NAVY UFGS-09 29 00-2011 GYPSUM BOARD《石膏板》.pdf

1、*USACE / NAVFAC / AFCESA / NASA UFGS-09 29 00 (May 2011)-PREPARING ACTIVITY: NAVFAC SupersedingUFGS-09 29 00 (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2011*SECTION TABLE OF CONTENTSDIVISION 09 - FINISHESSECTION 09 29 00GYPSUM BOARD05/11PAR

2、T 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 SUSTAINABLE DESIGN CERTIFICATION1.4 DELIVERY, STORAGE, AND HANDLING1.4.1 Delivery1.4.2 Storage1.4.3 Handling1.5 ENVIRONMENTAL CONDITIONS1.5.1 Temperature1.5.2 Exposure to Weather1.5.3 Temporary Ventilation1.6 SUSTAINABLE DESIGN REQUIREMENTS1.6.1 Local/Regio

3、nal Materials1.6.2 Environmental Data1.7 QUALIFICATIONS1.8 SCHEDULINGPART 2 PRODUCTS2.1 MATERIALS2.1.1 Gypsum Board2.1.1.1 Regular2.1.1.2 Foil-Backed2.1.1.3 Type X (Special Fire-Resistant)2.1.2 Gypsum Backing Board2.1.2.1 Regular2.1.2.2 Foil-Backed2.1.2.3 Type X (Special Fire-Resistant)2.1.3 Regular

4、 Water-Resistant Gypsum Backing Board2.1.3.1 Regular2.1.3.2 Type X (Special Fire-Resistant)2.1.4 Glass Mat Water-Resistant Gypsum Tile Backing Board2.1.4.1 Regular2.1.4.2 Type X (Special Fire-Resistant)SECTION 09 29 00 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted withou

5、t license from IHS-,-,-2.1.5 Glass Mat Covered or Reinforced Gypsum Sheathing2.1.5.1 Glass Mat Covered or Reinforced Gypsum Sheathing Sealant2.1.6 Impact Resistant Gypsum Board2.1.6.1 Structural Failure Test2.1.6.2 Indentation Test2.1.7 Predecorated Gypsum Board2.1.8 Cementitious Backer Units2.1.9 J

6、oint Treatment Materials2.1.9.1 Embedding Compound2.1.9.2 Finishing or Topping Compound2.1.9.3 All-Purpose Compound2.1.9.4 Setting or Hardening Type Compound2.1.9.5 Joint Tape2.1.10 Fasteners2.1.10.1 Nails2.1.10.2 Screws2.1.10.3 Staples2.1.11 Adhesives2.1.11.1 Adhesive for Fastening Gypsum Board to

7、Metal Framing2.1.11.2 Adhesive for Fastening Gypsum Board to Wood Framing2.1.11.3 Adhesive for Laminating2.1.12 Gypsum Studs2.1.13 Shaftwall Liner Panel2.1.14 Accessories2.1.15 Asphalt Impregnated Building Felt2.1.16 WaterPART 3 EXECUTION3.1 EXAMINATION3.1.1 Framing and Furring3.1.2 Gypsum Board and

8、 Framing3.1.3 Masonry and Concrete Walls3.2 APPLICATION OF GYPSUM BOARD3.2.1 Application of Single-Ply Gypsum Board to Wood Framing3.2.2 Application of Two-Ply Gypsum Board to Wood Framing3.2.3 Adhesive Nail-On Application to Wood Framing3.2.4 Semi-Solid Gypsum Board Partitions3.2.5 Solid Gypsum Boa

9、rd Partitions3.2.6 Adhesive Application to Interior Masonry or Concrete Walls3.2.7 Application of Gypsum Board to Steel Framing and Furring3.2.8 Arches and Bending Radii3.2.9 Gypsum Board for Wall Tile or Tile Base Applied with Adhesive3.2.10 Exterior Application3.2.11 Glass Mat Covered or Fiber Rei

10、nforced Gypsum Sheathing3.2.12 Floating Interior Angles3.2.13 Control Joints3.2.14 Application of Foil-Backed Gypsum Board3.2.15 Application of Predecorated Gypsum Board3.2.16 Application of Impact Resistant Gypsum Board3.3 APPLICATION OF CEMENTITIOUS BACKER UNITS3.3.1 Application3.3.2 Joint Treatme

11、nt3.4 FINISHING OF GYPSUM BOARD3.4.1 Uniform Surface3.4.2 Metal Trim for Predecorated Gypsum Board3.5 SEALING3.5.1 Sealing for Glass Mat or Reinforced Gypsum Board Sheathing3.6 FIRE-RESISTANT ASSEMBLIESSECTION 09 29 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted withou

12、t license from IHS-,-,-3.7 PATCHING3.8 SHAFTWALL FRAMING3.9 WASTE MANAGEMENT- End of Section Table of Contents -SECTION 09 29 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-09 29 00 (May 2011)-PREPARING

13、ACTIVITY: NAVFAC SupersedingUFGS-09 29 00 (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April 2011*SECTION 09 29 00GYPSUM BOARD05/11*NOTE: This guide specification includes the requirements for gypsum board, cementitious backer units, and accessorie

14、s intended for use in drywall construction.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting,

15、 or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and

16、should be submitted as a Criteria Change Request (CCR).Reference Section 05 40 00 COLD-FORMED METAL FRAMING for load bearing studwork. Reference Section 09 22 00 SUPPORTS FOR PLASTER AND GYPSUM BOARD for non-loadbearing studs, furring and ceiling suspension systems.*NOTE: On the drawings, show:1. Lo

17、cations of each type of gypsum board, backing board and cementitious backer units, using same terminology as in the specification.2. Locations and UL or GA design numbers for fire rated gypsum board and cementitious backer unit assemblies.3. Locations of asphalt impregnated building felt SECTION 09

18、29 00 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-if gypsum sheathing is used or if cementitious backer units are used in wet areas.*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the

19、 guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically plac

20、e the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process

21、.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI A108.11 (1992; Reaffirmed 2005) Specifications for Interior Installation of Ceme

22、ntitious Backer UnitsASTM INTERNATIONAL (ASTM)ASTM C 1002 (2007) Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel StudsASTM C 1047 (2010a) Standard Specification for Accessories for Gypsum Wallboa

23、rd and Gypsum Veneer BaseASTM C 1177/C 1177M (2008) Standard Specification for Glass Mat Gypsum Substrate for Use as SheathingASTM C 1178/C 1178M (2008) Standard Specification for Glass Mat Water-Resistant Gypsum Backing PanelASTM C 1396/C 1396M (2009a) Standard Specification for Gypsum BoardSECTION

24、 09 29 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASTM C 475/C 475M (2002; R 2007) Joint Compound and Joint Tape for Finishing Gypsum BoardASTM C 514 (2004; R 2009e1) Standard Specification for Nails for the Application of Gypsum BoardA

25、STM C 557 (2003; R 2009e1) Adhesives for Fastening Gypsum Wallboard to Wood FramingASTM C 840 (2008) Application and Finishing of Gypsum BoardASTM C 954 (2010) Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in.

26、(2.84 mm) in ThicknessASTM C1629/C1629M (2006) Standard Classification for Abuse-Resistant Nondecorated Interior Gypsum Panel Products and Fiber-Reinforced Cement PanelsASTM D 1037 (2006a) Evaluating Properties of Wood-Base Fiber and Particle Panel MaterialsASTM D 1149 (2007) Standard Test Method fo

27、r Rubber Deterioration - Surface Ozone Cracking in a ChamberASTM D 226/D 226M (2009) Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and WaterproofingASTM D 2394 (2005; R 2011) Simulated Service Testing of Wood and Wood-Base Finish FlooringASTM D 412 (2006ae2) Standard Test

28、 Methods for Vulcanized Rubber and Thermoplastic Elastomers - TensionASTM D 5420 (2010) Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Strike Impacted by a Falling Weight (Gardner Impact)ASTM D 624 (2000; R 2007) Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elas

29、tomersASTM E 2129 (2005) Standard Practice for Data Collection for Sustainability Assessment of Building ProductsASTM E 695 (2003; R 2009) Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact LoadingSECTION 09 29 00 Page 6Provided by IHSNot for ResaleNo reproduction or netwo

30、rking permitted without license from IHS-,-,-ASTM E 84 (2010b) Standard Test Method for Surface Burning Characteristics of Building MaterialsGREENGUARD ENVIRONMENTAL INSTITUTE (GEI)GEI Greenguard Standards for Low Emitting ProductsGYPSUM ASSOCIATION (GA)GA 214 (2007) Recommended Levels of Gypsum Boa

31、rd FinishGA 216 (2010) Application and Finishing of Gypsum Panel ProductsGA 224 (2008) Installation of Predecorated Gypsum BoardGA 253 (2007) Application of Gypsum SheathingGA 600 (2009) Fire Resistance Design ManualSCIENTIFIC CERTIFICATION SYSTEMS (SCS)SCS Scientific Certification Systems (SCS)Indo

32、or AdvantageU.S. GREEN BUILDING COUNCIL (USGBC)LEED (2002; R 2005) Leadership in Energy and Environmental Design(tm) Green Building Rating System for New Construction (LEED-NC)UNDERWRITERS LABORATORIES (UL)UL Fire Resistance (2011) Fire Resistance Directory1.2 SUBMITTALS*NOTE: Review Submittal Descr

33、iption (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires

34、Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.SECT

35、ION 09 29 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the app

36、roving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes foll

37、owing the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“

38、 designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-03 Product D

39、ataCementitious backer unitsGlass Mat Water-Resistant Gypsum Tile Backing BoardWater-Resistant Gypsum Backing BoardGlass Mat Covered or Reinforced Gypsum SheathingGlass Mat Covered or Reinforced Gypsum Sheathing SealantImpact Resistant Gypsum BoardAccessoriesSubmit for each type of gypsum board and

40、for cementitious backer units.CertificationGypsum Board; (LEED)Submit documentation indicating percentage of post-industrial and post-consumer recycled content per unit of product. Indicate relative dollar value of recycled content products to total dollar value of products included in project. Adhe

41、sives; (LEED)Joint Treatment MaterialsSubmit manufacturers product data, indicating VOC content. Local/Regional Materials; (LEED)SECTION 09 29 00 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Documentation indicating distance between manufact

42、uring facility and the project site. Indicate distance of raw material origin from the project site. Indicate relative dollar value of local/regional materials to total dollar value of products included in project. Environmental DataSD-04 SamplesPredecorated gypsum board; G; G, _Submit for each colo

43、r and pattern of predecorated gypsum board. Where colors are not indicated, submit color selection samples of not less than eight of the manufacturers standard colors.SD-07 CertificatesAsbestos Free Materials; G; G, _Certify that gypsum board types, gypsum backing board types, cementitious backer un

44、its, and joint treating materials do not contain asbestos.SD-08 Manufacturers InstructionsMaterial Safety Data SheetsSD-10 Operation and Maintenance DataManufacturer maintenance instructionsWaste ManagementSD-11 Closeout SubmittalsLocal/Regional Materials; (LEED)LEED documentation relative to local/

45、regional materials credit in accordance with LEED Reference Guide. Include in LEED Documentation Notebook.Gypsum Board; (LEED)LEED documentation relative to recycled content credit in accordance with LEED Reference Guide. Include in LEED Documentation Notebook.Adhesives; (LEED)LEED documentation relative to low emitting materials credit in accordance with LEED Reference Guide. Include in LEED Documentation Notebook.1.3 SUSTAINABLE DESIGN CERTIFICATIONP