NEMA C81 63-2007 Gauges for Electric Lamp Bases and Lampholders.pdf

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C81.63-2007 (R2014)Gauges for Electric LampBases and LampholdersANSI C81.63-2007 (R2014) American National Standard for Gauges for Electric Lamp Bases and Lampholders Secretariat: National Electrical Manufacturers Associatio

2、n Approved December 12, 2014 American National Standards Institute, Inc. 2007 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document a

3、t the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. American National Standards Institute, Inc. (ANSI) standards and guideline publications, of which the document contained herein is

4、one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of co

5、nsensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or othe

6、r damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or compl

7、eteness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue

8、of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document

9、 should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources,

10、 which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety

11、 or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C81.63-2007 (R2014) 2007 National Electrical Man

12、ufacturers Association i American National Standard Approval of an American National Standard requires verification by the American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An

13、 American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agre

14、ement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/

15、he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National Standards Institute, Inc., does

16、not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute, Inc. Requests for i

17、nterpretations should be addressed to the Committee Secretariat referred to on the title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc., require that action be taken periodically to reaf

18、firm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North 17th Street, Suite 900, Ross

19、lyn, Virginia 22209 2007 National Electrical Manufacturers Association. All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright

20、conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America ANSI C81.63-2007 (R2014) ii 2007 National Electrical Manufacturers Association Forewo

21、rd for American National Standard ANSI C81.63-2007 (This foreword is not part of American National Standard ANSI C81.63-2007) In 1990 and 1991 the American National Standards (ANS) for lamp bases, lampholders and gauges were split into three separate standards to line up with the IEC format. ANSI C8

22、1.61, ANS for Electric Lamp Bases paralleled IEC 60061-1; ANSI C81.62, ANS for Lampholders for Electric Lamps paralleled IEC 60061-2 and ANSI C81.63, Gauges for Electric Lamp Bases and Lampholders paralleled IEC 60061-3. Also a fourth standard, ANSI C81.64 Guidelines for Electrical Lamp Bases, Lamph

23、olders and Gauges was published to parallel IEC 60061-4 in 1993. In 1996, the first IEC data sheets were adopted “as is“ as Nationally Acknowledged International Standards and published as Supplement g to the existing C81.61, 62 and 63 standards. Now many more (if not most) ANSI gauge standard sheet

24、s are IEC sheets adopted as ANSI standards. In 2004, a revision and consolidation of ANSI C81.63 was issued to include, first, a reference to all IEC gauge standard sheets adopted as ANSI standards. Second, standard sheets for a small number of gauges used mainly in North America or not harmonized w

25、ith IEC were found in Part II. Part III contained any United States deviations to the IEC standard sheets, which had been adopted as Nationally Acknowledged International Standards as published in IEC 60061-3. Part IV contained an informative annex on first versus third angle projection and related

26、standards. ANSI C81.63-2007 (R2014) 2007 National Electrical Manufacturers Association iii Table of Contents Foreword ii Part I General Information and Requirements. 1 1 Scope 1 2 Normative references. 1 3 General information 1 Table 1 ANSI and IEC Lamp Base (Cap) Gauge Standard Sheets. 3 Table 2 AN

27、SI and IEC Lampholder Gauge Standard Sheets 8 Part II ANSI Standard Sheets for Gauges for Bases (Caps) and Lampholders for Electric Lamps 16 Part III United States Deviations to IEC Harmonized Gauge Standard Sheets 124 Annexes Annex A Contrast of Projection Methods on Engineering Drawings 125 Annex

28、B Related Standards 126 ANSI C81.63-2007 (R2014) iv 2007 National Electrical Manufacturers Association ANSI C81.63-2007 (R2014) 2007 National Electrical Manufacturers Association 1 PART I - General Information and Requirements 1 Scope This standard sets forth the specifications for gauges for bases

29、(caps) and lampholders for electric lamps. 1.1 Important Patent Disclaimer It is possible that some of the elements of this document may be the subject of patent rights. When this document was approved for publication, ANSLG did not know of any patent applications, patents pending, or existing paten

30、ts. ANSLG shall not be held responsible for identifying any or all such patent rights. 2 Normative references The following publications contain provisions which, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the editions indica

31、ted were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the publications indicated below. ANSI_ANSLG C81.61-2007, Bases (Caps) for Electric Lamps AN

32、SI_ANSLG C81.62-2007, Lampholders for Electric Lamps IEC 60061, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Caps IEC 60061-1 Ed. 3 including Amendment 39-2007 Part 2: Lampholders IEC 60061-2 Ed. 3 including Amendment 36-2007 Part 3: Gauges IEC

33、60061-3 Ed. 3 including Amendment 38-2007 3 General information Two types of gauge standard sheets are identified in this standard. For some gauges either no international standard exists or the international standard is not acceptable at this time. For such gauges an ANSI standard sheet is included

34、. These standard sheets are identified in Table 1- ANSI and IEC Lamp Base (Cap) Gauge Standard Sheets and Table 2- ANSI and IEC Lampholder Standard Sheets, under the column heading “ANSI_ANSLG C81.63“. These Standard Sheets are found in Part II. Certain standard sheets from IEC standard 60061-1 Lamp

35、 caps and holders together with gauges for the control of the interchangeability and safety, Part 3: Gauges, and its supplements, have been adopted as Nationally Acknowledged International Standards. These constitute part of the American National Standard for Gauges for lamp bases (caps) and lamphol

36、ders for electric lamps. The standard sheets for these gauges are not included, but are identified in Tables I and 2 under the column heading “IEC 60061-3“. If there are any United States deviations from these IEC standard sheets, the sheet number is marked with a footnote and the deviations are fou

37、nd in Part III. ANSI C81.63-2007 (R2014) 2 2007 National Electrical Manufacturers Association These IEC standards are available from: American National Standards Institute Attn: “eStandard Store” 25 West 42nd Street, 4th Floor New York, NY 10036 Or by calling 212 642-4900 during normal business hour

38、s. They may also be purchased electronically at the following URL www.ansi.org Or http:/webstore.ansi.org/ansidocstore/default.asp The drawings on the internationally standardized (IEC) sheets are in first angle projection rather than the third angle commonly used in the North American (ANSI) approv

39、ed standard sheets. Annex A shows the difference between the two systems. In addition, the common American term “Base“ is internationally known as “Cap“. Internationally the decimal point (.) is not used in dimensions, rather a comma (,) separates a decimal number e.g. 4,5 rather than 4.5. However i

40、n the designation of a fit the decimal point is used e.g. GY6.35. This Standard is used in conjunction with ANSI_ANSLG C81.61 “Bases (Caps) for Electric Lamps“ and ANSI_ANSLG C81.62, Electric Lampholders. This Standard is also used in conjunction with IEC 60061-1, Lamp caps and holders together with

41、 gauges for the control of interchangeability and safety, Part1: Lamp caps, and IEC 60061-2, Lamp caps and holders together with gauges for the control of interchangeability and safety, Part 2: Lampholders. ANSI C81.63-2007 (R2014) 2007 National Electrical Manufacturers Association 3 Table 1 - ANSI

42、and IEC Lamp Base (Cap) Gauge Standard Sheets System Description Standard Sheets IEC 60061-3 ANSI_ANSLG C81.63 Bayonet base gauges BA9 “Go“ Gauge for BA9 Miniature Bayonet Based Lamps 3-10-1 BA9 “Not-go“ Gauge for BA9 Miniature Bayonet Based lamps 3-11-1 BAW9s, BAZ9s “Go” gauges for caps on finished

43、 lamps 7006-9-2 BA15 “Go“ Gauge for BA15 Candelabra Bayonet Based Lamps 3-20-2 BA15 “Not-Go“ Gauge for BA15 Candelabra Bayonet Based Lamps 3-21-1 BY22d Gauges for testing the insertion of caps in lampholders 7006-4A-2 BY22d “Not-go“ gauges for caps on finished lamps 7006-10-8 BY22d “Go“ gauge for ca

44、p on finished lamp 7006-17A-1 Edison screw base gauges E5 “Go“ gauge for caps on finished lamps 7006-25D-1 E5 “Not go“ gauge for caps on finished lamps 7006-25E-1 E10 “Go“ gauge for caps 7006-27A-2 E10 “Not go“ gauge for caps 7006-28E-1 E11 “Go“ gauge for caps on finished lamps 7006-6-1 E12 “Go“ gau

45、ge for caps on finished lamps 7006-27H-1 E12 Additional “Go“ gauge for caps on finished lamps 7006-27J-1 E12 “Not go“ gauge for caps on finished lamps 7006-28C-1 E12 Gauge for finished lamps fitted with caps for testing contact making 7006-32-1 E17 Gauge for testing contact-making of lamps fitted wi

46、th caps 7006-26D-1 E17 “Go“ gauge for caps on finished lamps 7006-27K-1 E17 “Not go“ gauge for caps on finished lamps 7006-28F-1 E26, E26d, 26/50x39 “Go“ gauge for caps 7006-27D-2 E26, E26d, E26/50x39, E26/53x39 “Not go“ gauge for caps 7006-29L-4 E26, E26d, E26/50x39 Gauge for testing contact-making

47、 of lamps fitted with caps 7006-29-3 E26d Gauge for caps on finished lamps for testing protection against accidental contact. 7006-29A-2 E26d Gauge with reference diameter of 23mm (.906“) for caps 7006-29B-2 E26d Gauge with reference diameter of 13.2mm (.520“) for caps 7006-29C-2 E26d Gauge with ref

48、erence diameter of 10.4mm (.410“) for caps 7006-29D-1 E26/53x39 Threaded “Go“ Gauges for Unmounted E26/53x39 Skirted Bases and E26/53x39 Medium Screw Based Lamps 3-160-2 E26/53x39 Gauge for Testing Contact Making of E26/50x39 Skirted Medium Screw Based Lamps 3-166-2 E39, E39d, EX39 Gauge for finishe

49、d lamps fitted with E39 caps for testing contact making 7006-24A-1 E39, E39d, EX39 “Go“ gauge for caps on finished lamps 7006-24B-1 E39, EP39, E39d, EX39 “Not go“ gauge for caps on finished lamps 7006-24C-1 EP39 Threaded “Go“ Gauge for Position Oriented Mogul Screw Based Lamps 3-202-2 EP39 Gauge for Testing Contact Making of Position Oriented Mogul Screw Based Lamps 3-203-2 Single pin base gauges Fc2 Gauge for checki