-V-18318B 3.6.1 Filter - A 200 mesh screen filter or equal shall be firmly secured in the valve inlet. This unit shall be easily removable for cleaning and replacement. , 3.6.2 Pressure relief valve - A pressure relief

21、valve, which shall pass the performance requirements specified in 3.7.4., shall be incorporated in the low pressure portion of the pressure regulating valve. 3.6.3 Orientation - “he valve shall operate satisfactorily in any position i. wkkh the valve is mounted (see 4.6.3). 3.6.4 Antiseize tape - An

22、tiseize tape shall be used on all male pipe thread fittings. Antiseize tape shall conform to and shall be applied as specified in MIL-E-27730. Tape shall not be used on flare tube fitting straight threads, coupling sleeves, or on the outer side of tube flares. None of the tape shall be allowed to en

23、ter the inside of a fitting. 3.7 Performance - 3.7.1 Leakage - The valve, when tested as specified in 4.7.2, shall not show my evidence of leakage. 3.7.2 Pressure and flow - The valve, when tested as specified in 4.7.3, shall have the pressure reduction characteristics specified in Table I. TABLE I

24、Flow Characteristics 5 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-V-333B 48 9 3739906 0273373 T -_ MIL-V- l83f8B I- r 4 4.000MAX DIA I 1 1 2.500 MAX I BOSSES IN - WITH AND1005 2.000 2.000 4 . . 4 HOLES SPACED INLET MAX -PLUGGED ALTE R N A

25、T E OUTLET PART NO.MS20913-I DIMENSLONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES : ANGLES2i: DECIMALS 2 .O16 FIGURE I Valve Dimensions i- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V- 1831 8B 3.7.3 Outlet pressure - The outlet press

26、ure of the valve, when tested as specified in 4.7.4, shall be equal to the preset outlet pressure with the following allowable tolerances: Outlet pressure range Tolerance 400 psi f 10 psi 70 psi f 5 psi 3.7.4 Pressure relief - 3.7.4.1 T.ype I - The pressure relief valve, when tested as specified ia

27、4.7.5, shall open when the pressure in the low-pressure side of the pressure regulating valve exceeds 120 psi and the relief valve shall close at not less than 100 psi. 3.7.4.2 Type D - The pressure relief valve, when tested as specified in 4.7.5, shall open when the pressure in the low-pressure sid

28、e of the pressure regulating valve exceeds 600 psi and the relief valve shall close at not less than 500 psi. 3.7.5 High and low temperature operation - The valve, when tested as specified in 4.7.6; shall operate without failure and shall not show any evidence of mechanical or material failure. 3.7.

29、6 - Vibration - The valve, when tested as specified in 4.7.7, shall not show ary evidence of mechanical or material failure. 3.7.7 Endurance - The valve, when tested as specified in 4.7.8, shall not show any evidence of mechanical or material failure. 3.7.8 as specified in 4.7.9, shall not ignite an

30、d there shall not be any evidence of charring or deterioration. Oxygen bomb test - The pressure regulating valve, when tested 3.8 Interchangeability - All parts having the same manufacturers part number shall be functionally and dimensionally interchangeable. 3.9 Weight - The .weight of the pressure

31、 regulating valve shall not exceed 1 l/Z pounds. 3.10 Threads - 3.10.1 1. . , Screw - -Machine screw threads shall be in accordance with MIL-S-7742. . .- 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_- - - +-I.- MIL-V-L3LB L1 - 7977706 0273393

32、3 - - MIL-V-18318B 3.10.2 - Pipe threads shall be in accordance with MIL-P-7105. 3.11 Color - The color of the valve exterior shall be green, approx- imately matching color number 14110 of FED-STD-595. 3.12 Finish - 3.12.1 Aluminum and aluminum alloys -Aluminum and aluminum alloys shall be anodized

33、in accordance with MIL-A-8625 or MIL-C-5541. 3.13 Degreaeing - All parts of the valve shall be degreased using a vapor phase degreaser in accordance with O-9.-236 OF 0-T-634. Ultrasonics may be used in conjunction with vapor degreasing for the cleaning of components. After completion of the cleaning

34、 and when assembled, General Electric Type H Leak Detector or equivalent Halide testing apparatus shall be used to determine the absence of the cleaning compound. 3.14 Identification of product - The valves shall be marked for identi- fication in accordance with MIL-STD-130, except that the Federal

35、Stock Number shall be omitted from the nameplate. 3.14.1 Nameplate - The following Wormation shall be provided on the nameplate: VALVE, PRESSURE REGULATING, OXYGEN SYSTEM Specification MIL-V-18318B Contract or Order No. Manufacturers Part No. Manufacturers name or trade-mark 3.15 Workmanship - The v

36、alves shall be uniform in quality and shall be free from irregularitfes, defects, or foreign matter which could adversely affect safety, performance, reliability, or durability. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection - Unless otherwise specified in the contract or purchaee

37、 order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the in

38、spections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. . 8 il Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-L3LB 48 979990b 0273394 5 U MIL-V-18

39、318B 4.2 Classification of inspection - The examination and testing of the valves shall be classified as follows: Qualification inspection - Qualification inspection consists of examinations and tests performed on samples submitted for approval as qualified products. First article inspection - First

40、 article inspection consists of examinations and tests performed on- samples which are representative of thnie production item after award of a contract to determine that the production item meets the requirements of this specification. Quality conformance inspection - Quality conformance inspection

41、 consists of examinations and tests performed on individual products or lots to determine conformance of the products or lots with the requirements set forth in this specification. 4.3 Qualification inspection - Qualification inspection shall consist of all the examinations and tests of this specifi

42、cation. 4.3.1 Qualification samples - Qualification samples shall consist of two valves. The qualification samples shall be forwarded to the Supply Officer, Naval Air Engineering Center, Philadelphia, Pennsylvania 19112, Attention: Director, Aerospace Crew Equipment Laboratory. The samples shall be

43、plainly identified by securely attached durable tags marked with the following information: Sample submitted by (name) (date) for qualification inspection in accordance with the requirements of MIL-V-18318B and number under authorization (reference authorizing letter and number, see 6.4) 4.4 First a

44、rticle inspection - First article inspection shall consist of the examinations and tests deemed necessary by the testing activity. 4.4.1 First article samples - 4.4.1.1 Applicable to the Naval Air Systems Command - Unless other- wise specified, as soon as practicable after award of a contract or ord

45、er, the manufacturer shall submit two valves. The samples shall be representative of the construction, workmanship, components, and materials to b used during production. When a 9 - I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-183386 48 79

46、79706 0273395 7 MIL-V-18318B .-. contractor is in continuous production of these valves from contract to contract, submission of further first article samples on the new contract may be waived at the discretion of the procuring activity. Approval of the first article samples or the waiving of the fi

47、rst article inspection does not preclude the requirements of submitting to the quality conformance inspection. The first article samples sliall be forwarded to the Supply Officer, Naval Air Engineering Center, Philadelphia, Pennsylvania 19112, Attention: Director Aerospace Crew Equipment Laboratory,

48、 OF to a laboratory designated by the procuring activity .(see 6.2). The first article samples sha!l be plainly identified by securely attacheddusable tags marked with the following inforiliation: Sample submitted by (name) (date) for first article inspection in accordance with the requirements of M

49、IL-V-18318B under contract no. 4.4.1.1.1 Upon completion of the first article inspection, all the applicable inspection reports and when applicable, recommendations and cominents pertinent for use in monitoring production shall be forwarded to the Government quality control repre- sentative. One approved valve shall be returned to the manufacturer for use in monitorin