NEMA C78 5-2017 Electric Lamps Specifications for Performance of Self-Ballasted Compact Fluorescent Lamps.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.5-2017Electric Lamps Specifications for Performance of Self-Ballasted Compact Fluorescent LampsANSI C78.5-2017 Page 1 2017 National Electrical Manufacturers Association ANSI C78.5-2017 American National Standard for Elec

2、tric Lamps Specifications for Performance of Self-Ballasted Compact Fluorescent Lamps Secretariat: National Electrical Manufacturers Association Approved: December 21, 2017 American National Standards Institute, Inc. ANSI C78.5-2017 Page 2 2017 National Electrical Manufacturers Association NOTICE AN

3、D DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating i

4、n the development of this document. ANSI standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest

5、in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments c

6、ontained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or relia

7、nce on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA

8、does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or ent

9、ity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given cir

10、cumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance w

11、ith the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is so

12、lely the responsibility of the certifier or maker of the statement. ANSI C78.5-2017 Page i 2017 National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by the American National Standards Institute, Inc. (ANSI) that the

13、requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Sta

14、ndards Review, substantial agreement has been reached by directly, and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made towar

15、d their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide

16、 to aid the manufacturer, the consumer, and the general public. ANSI does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in

17、the name of the ANSI. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of ANSI require that action be taken periodically to rea

18、ffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing ANSI. Published by National Electrical Manufacturers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209 2017 National Electric

19、al Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication ma

20、y be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ANSI C78.5-2017 Page ii 2017 National Electrical Manufacturers Association Foreword (This foreword is not part of American National

21、Standard C78.5-2017) Suggestions for improvement of this standard should be submitted to: Secretariat C78 National Electrical Manufacturers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia 22209 This standard was processed and approved by Accredited Standards Committee on Electric Lam

22、ps, C78. Committee approval of the standard does not necessarily imply that all committee members voted for that approval. ANSI C78.5-2017 Page iii 2017 National Electrical Manufacturers Association CONTENTS Foreword . ii I Scope. . 1 2 Normative References . . 1 3 Definitions . 2 3.1 General . 2 3.

23、2 Minimum Starting Temperature. 2 4. Requirements . . 2 4.1 General . 2 4.2 Marking . 2 4.3 Other Markings . 2 4.4 Electro-magnetic interference . 2 4.5 Performance . 2 4.6 Life test 3 4.7 Power Quality . 3 4.8 Lamp current operating frequency . .3 4.9 Line transient requirements . 3 5 Selection of

24、Test Samples. 3 6 Tests 3 6.1 General . 3 6.2 Power Supply . 3 6.3 Electrical Instruments . 3 6.4 Life test 4 Annex A (Informative) Bibliography . 5 ANSI C78.5-2017 Page iv 2017 National Electrical Manufacturers Association ANSI C78.5-2017 Page 1 2017 National Electrical Manufacturers Association 1

25、Scope This standard specifies the performance requirements together with the test methods and conditions required to show compliance of self-ballasted compact fluorescent lamps up to 60 watts which are intended for domestic and similar general lighting purposes. Such lamps shall have a rated input v

26、oltage of 120 or 277 volts at 60 Hz and an Edison screw base. Globe and reflector types are excluded. 2 Normative References The following publications contain provisions which, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the

27、editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the publications indicated below. ANSI C78.375A American National Standard fo

28、r Electric LampsFluorescent LampsGuide for Electrical Measurements ANSI C78.30 American National Standard for Electric LampsProcedure for Use in Preparation of Lamp Space Drawings CIE Publication 13.3, Second Edition Method of Measuring and Specifying Color Rendering Index of Light Sources CIE Publi

29、cation 15.2 Colorimetry IEC 60969:2016 Self-Ballasted Compact Fluorescent Lamps for General Lighting ServicesPerformance Requirements IES LM-65 Approved Method for Life Testing of Compact Fluorescent Lamps IES LM-66 Approved method for the Electrical and Photometric Measurements of Single-Ended Comp

30、act Fluorescent Lamps UL 1993 Standard for Self-Ballasted Lamps and Lamp Adapters ANSI C82.13 American National Standard for Lamp BallastsDefinitions for Fluorescent Lamps and Ballasts ANSI C82.77-5 American National Standard for Lighting EquipmentVoltage Surge Requirements ANSI C82.77-10 American N

31、ational Standard for Lighting EquipmentHarmonic Emission LimitsRelated Power Quality Requirements NEMA 410 Performance Testing for Lighting Controls and Switching Devices with Electronic Drivers and Discharge Ballasts Energy Star-Lamps V2.0 Lamps Specification ANSI C78.5-2017 Page 2 2017 National El

32、ectrical Manufacturers Association 3 Definitions 3.1 General ANSI C82.13 and IEC 60969, clause 3, contain related definitions. Any standards referenced in those definitions should be considered as normative for the standard. Definitions found in ANSI C82.13 or this standard shall have preference ove

33、r IEC 60969 for any common terms. Other definitions used in this standard follow. 3.2 Minimum Starting Temperature The minimum starting temperature is the minimum temperature at which the lamp will reliably start. 4 Requirements 4.1 General Self-ballasted compact fluorescent lamps shall be so constr

34、ucted that, in normal use, they are without danger to the user and the general surroundings. Electrical and photometric performance of compact fluorescent lamps can be appreciably affected by drafts, ambient temperature, and burning position. For proper measurements of these characteristics, the req

35、uirements for ambient conditions and lamp stabilization in ANSI C78.375 shall be met. Photometric procedures are specified in IES LM-66. The lamps shall be stabilized base-up at 25 1C. 4.2 Marking The unit shall be marked in accordance with UL1993. The performance marking requirements in IEC 60969,

36、clause 4, Table 1 shall be applied. 4.3 Other Markings 4.3.1 The unit shall include instructions per UL1993 if so required. 4.4 Electro-Magnetic Interference Units with electronic high-frequency circuits shall comply with FCC regulations, Title 47 of the US Code of Federal Regulations, Part 18 for C

37、onsumer equipment. For units with electronic high-frequency circuits operating below 1.705 MHz, radiated measurements shall be made from 30 MHz to 1 GHz and be under the limits specified in FCC Part 18.305c. 4.5 Performance The performance requirements of IEC 60969, clause 6 shall be applied with th

38、e deviations below. Test procedures in IEC 60969, Annex B (starting time), Annex C (run-up time), and Annex E (low temperature and low supply voltage starting) are applicable. 4.5.1 Compliance to UL 1993 shall be required instead of IEC 60968. 4.5.2 Initial power shall be measured according to IES L

39、M-66 instead of IEC 60969, Annex A. 4.5.3 Displacement and distortion factor requirements do not apply. See clause 4.7 for power quality requirements. 4.5.4 Initial luminous flux and lumen maintenance shall be measured according to IES LM-66 instead of IEC 60969, Annex D. 4.5.5 If dimensional equiva

40、lence with incandescent lamps is claimed then lamps shall comply with ANSI C78.30 instead of IEC 60630. 4.5.6 Lumen maintenance shall conform to Energy Star-Lamps. ANSI C78.5-2017 Page 3 2017 National Electrical Manufacturers Association 4.5.7 Lifetime and premature lamp failure (if claimed) shall b

41、e measured according to IES LM-65 instead of IEC 60969, Annex G. 4.5.8 Inrush current shall conform to NEMA 410, instead of IEC 60969, Annex H. 4.5.9 The test for switching withstand shall use the specification in Energy Star-Lamps. 4.6 Life Test Life testing shall be done in accordance with the req

42、uirements of IES LM-65. 4.7 Power Quality The requirements for this product as specified in ANSI C82.77-10 shall be met. 4.8 Lamp Current Operating Frequency In order to limit incompatibility with infrared remote controls, the lamp current operating frequency shall be greater than 40 kHz for units w

43、ith electronic high-frequency circuits. This frequency limit shall be met under all stable normal operating conditions including dimming. 4.9 Line Transient Requirements Electronic high-frequency ballasts are more susceptible to line transients than line frequency magnetic ballasts. Therefore, trans

44、ient protection shall be included when lamps use electronic ballasts. The requirement for this transient protection is ANSI C82.77-5. 5 Selection of Test Samples 5.1 Lamps shall be selected to ensure proper representation of the current design. 5.2 Sample selection shall conform to IEC 60969:2016, c

45、lause 6.2. It is prudent to select one or more additional samples to serve as potential replacements in the event of breakage or if the samples become defective during the test for reasons not connected to the test, or if one or more samples exhibit abnormal behavior or fail to stabilize. 6 Tests 6.

46、1 General 6.1.1 Each test shall be performed at least once with each of the selected samples. Each sample shall meet the described test criteria . 6.1.2 If a sample breaks or becomes defective for reasons not as a result of the testing; the sample shall be discarded. Similarly, if a unit fails to st

47、abilize or exhibits abnormal behavior, the lamp shall be discarded. Testing shall resume with a suitable replacement sample procured and prepared in the same manner as the original sample. The use of replacement samples shall be documented in the test report. 6.2 Power Supply For other than life tes

48、ts, the voltage to the unit under test shall meet the requirements of supply voltage characteristics in ANSI C78.375. 6.3 Electrical Instruments The electrical instruments used in the testing shall meet the requirements for instruments in ANSI C78.375. ANSI C78.5-2017 Page 4 2017 National Electrical Manufacturers Association 6.4 Life Test Tes