NEMA C78 81-2016 Electric Lamps- Double-Capped Fluorescent Lamps- Dimensional and Electrical Characteristics.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C78.81-2016Electric LampsDouble-Capped Fluorescent LampsDimensional and Electrical CharacteristicsANSI C78.81-2016 American National Standard for Electric Lamps Double-Capped Fluorescent Lamps Dimensional and Electrical Char

2、acteristics Secretariat: National Electrical Manufacturers Association Approved: June 29, 2016 American National Standards Institute, Inc. ANSI C78.81-2016 Page ii 2016 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically

3、sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. American National Standards Institute, I

4、nc. (ANSI) standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this p

5、ublication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and

6、guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA dis

7、claims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any particular purposes or needs. NEMA does not undertake to guarantee the pe

8、rformance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perfor

9、m any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other stan

10、dards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEM

11、A does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifi

12、er or maker of the statement. ANSI C78.81-2016 Page iii 2016 National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, conse

13、nsus, and other criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreemen

14、t has been reached by directly, and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence o

15、f an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consu

16、mer, and the general public. The American National Standards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Sta

17、ndard in the name of the American National Standards Institute, Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the Am

18、erican National Standards Institute, Inc., require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Publis

19、hed by National Electrical Manufacturers Association 1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 2016 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Pro

20、tection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of AmericaA

21、NSI C78.81-2016 Page iv 2016 National Electrical Manufacturers Association FOREWORD (This foreword is not part of ANSI C78.81-2016) Suggestions for improvement of this standard should be submitted to the Secretariat, C78 Committee, National Electrical Manufacturers Association, 1300 North 17thStreet

22、, Suite 900, Rosslyn, VA 22209. This standard was processed and approved by Accredited Standards Committee on Electric Lamps, C78, and its work group, C78WG02. Approval of the standard does not necessarily imply that all work group members voted for its approval. This revision supersedes ANSI C78.81

23、-2014. This standard features revisions to: 1. The following datasheets1. 17 Watt, 24-Inch T8, Fluorescent Lamp 7881-ANSI-1001-2 -32. 25 Watt 36 inch T8, Fluorescent Lamp 7881-ANSI-1002-2 -33. 25 Watt, 48-inch T8, Fluorescent Lamp 7881-ANSI-1028-2 -34. 32 Watt, 48-inch T8, Fluorescent Lamp 7881-ANSI

24、-1005-3 -45. 28 Watt, 48-inch T8, Fluorescent Lamp 7881-ANSI-1029-2 -36. 30 Watt, 48-inch T8, Fluorescent Lamp 7881-ANSI-1030-2 -37. 40 Watt, 60-inch T8, Fluorescent Lamp 7881-ANSI-1007-2 -38. 15 Watt, 18-inch T8, Fluorescent Lamp 7881-ANSI-1031-1 -29. 15 Watt, 24-inch T8, Fluorescent Lamp 7881-ANSI

25、-1032-1 -210. 21 Watt, 36-inch T8, Fluorescent Lamp 7881-ANSI-1033-1 -22. Annex D3. Datasheet 7881-ANSI-1501-286- Watt, 96-inch T8, 0.4 A HF Rapid Start Fluorescent Lamp, pg. 115, revision and reformatANSI C78.81-2016 Page v 2016 National Electrical Manufacturers Association CONTENTS Foreword . iv T

26、able of Contents . v PART 1General Information and Requirements 1 1 Scope 1 2 General . 1 3 Definitions . 2 4 Lamp abbreviations . 2 5 Methods of measurement . 2 6 Reference ballasts 2 7 Product drawings 2 8 Application of lamps on more than one type of circuit 3 9 Lamp physical and dimensional requ

27、irements 3 10 Lamp electrical characteristics 5 11 Requirements for ballast design . 6 12 Requirements for luminaire design . 8 PART IILamp Drawings and Dimensioning Principles . 10 PART IIIAnnexes . 11 Annex A (Informative) Guide for Establishing Fluorescent Lamp Abbreviations . 11 Annex B (Informa

28、tive) Guidelines for the Establishment of Wattage Ratings on Lamp Data Sheets. 14 Annex C (Informative) Bibliography . 16 Annex D (Normative) USA Deviations to adopted IEC sheets 17 PART IVLamp Specification Data Sheets 18 1 General Principals for Numbering of Data Sheets 18 2 Data Sheet List and Se

29、quence . 18 3 Deviations to Adopted IEC Data Sheets . 18 Lamp Data Sheets 19-186 ANSI C78.81-2016 Page vi 2016 National Electrical Manufacturers Association ANSI C78.81-2016 Page 1 2016 National Electrical Manufacturers Association PART I General Information and Requirements 1 Scope This standard se

30、ts forth the physical and electrical characteristics of the principal types of fluorescent lamps intended for application on conventional line frequency circuits and electronic high frequency circuits. Some data sheets may specify more than one circuit application. Specifications for the lamp itself

31、 and the interactive features of the lamp and ballast are given. Only double-based lamps of the regular linear shape are included. Single-based lamps, including compact, circular, square, and U-shaped, are found in ANSI C78.901. Lamps for conventional systems relying on auxiliary support from extern

32、al ballasts are described. These lamps are those designed for 60 Hz and/or high frequency operation. Lamp color is not specified herein. Certain lamp types covered in this standard may be similar to those in IEC 60081. However, additional types are included that are used only in North America and ar

33、e not specified in the IEC standard. 1.1 Important Patent Disclaimer At the time of publication, it is possible that some of the elements of this document may be the subject of patent rights. When this standard was approved for publication, the National Electrical Manufacturers Association (NEMA) di

34、d not know of any patent applications, patents pending, or existing patents. NEMA shall not be held responsible for identifying any or all such patent rights. 2 General There are four parts to this standard: Part I Contains requirements and general information. Detailed descriptions, references, and

35、 explanations of the terms used in the lamp data sheets are given. Defines the principles of dimensioning lamps, both as finished lamps and for maximum outline purposes. Part II Contains dimensioning principles and lamp outline drawings. Part III Contains the annexes. Part IV Contains the lamp data

36、sheets for the lamp classes covered in this standard. Sheets adopted from IEC are not included, but a source reference is listed. 2.1 Normative References The following standards contain provisions that, through reference in this text, constitute provisions of this American National Standard. At the

37、 time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI C78.79 American

38、 National Standard for Electric LampsNomenclature for Envelope Shapes Intended for Use with Electric Lamps ANSI C78.180 American National Standard for Electric LampsSpecifications for Fluorescent Lamp Starters ANSI C78.81-2016 Page 2 2016 National Electrical Manufacturers Association ANSI C78.375A A

39、merican National Standard for Electric LampsFluorescent LampsGuide for Electrical Measures ANSI C78.376 American National Standard for Electric LampsSpecifications for the Chromaticity of Fluorescent Lamps ANSI C78.901 American National Standard for Electric LampsElectric LampsSingle-Based Fluoresce

40、nt LampsDimensional and Electrical Characteristics ANSI C78.1195 American National Standard for Electric LampsDouble-capped Fluorescent LampsSafety Specifications ANSI C81.61 American National Standard for Electrical Lamp BasesSpecifications for Bases (Caps) for Electric Lamps ANSI C81.63 American N

41、ational Standard for Gauges for Electric Lamp Bases and Lampholders ANSI C82.1 American National Standard for Lamp BallastsLine Frequency Fluorescent Lamp Ballasts ANSI C82.3 American National Standard for Lamp BallastsReference Ballasts for Fluorescent Lamps ANSI C82.11 American National Standard f

42、or Lamp BallastsHigh Frequency Fluorescent Lamp Ballasts ANSI C82.13 American National Standard for Lamp BallastsDefinitionsfor Fluorescent Lamps and Ballasts ANSI/IEEE 100 The Authoritative Dictionary of IEEE Standards Terms 3 Definitions For related definitions, see ANSI C82.13 and the electrical

43、dictionary ANSI/IEEE 100. 4 Lamp Abbreviations Lamp abbreviations for fluorescent lamps are not officially assigned through any administered designation system. Those used on the data sheets are assigned in accordance with the Guidelines of Annex A. There is no requirement for the use of these abbre

44、viations for lamp marking. For some lamp types, the referenced data sheet has been adopted from IEC publication 60081. These sheets do not contain a lamp abbreviation per Annex A. They are marked with an IEC designation code (ILCOS), but that code is not used in the U.S. 5 Methods of Measurement Ele

45、ctrical measurements necessary to determine the performance of lamps that are defined in this standard shall be made in accordance with the lamp measurements standard (ANSI C78.375). 6 Reference Ballasts Reference ballasts used for measurements of fluorescent lamps shall meet the general requirement

46、s set forth in the reference ballast standard (ANSI C82.3). It should be noted that the reference ballast standard requires a power factor of 0.075 0.005 for all fluorescent reference ballasts, unless otherwise specified on a lamp data sheet. Also note that rapid start reference ballasts called for

47、in this standard include 3.6V cathode heating. 7 Product Drawings The drawings included in Part II are product drawings that show the applications of the various coded dimensions that appear on the data sheets. Drawings are needed only to depict families of ANSI C78.81-2016 Page 3 2016 National Elec

48、trical Manufacturers Association lamps; the particular values vary within a family in accordance with the values on the relevant lamp data sheet. No attempt has been made to provide maximum outline drawings to show the space occupied by the lamps because the need for such has not been established. 8

49、 Application of Lamps on More Than One Type of Circuit Lamp manufacturers may form an industry consensus approving the use of a particular lamp type on more than one type of circuit. In such cases, the lamp data sheet will show the information for all of the appropriate circuits. 9 Lamp Physical and Dimensional Requirements 9.1 Bulb Specifications Each lamp data sheet in Part IV specifies the necessary bulb shape and tube diameter. Bulb shapes are defined in the bulb nomenclature standard (ANSI C79.1). Due to the