NAVY MIL-V-81523 A (2)-1973 VEST SURVIVAL EQUIPMENT TYPE SV-2A《SV-2A型救生衣》.pdf

1、Amendment-2 7 Bovember 1973 .- SUPERSEDING Amendmen t-1 23 February 1972 MILITARY SPECIFICATION VEST, SURVIVAL, TYPE SV-2B This amendment forms a part of Military Specification MIL-S-81523A(AS), dated 17 January 1969, and has been approved by the Naval Air Systems Command, Depart- ment of the Navy.

2、This amendment deletes “EQUIPMENT“ from the title and changes “Type SV-2At to “Type SV-2B“ wherever they appear in this specification. Page 1 S PECIFICA TIONS : (a) Under “Federal“ delete “PPP-B-636If and add: “V-T-295 Thread, Nylon“ (b) Add the following new category: “Mi litarx MIL-B-17757 Box, Fi

3、ber, Corrugated (Moduiar Sizes)“ Bottom of the page, lower right hand corner: Change “FSC 8475“ to “FSC 8415. I Page 2 DRAWINGS: Under “Naval Air Systems Command“ add: “67A100D9 Securing Belt Assembly, Type SV-2B Survival Equipment Vest 3.3.1-Cut edges: Delete the last sentence and substitute “The c

4、ut edges of the nylon duck cloth, except those that are completely covered by the nyton binding tape, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-8L523A (2) 84 W 777770b 0446453 T W .F BIIL-V- 8 1 5 2 3A( AS) Amendment-2 Page 2 (Continued)

5、hook and pile fastener tapes, or are completely encased by the seam construction, shall be overedged stitched (serged). Page 3 Top of the page: (a) Line 3: After inch add “The thread for all the overedge stitching shall conform to V-T-295, Type III, Size B, Class 1, Color Sage Green. It (b) Line 4:

6、Change “6 to 8 stitches per inch“ to “8 to 10 stitches per inch. 3.3.2.1 Sewing, line 3: After “inchtt add “For stitching 1/16 inch from the seam edge, the tolerance shall be plus or minus 1/32 inch, 3.3.2.2 Bartacking: Delete in its entirety and substitute: “3.3.2.2 Bartacking - A 1/2 inch long bar

7、tack shall contain a minimum of 28 stitches. A 3/4-inch bartack shall contain a minimum of 42 stitches. The location and length of the bartacks shall conform to the applicable drawings, If 3.4 Color line 2: After “intt add “3.3.2 and“. -9 3.5 Dimensions, at the end of the paragraph: Add “Each pocket

8、 shall be capa- ble of housing its intended survival equipment. 3.7 Workmanship, line 7: After “stain“ add “Drill holes shall be not greater than 1/16 inch in diameter and shall be covered by the component assemblies. I Page 5 4.5.1.1 Vests: (a) Line 3: After ttspecificationtt add “In addition, the

9、radio, mirror, strobe light, shroud knife, pistol, knife, flare gun, and whistle pockets and sheath shall be examined for fit with the Defense Supply Agency Gage Number 610 (see 6.4). I (b) Line 4: After Witt add “and IIIA“. Page 2 of 4 Provided by IHSNot for ResaleNo reproduction or networking perm

10、itted without license from IHS-,-,-MIL-V-8152.3A( AS) Amenclment- 2 PARAGRAPH REQULREMENT I METHOD Page 6 TABLE I, SAMPLE SIZE, ACCEPTANCE CRITERIA, EXAMINATIONS, AND SAMPLE SIZE TESTS OF THE VESTS: Add the following new horizontal column: 4.5.1. lf Table IIIA, and 4.5.2 INSPECTION Inspection Level

11、S-2 “Fit examination 3.5 ACCEPTANCE CRITERIA An acceptable qualiq level of 2.5 defects per 100 units“ TABLE II, CLASSIFICATION OF DEFECTS FOR THE VISUAL EXAMINATION OF THE VESTS: (a) Page 6, under “GENERAL“, defect line 1: After “hole“ add “except drill holes. I* (b) Page 7, under “GENERAL (Continue

12、d)“ add the following new defect: “1. Any drill hole more than 1/16 inch in diameter or not covered by any attached component“. Insert I%“ in the MINOR A coliunn. (c) Page 8, under “METALLIC COMPONENTS add the following new defect: Irj. Any dot on any securing belt snap fastener not positioned as sp

13、ecified in 67A100D9“. Insert “X“ in the MAJOR column. Page 11 Add the following new table: “TABLE IIIA LIST OF DEFECTS FOR FIT EXAMINATION OF THE POCKETS Fit of the applicable gage in the radio, mirror, strobe light, shroud knife, pistol, . knife, flare gun, and whistle pockets and sheath. DEFECT An

14、y pocket too small to accommodate the respective gage with the pocket in the closed position shall be enumerated as a fit exam ination defect.“ Page 3 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-BL523A (2) B4 m 979990b 044b453 3 m, * r

15、l MIL-V-81523A(AS) Amendment-2 Page. 12 4.5.2 Procedure for measuring, at the end of the paragraph: Add “The gages shall be inserted into their respective pockets, the pockets shall be closed, and the fit of the gages observed. II 5.1.1 Level A, line 5: Delete “13 by 9 inches“ and substitute “11-3/4

16、 by 7-1/2 inches“. Page 13 5.2.1 Level A: (a) Line 1: Change “5.1“ to “5.1. ltt, (b) Delete the last sentence 5. 2.2 Level B: Delete in its entirety and substitute: “5.2.2 Level B - Twenty vests, packaged as specified in 5.1.1, shall be packed flat, two in length, two in width, and five in depth, wi

17、thin a fiberboard shipping container conforming to MIL-B-17757, Type CF, Domestic Class, Variety SW, Grade 200, Size 3A. The top and bottom of the contents of each shipping container shall be completely covered with a sheet of 30 pound minimum basis weight kraft paper con- forming to UU-P-268, Grade

18、 B. The container shall be assembled, closed, and reinforced in accordance with MIL-B-17757, except that metal fasteners or stitches shall not be used. All the seams, corners, and manufacturers joints shall be sealed with the tape conforming to PPP-T-45, Type III, Grade A, B, or C. The body joint an

19、d the top and bottom flaps shall be glued together as specified in MIL-B-17757. Page 14 Add the following new paragraph: “6.4 Fit examination gage - The Defense Supply Agency Gage Number 610 re- quired by 4.5.1.1 will be supplied by the contracting officer. The gage shaii consist of eight parts, radio, mirror, strobe light, shroud knife, pistol, knife, flare gun, and whistle. Preparing activity: (Project No. 8415-N906) Navy - AS * U. S. GOVERNMENT PRINTING OFFICE: 1974 -713- 152/4228 Page 4 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-