NEMA C78 1430-1997 Electric Lamps - Slide Projector Lamps Condensing Dichroic 1 65-in (42 mm) Integral Reflector Rim Reference Tungsten-Halogen Lamps with GX5 3 Bases《电灯 幻灯放映灯 带GX5.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.1430-1997 (R2016)Electric Lamps Slide Projector Lamps, Condensing, Dichroic, 1.65-in. (42 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GX5.3 BasesANSI C78.1430-1997 (R2009, R2016) Page 1 2016 Nation

2、al Electrical Manufacturers Association C78.1430-1997 (R2009, R2016) American National Standard for Electric Lamps Slide Projector Lamps, Condensing, Dichroic, 1.65-in. (42 mm), Integral Reflector, Rim Reference Tungsten-Halogen Lamps with GX5.3 Bases Secretariat: National Electrical Manufacturers A

3、ssociation Approved: February 26, 2016 American National Standards Institute, Inc. ANSI C78.1430-1997 (R2009, R2016) Page 2 2016 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engage

4、d in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which the document contained herei

5、n is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the development

6、of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or

7、 other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or

8、completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by vi

9、rtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this doc

10、ument should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sou

11、rces, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for s

12、afety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C78.1430-1997 (R2009, R2016) Page i 2016 Na

13、tional Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met by the stan

14、dards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly, and materially affected interes

15、ts. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respect preclud

16、e anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National Standards In

17、stitute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute,

18、 Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require that action

19、be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North

20、 17thStreet, Suite 900 Rosslyn, Virginia 22209 2016 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International a

21、nd Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ANSI C78.1430-1997 (R2009, R2016) Page ii 2016 National Electri

22、cal Manufacturers Association Foreword (This foreword is not part of American National Standard C78.1430) Suggestions for improvement of this standard should be submitted to: Secretariat C78 National Electrical Manufacturers Association 1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 This s

23、tandard was processed and approved by Accredited Standards Committee on Electric Lamps, C78. Committee approval of the standard does not necessarily imply that all committee members voted for that approval. ANSI C78.1430-1997 (R2009, R2016) Page iii 2016 National Electrical Manufacturers Association

24、 CONTENTS Foreword . ii 1 Scope.1 2 Normative reference 1 3 Ratings1 4 Performance .2 5 Restrictions 2 6 Cautionary notice .2 7 Physical characteristics.2 8 Test procedures. 3 Annex A (Normative)4 ANSI C78.1430-1997 (R2009, R2016) Page iv 2016 National Electrical Manufacturers Association ANSI C78.1

25、430-1997 (R2009, R2016) Page 1 2016 National Electrical Manufacturers Association 1 Scope This standard consolidates the lamps commonly used for slide projectors into a single standard. The lamps contained in this standard are not to be considered as interchangeable, although physically they will al

26、l fit the common GX5.3 sockets. The photometry of each lamp is dependent upon the system for which it was designed and on the system in which it is used. A sample system and representative photometric values are found in the Annex. 2 Normative References The following standards contain provisions wh

27、ich, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the po

28、ssibility of applying the most recent editions of the standards indicated below. ANSI C78.1417-1997 Electric Lamps, Dimensions and centering system for projection lamps1.65 inch integral reflector projection lamps with GX5.3 or GY5.3 bases ANSI C78.1450-1983 (R1994) Electric Lamps, Incandescent Proj

29、ection Lamps, Method of Life Testing ANSI C81.61-1990 (R1996) Electric Lamps, Electric Lamp Bases ANSI IT7.201-1991 Audio Visual SystemsSlide Projectors and Filmstrip ProjectorsIllumination Test IEC 682-1980 Standard Method of Measurement of Pinch Temperature of Quartz-Tungsten-Halogen Lamps 3 Ratin

30、gs This standard includes the following lamps: EXR, EXW, EXY, and FHS. Table 1 Lamp Ratings ANSI Designation Watts Volts Life (hrs.) Working Distance (mm) Correlated Color Temperature (K) EXR EXW EXY FHS 300 300 250 300 82 82 82 82 35 15 200 70 152.4 152.4 152.4 152.4 3350 3450 3200 3300 ANSI C78.14

31、30-1997 (R2009, R2016) Page 2 2016 National Electrical Manufacturers Association 4 Performance Table 2 Representative Values ANSI Designation Nominal Screen Illumination (Lumen) Nominal Comer/Center Ratio (%) EXR EXW EXY FHS 1000 1150 625 800 65 60 65 70 NOTEThe representative values shown were obta

32、ined with a typical projection system as described in the Annex. Manufacturers may rate their products based on a different projection system, consult the manufacturer for details. 5 Restrictions Operating PositionBase down to horizontal plus 15 degrees Temperature Limits . 400 degrees C maximum on

33、seals 250 degrees C minimum on bulb Protective Shield See Cautionary Notice 6 Cautionary Notice To assure maximum safety during handling and use of the subject lamps, the following notices should be observed: 1 Tungsten-halogen lamps operate at high temperature and at internal gas pressures above at

34、mospheric pressure. Consequently, a lamp could shatter. Certain lamps may also emit some amount of ultraviolet radiation. Therefore, a suitable protective shield, screening technique, or both shall be used with the luminaire to protect people and surroundings from both hazards. 2 Always read and obs

35、erve the information contained in the lamp manufacturers caution notice. 7 Physical Characteristics Base Specifications: GX5.3: see ANSI C81.61 Dimensions: General dimensions for this type of lamp are covered in ANSI C78.1417. ANSI C78.1430-1997 (R2009, R2016) Page 3 2016 National Electrical Manufac

36、turers Association 8 Test Procedures Life . Open rack, horizontal burning position with cooling to maintain temperature limits in accordance ANSI C78.1450. Illumination . See ANSI IT7.201. Seal Temperature . Measurement procedure is defined in IEC 682. Operating Temp . Standard method of measuring o

37、ther lamp operating temperatures (bulb and base) are under consideration. ANSI C78.1430-1997 (R2009, R2016) Page 4 2016 National Electrical Manufacturers Association ANNEX A (Normative) Component Description 1-Lamp Designation EXR EXW EXY FHS 2-Diaphragm (dia. N) 31.75mm 31.75mm 31.75mm 31.75mm 3-He

38、at Absorbing Glass 4-Biconvex Condenser Lens Focal Length 70.4mm 70.4mm 70.4mm 70.4mm 5-Film Plane: Aperture Size 23.01mm x 34.11 mm 23.01mm x 34.11mm 23.01mm x 34.11mm 23.01mm x 34.11mm 6-Projection Lens Focal Length f/no. 102mm f/2.8 102mm f/2.8 102mm f/2.8 102mm f/2.8 7-Projected Image Plane Imag

39、e Size 685mm x 1016mm 685mm x 1016mm 685mm x 1016m 685mm x 1016mm Reference L 152.4mm 152.4mm 152.4mm 152.4mm M 23.6mm 23.6mm 23.6mm 23.6mm Figure A-1 Typical Component Layout and Dimensions for Projection Lamp System NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION 1300 NORTH 17TH STREET, SUITE 900 ROSSLYN. VA 22209www.NEMA.orgTO ORDER ADDITIONAL NEMA STANDARDS VISITWWW.GLOBAL.IHS.COM OR CALL 1-800-854-7179/1-303-397-79565612_0514TB